Flashforge® Official Website
浙江闪铸集团有限公司 - 工业3d打印品牌-闪铸3d打印厂家【官网】
User Guide for FLASHFORGE models including: SZ20-ZN, EN-A02, SZ20-ZN Creator 3 FDM 3D Printer, SZ20-ZN, Creator 3 FDM 3D Printer, FDM 3D Printer, 3D Printer, Printer
Gembird Flashforge Creator3 (FF-3DP-2NC3-01) ▻ 3D принтер, 14 L ▻ купить в GEEK.MD
File Info : application/pdf, 36 Pages, 7.85MB
DocumentDocumentSZ20-ZN/EN-A02
Creator 3 / 3
Quick Start Guide
P17
1. Hot! Avoid touching the heating nozzle and heating build plate in operation.
2. Moving parts in printer may cause injury. Do not wear gloves or other sources of entanglement in operation.
Download
Please refer to FlashForge official website www.flashforge.com to download the newest User's Guide, Software and Instruction Videos. (Support-Support Center-Select a Product)
1. ! 2.
www.sz3dp.com [ ]
This guide is only applicable to FLASHFORGE Creator 3 3D printer 3 3D
1. Cut off packaging ties, and tear off stretch wrap.
2. Lift outer packing box.
3. Remove top foam.
4. Remove foam around the printer.
5. Unrip tapes on four corners of the printer, take bubble pack down.
6. Remove tapes on the top, open head cover.
01
7. Take top parts and foam out.
8. Remove the blue fastening tape.
9. Open the front door and take out the front foam which should contain two filament spools and two waste boxes.
10. Remove clips on timing belt of X-axis and Y-axis.
02
Build
Preheat
Tools
Filament
Level
HOME Home
Manual
Setting
Status
About
<
11. Plug power cable into the input on the back and turn on the power switch. Tap[Tools], [Manual].
Y +
X -
X +
Z -
X -
X +
Z +
Y -
X 0.00 X 0.00 Y 0.00 Z 0.00
<
12. Tap [Z-] to partially elevate the build plate. 13. Remove bottom foam pieces.
14. Now you've unpacked your Creator 3.
03
Getting to Know Your Creator 3
1. Touch Screen 5. Left Extruder 9. Leveling Nut 13. Turbofan Baffle
2. USB Stick Input
3. Touch Screen Buttom 4. Right Extruder
6. Nozzle Brush
7. Waste Box
8. Build Plate
10. Filament Cartridge Cover 11. Cartridge Cover Handle 12. Nozzle
14. Network Input
15. Power Switch
16. Power Input
04
SZ20-ZN/EN-A01
Creator 3 / 3
Quick Start Guide
1. Hot! Avoid touching the heating nozzle and heating build plate in operation.
2. Moving parts in printer may cause injury. Do not wear gloves or other sources of entanglement in operation.
Download
Please refer to FlashForge official website www.flashforge.com to download the newest User's Guide, Software and Instruction Videos. (Support-Support Center-Select a Product)
1. ! 2.
www.sz3dp.com [ ]
This guide is only applicable to FLASHFORGE Creator 3 3D printer 3 3D
Waste Box
Nozzle Brush
05
Build
Preheat
Tools
Filament
Level
HOME Home
Manual
Setting
Status
About
<
Language WIFI WLan hotspot Door Opened Pause
Door Opened Detector
English
English Deutsch
How to use the leveling nuts
Rotate the nut clockwise
Rotate the nut anticlockwise
06
Build
Preheat
Tools
1. Tap[Tools], tap[Level]to level the build plate.
Filament
Level
HOME Home
Manual
Setting
Status
About
<
Level Select the extruder
Left Extruder Right Extruder
OK
<
2. Wait for the extruder and the build plate moving, after moving completed, choose to use which extruder to level the build plate: left or right.
Please wait...Initializing
Verifying the distance between nozzle and plate...
<
Wait
<
3. After leveling extruder confirmed,extruder will move to the first point to verify the distance between nozzle and build plate. If verify completed, extruder will move to the second point to verify the distance.
Wait Turn the nut counterclockwise 90°
Wait Turn the nut clockwise 45°
Verify
Next
Verify
Next
4. If the distance is not appropriate, please follow the prompts to adjust again till you see [OK] button. Repeat steps 4 to level the second and third points. Then tap [Finish] to exit.
07
Install Waste box and Nozzle brush
Hook Hook 1. Take out waste box, hang it on the hook beside build plate. (One waste box on each side)
2. Take out nozzle brush, install it on mounting base. (One nozzle brush on each side)
08
Install Filament
1. Open the filament cover.
Filament intake
2. Insert the filament into filament intake.
3. Notice: For filament convenient rotation, please install filament follow the direction shown in the picture. When installing filament on the left side, please unload filament anticlockwise; when installing filament on the right side, please unload filament clockwise.
09
Press here
4. Insert filament into filament intake continuously until filament goes through filament guidetube.
5. Press the spring presser, put filament vertically into the left filament intake to the bottom.
6. Insert filament guidetube into filament intake to fix.
7. Put the spool of filament on the spool holder, close the filament cover.
10
Load Filament
Build
Preheat
Tools
Filament
Level
HOME Home
Manual
Setting
Status
About
<
1. Tap[Tools], [Filament] to enter the filament interface.
Load
Unload
Left Extruder is Heating...
Right Extruder is Heating...
Left Extruder Right Extruder
Left Extruder Right Extruder
Begin
<
31%
31%
69 / 220 Cancel
69 / 220
<
2. Flip the switch after corresponding extruder to 3. Tap[Begin], the extruder will start heating. load corresponding extruder.
Left Extruder Heated
Right Extruder Heated
Loading started, push filament vertically into extruder and press [Done] when you see filament come out of the extruder
Done
<
4. Once heated, filament will be drawn through the extruder. Continue extruding until the extruder provides a steady flow of filament. Tap [Done], go back. Tap leftwards arrow to go back to the home screen.
Attetion: If extruder can not unload in a long time, please check if you have inserted filament into the bottom of extruder.
11
Calibration
Please operate under the guidance of customer service for the first calibration.
Build
Preheat
Tools
Filament
Level
HOME Home
Manual
Setting
Status
About
<
Door Opened Remind Startup Sound Left Filament Check Right Filament Check Calibration
Z Calibration X Calibration Y Calibration
Tap [Tools], tap [Setting], tap [calibration] in setting page.
Z Calibration
Please level before Z-axis calibration. Please refer to the 06 page for leveling
Please wait... Auto calibration.
Wait
<
1. Tap [Z-axis calibration] and wait for Z-axis calibration of extruder and build plate. Do not interrupt during the calibration process.
12
X Calibration Check if the lines printed by 2 extruders aligned on X-axis to judge if the extruders on the same X-axis.
X Calibration Next
Recalibration
Skip
Reset
OK
Right Extruder is printing the 1st baseline then left extruder will print
the 1st alignment line.
<
1. Tap [X-axis calibration] and wait for extruders heating up. After heating up till target temperature, 2 lines will be printed in sequence. Check if the 2 lines are aligned after printing. Meanwhile, the pop-up window will appear.
X Calibration Next
Recalibration
Deviation000
Skip
Reset
OK
Adjust deviation, Press [Recalibration]
<
2. If the 2 lines are totally aligned, Tap [Yes], X-axis calibration is done. If the 2 lines are not totally aligned, Tap [No]. Adjust position of extruders according to actual situation. After that, clean the filament on build plate and Tap [Recalibration]. Repeat step 2 till the 2 lines are totally aligned.
13
Y Calibration Check if the lines printed by 2 extruders aligned on Y-axis to judge if the extruders on the same Y-axis.
Y Calibration Next
Recalibration
Skip
Reset
OK
Right Extruder is printing the 1st baseline and then left extruder will print
the 1st alignment line.
<
1. Tap [Y-axis calibration] and wait for extruders heating up. After heating up till target temperature, 2 lines will be printed in sequence. Check if the 2 lines are aligned after printing. Meanwhile, the pop-up window will appear.
Y Calibration Next
Deviation000
Recalibration
Skip
Reset
OK
Adjust deviation, Press [Recalibration]
<
2. If the 2 lines are totally aligned, Tap [Yes], Y-axis calibration is done. If the 2 lines are not totally aligned, Tap [No]. Adjust position of extruders according to actual situation. After that, clean the filament on build plate and Tap [Recalibration]. Repeat step 2 till the 2 lines are totally aligned.
14
Before the first printing, please complete the leveling, loading and calibration correctly under the guidance of the quick start guide.
Build
Preheat
Tools
1. Tap [Build].
PG.gx
2.7Mb 6834Mb
None
<
2. Tap [Local memory] to choose print files.
PG Total: 1 hr 48 min
Build
Copy
Delete
3. Choose the preset print file [PG.gx].
4. Tap [Build].
Left Extruder Mode
PG 0
30 30 30
1 hr 48 min Time left
5. The printer starts to heat up and will start printing after heating completed.
15
Unload Filament
Please follow steps below if you need to unload filament in daily use.
Build
Preheat
Tools
Filament
Level
HOME Home
Manual
Setting
Status
About
<
1. Tap[Tools], [Filament] to enter the filament interface.
Load
Left Extruder Right Extruder
Unload
Left Extruder Right Extruder
Begin
<
2. Tap the unload switch after corresponding extruder to unload corresponding extruder.
Withdraw Filament Guidetube
Left Extruder is Heating...
Right Extruder is Heating...
31%
31%
69 / 220
Cancel
69 / 220
<
3. Tap[Begin], the extruder will start heating. The printer will start unloading filament after heating completed.
Push filament down through for 3 seconds
Press here
4. Pull filament guide tube out of filament intake, leave filament 10cm to pull filament easily.
16
5. Press spring presser and push filament down through for 3 seconds, then pull out vertically quickly.
1.
2.
3.
4.
5.
6.
17
7.
8.
9. 3D
10. XY
18
Build
Preheat
Tools
Filament
Level
HOME Home
Manual
Setting
Status
About
<
11. [Tools][Manual]
Y +
X -
X +
Z -
X -
X +
Z +
Y -
X 0.00 X 0.00 Y 0.00 Z 0.00
<
12. [Z-] 13.
14.
19
1.
2. U
6.
7.
11. 12.
16.
3. 8. 13.
4.
5.
9. 10.
14. 15.
20
3D
3D
SZ20-ZN/EN-A01
Creator 3 / 3
Quick Start Guide
1. Hot! Avoid touching the heating nozzle and heating build plate in operation.
2. Moving parts in printer may cause injury. Do not wear gloves or other sources of entanglement in operation.
Download
Please refer to FlashForge official website www.flashforge.com to download the newest User's Guide, Software and Instruction Videos. (Support-Support Center-Select a Product)
1. ! 2.
www.sz3dp.com [ ]
This guide is only applicable to FLASHFORGE Creator 3 3D printer 3 3D
U
21
Build
Preheat
Tools
Filament
Level
HOME Home
Manual
Setting
Status
About
<
Language WIFI WLan hotspot Door Opened Pause
Door Opened Detector
English
English Deutsch
1. [Tools][Setting][Language][] 2.
22
1. [][]
HOME
<
...
<
2.
...
...
<
<
3.
90
45
4. [OK]
23
1.
2.
24
1.
2.
3.
25
4.
5.
6.
7.
26
1. [][]
HOME
<
<
...
...
31%
31%
69 / 220
69 / 220
<
2. [] 3. []
[]
<
4. []
27
HOME
<
Z X Y
1. [][][]
Z Z18
... Z
<
1. [Z]Z
28
X XX
X
1 1
<
1. [X]
X
000
[]
<
2. []X[] []
29
Y YY
Y
1 1
<
1. [Y]
Y
000
[]
<
2. [] []
30
1.
2.
3.
4. ABS
PLA
5.
6. 3D
1. []
PG.gx
2.7Mb 6834Mb
None
<
2. []
3. [PG.gx]
4. []
PG : 1 hr 48 min
PG 0
30 30 30
1 hr 48 min
5.
31
1. [][]
HOME
<
...
...
<
31%
69 / 220
31%
69 / 220
<
2. [] 3. []
3
4.
5. 3
32