Hampton Bay Solar LED String Light

Introduction

Thank you for purchasing the Hampton Bay Solar LED String Light. This guide provides essential information for installation, operation, maintenance, and troubleshooting to ensure optimal performance and longevity of your product.

For questions, problems, or missing parts, please contact Hampton Bay Customer Service:

Phone: 1-855-HD-HAMPTON

Website: HAMPTONBAY.COM

Customer Service Hours: Monday-Friday 8 a.m. - 7 p.m. EST, Saturday 9 a.m. - 6 p.m. EST.

Safety Information

⚠️ WARNING: Your solar light may not function in temperatures below -4°F (-20°C) or above 140°F (60°C).

⚠️ CAUTION: Use a rechargeable battery only. Recycle or dispose of batteries properly.

⚠️ CAUTION: Do not open, short circuit, or mutilate batteries as injury may occur.

Warranty

One Year Limited Warranty

What is Covered

The manufacturer warrants this product to be free of defects in material and workmanship for a period of one (1) year from the date of purchase. This warranty applies only to the original consumer purchaser and to products used in normal service. The manufacturer's sole obligation and your exclusive remedy is the repair or replacement of the product at the manufacturer's discretion, provided the product has not been damaged through misuse, abuse, accident, modification, neglect, or mishandling. Proof of purchase and manufacturer's date coding must accompany all warranty claims.

What is Not Covered

This warranty does not apply to products that are improperly installed, set up, or used in any way not in accordance with the instructions. It does not apply to product failure resulting from accident, misuse, abuse, negligence, alteration, or faulty installation. Batteries supplied with this product are not included in this warranty. The finish on any portion of the product, such as surfaces and weathering, is considered normal wear and tear and is not covered. The manufacturer does not warrant fitness for a particular purpose and expressly disclaims any such warranty. This warranty does not cover consequential or incidental loss or damage, including labor/expense costs involved in replacement or repair.

Contact the Customer Service Team at 1-855-HD-HAMPTON or visit HAMPTONBAY.COM.

Pre-Installation

Planning Installation

Ensure the mounting location for your solar light allows the solar panel to receive direct sunlight. Do not locate the product in shaded areas, as this will significantly reduce performance. Position the solar light such that during evening hours, ambient light from other sources does not affect the photosensor built into the solar panel. High ambient light levels can cause the lamp to turn off during evening hours.

Note: The solar light is equipped with a photosensor that turns the unit on at dusk and off at dawn. Ambient light can affect the operation of the photosensor.

Tools Required

Diagram Description: Visuals depict a Phillips screwdriver and an electric drill.

Hardware Included

Note: Hardware is not shown to actual size.

Package Contents

Diagram Description: Visuals show the following components:

• A: Solar assembly/LED string
• B: Pole connector
• C: Pole
• D: Ground stake
• E: Battery (Pre-assembled)

Installation

1. Installing the Solar Box in the Ground

Diagram Description: Illustrates the assembly process for ground installation, showing the ground stake (D), pole (C), pole connector (B), and solar assembly (A).

• Insert the ground stake (D) firmly into the ground at the installation location. If the ground is too hard, soak the ground with water to soften it or drive a metal rod or screwdriver into the ground to create a hole for the ground stake assembly.
• Connect the pole (C) to the ground stake (D).
• Slide the pole connector (B) into the mounting slot on the back of the solar assembly (A).
• Connect the installed pole connector (B) on the solar assembly (A) to the pole (C).
• Your solar light is equipped with a 3-way selector (FLASHING, OFF, ON) on the back of the solar assembly (A). Prior to use, set the selector to the FLASHING or ON position and allow it to charge for a full sunny day.

Note: Do not use a hammer. If the ground is hard, use water to soften.

2. Installing the Solar Box to the Wall

Diagram Description: Illustrates mounting the solar assembly (A) to a wall surface using screws (AA) and wall anchors (BB).

• If mounting to a wood surface, drill two 3/32 in. holes into the mounting surface. Insert the mounting screws (AA) into the holes, leaving about 1/4 in. of the screws (AA) sticking out of the wood surface.
• If mounting to a wall board or brick walls, drill two 7/32 in. holes into the wall surface and insert the wall anchors (BB). Insert the mounting screws (AA) into the anchors (BB), leaving about 1/4 in. of the screws (AA) sticking out of the wall surface.
• Align and place the two mounting slots on the side of the solar assembly (A) over the mounting screws (AA), slide down to secure it in position.
• Your solar light is equipped with a 3-way selector (FLASHING, OFF, ON) on the back of the solar assembly (A). Prior to use, set the selector to the FLASHING or ON position and allow it to charge for a full sunny day.

Maintenance

Replacing the Battery

Diagram Description: Shows the rear of the solar assembly (A) with the battery compartment lid (F) secured by screws (G), and the battery (E) inside.

• IMPORTANT: Dispose of the battery in accordance with local, state, and federal regulations.
• IMPORTANT: When storing any solar product for an extended period of time, remove the batteries. Storing any solar product without regular recharge or removal of batteries could cause permanent damage to the rechargeable batteries.
• Note: Use one AA-size, 600mAh, 1.2V nickel-metal hydride rechargeable battery. For best performance, replace with a nickel-metal hydride rechargeable battery annually.
• Unscrew the battery compartment lid (F) from the back of the solar assembly (A) and remove it.
• Remove the old batteries (E). Replace with one new AA size, 1.2V Nickel Metal Hydride rechargeable battery. The recommended replacement battery capacity should be 600mAh or above.
• Replace the battery compartment lid (F) with the two screws (G).

Care and Cleaning

• The solar panel should be cleaned periodically with a damp cloth to help maintain optimum performance.
• Do not use any cleaners with chemicals, solvents, or harsh abrasives.

Troubleshooting

Diagram Description: A table outlines common issues, their potential causes, and recommended solutions.