A4000033 Assembly Instructions
Signature Design by Ashley
Important Note: Your unit may look different in appearance from the one shown in the illustrations on this instruction sheet.
(This note is also provided in Spanish and French.)
Important Safety Information
⚠️ Read Carefully Before Beginning Assembly
- Always assemble in a well-lit area.
- Keep small parts and hardware away from children.
- Do not use substitute parts.
- Keep these instructions for future reference.
- For products with electrical cords (lamps, etc.), ensure power is disconnected before installation and do not twist the cord during installation.
- When installing shelves or TV cabinets, do not stand on lower shelves; use a ladder for installation.
- Do not stand on tables such as coffee tables, end tables, or dining tables, as they are not designed to support human weight.
- If assembly requires two or more people, do not attempt to assemble alone.
- Use appropriate tools for assembly.
- Follow assembly steps sequentially; do not skip any steps.
- Carefully check packaging materials for small parts that may have scattered during shipping. Contact your local retailer for missing parts; do not substitute.
- Periodically check all connections (screws, bolts, etc.) to ensure they are tight.
- When the product uses glass or mirrors, handle with care during installation to prevent injury from breakage. Do not install large glass or mirrors alone.
(Multilingual safety notes are present in the original document.)
Liability Disclaimer: Ashley Furniture Industries, LLC is not responsible for losses or injuries resulting from failure to strictly follow assembly instructions, incorrect assembly, or incorrect product usage.
Parts List
The following parts are included:
- Part A: [Main Panel/Surface] (x1)
- Part B: [Side Panel] (x1)
- Part C: [Base/Side Panel] (x1)
- Part D: [Shelf] (x1)
- Part E: [Back Panel] (x1)
- Part F: [Door Hinge] (x2)
- Part G: [Door Handle] (x2)
- Part H: [Cam Lock] (x4)
- Part J: 1/4" x 38mm Screw (x8)
- Part K: 1/4" x 32mm Screw (x1)
- Part L: [Shelf Support Pin] (x4)
- Part M: [Foot Leveler] (x1)
- Part N: [Small Screw] (x2)
Hardware Details:
- Screws: 1/4" x 38mm (J, x8), 1/4" x 32mm (K, x1)
- Other Hardware: Cam Locks (H, x4), Hinges (F, x2), Handles (G, x2), Shelf Pins (L, x4), Foot Leveler (M, x1), Small Screws (N, x2)
Note: The diagram for Part K indicates "Not Included", but it is used in assembly steps.
Replacement Parts: For replacement parts, contact RTAParts@ashleyfurniture.com, visit www.ashleyfurniture.parts, or call 1-844-966-0809.
Assembly Steps
Important Assembly Note: The unit should be assembled by two or more people. Do not tighten any bolts until all bolts have been started.
(This note is also provided in Spanish and French.)
-
Step 1: Connect Part A to Part C using hardware J (x6).
Visual: Shows Part A being attached to Part C at a right angle, with screws (J) being inserted through pre-drilled holes on one panel into the edge of the other.
-
Step 2: Connect Part C to Part B using hardware K (x6).
Visual: Shows another panel (C) being attached to a side panel (B) at a right angle, using screws (K). A close-up shows screw K being driven into a pilot hole.
-
Step 3: Insert Part E (back panel) into the unit.
Visual: Shows a thin panel (E) being slid into grooves along the back edges of the assembled side and base panels.
-
Step 4: Attach Part B (top panel) to the assembly. Use hardware K (x4) and cam locks (H, x4).
Visual: Shows the top panel (B) being placed on top of the assembled sides and back. Cam locks (H) are shown being inserted into larger holes on the top panel and then turned to secure to studs on the side panels. Screws (K) are also shown being used.
-
Step 5: Install door hinges (F) onto the doors and the main unit. Attach the doors using the hinges.
Visual: Shows hinges (F) being screwed onto the edges of the doors and then attached to the front edges of the side panels.
-
Step 6: Insert shelf support pins (L) into the desired holes inside the cabinet. Place the shelf (D) onto the pins.
Visual: Shows small pins (L) being inserted into holes on the inside of the side panels at various heights. A shelf (D) is then shown being placed on top of these pins.
-
Step 9: Attach the foot leveler (M) to the bottom of the unit.
Visual: Shows a foot leveler (M) being screwed into the bottom of one of the base panels. A separate diagram shows how to adjust the leveler to make the unit stable on an uneven floor.
Final Installation Note: If the unit is placed on an unlevel surface, place a leveler underneath one foot until the unit is level. Break off any protruding segments.
(This note is also provided in Spanish and French.)
⚠️ Tipping Restraint Warning: The use of the included tipping restraint may reduce, but not eliminate, the risk of furniture tip over. Follow the instructions on the plastic bag for proper installation.
(This warning is also provided in Spanish and French.)
