Audioxtra – Australian importer and distributor of Axis, Blaupunkt, Dynamat, HEMA Maps, Midland and Uniden
Installation Guide for axis models including: APS401T, 12 24V Parking Sensor System
3 1/8 1/4 1/4 1/4 1/8 SENSOR INSTALLATION DIAGRAM 0. 5 ~ 0. 8 m Fix the plsition of sensors. No obstacle should be detected at 90° from the top view otherwise the system will false alarm.
Adjust the direction and orientation of sensors. Neaten the wiring after installation. 2. Connect the power wire to the reversing light circuit.
File Info : application/pdf, 12 Pages, 2.02MB
DocumentDocumentJAPAN QUALITY APS401T 12/24V Parking Sensor System 1 2 0.5~0.8m SENSOR INSTALLATION DIAGRAM Fix the plsition of sensors. No obstacle should be detected at 90° from the top view otherwise the system will false alarm. Installation distance dragram 1/8 1/4 1/4 1/4 1/8 Best position for 4 sensors Installation diagram for sensors with direction markings Installation diagram Installation when bumper is sloping to the ground. 3 Smooth slope Smooth round objects Objects sbsorbing wave,e.g.cotton Objects hard to be detected ADVISED POSITION TO INSTALL THE SENSOR A. Four drill holes A.B.C.D should be in line. B. 0.5~0.8m vertical to the ground. 0.55m is recommended. C. Vertical, tidy surface without metal components is preferred. 4 SELECT DRILLING POSITION FOR SENSOR A&D A. Choose suitable drilling positions for A and D sensor and mark. For best detection angle, position A & D sensor 1/8 from the edge. SELECT DRILLING POSITION FOR SENSOR B&C A. Measure the distance between sensor A and D. Divide distance by 3 and mark sensor B & C. 5 DRILLING A. Use a small drill bit to locate position B. Drill with the bumper cutter supplied. SENSOR INSTALLATION A. Insert the sensors into the holes and secure. B. Arrange wiring neatly and securely. BUZZER INSTALLATION Buzzer Paste the buzzer on the center console or the rear of the seat. 6 CONTROL BOX INSTALLATION Install the control box on the bottom of the vehicle and fix it by screw. NOTE: Control box is waterproof. 1.5m 7 PARKING SENSOR SYSTEM This system consists of ultrasonic sensors,a control unit and buzzer This system detects the distance between the vehicle and obstructions by ultrasonic sensors installed at the rear of the vehicle. The distance and direction of the obstruction will be showed by audible buzzer with step-up "BiBi" sounds. MAIN FEATURES Audible buzzer Volume Adjustable Four stages "BiBi" alarm sound Hidden installation TECHNICAL SPECIFICATIONS Rated Voltage: 12V/24V Operating Range: DC 10~32V Operating Current: 10-120mA Detecting Distance: 0.3~1.5m Ultrasonic Frequency: 40KHz Working Temperature: -20~+70°C Detecting distance 1.6m 1.1~1.5m 0.6~1.0m 0.4~0.5m 0.3m Alarm sound Silence Bi............Bi............ Bi.........Bi......... Bi......Bi...... Bi... 8 INSTALLATION STEPS 1. Carefully choose position for sensors 2. Select drilling position for sensor A&D 3. Select drilling position for sensor B&C 4. Locate the position and drill 5. Install the sensors and hide the wires 6. Install the Buzzer 7. Install the control box (NOTE: The control box is waterproof) TEST 1. Adjust the direction and orientation of sensors. Neaten the wiring after installation. 2. Connect the power wire to the reversing light circuit. 3. Connect the wires between contor box and Buzzer. 4. After starting the car, the Buzzer will sound one time on power up. Insert one sensor into the control box port. within 1.0m of hte sensor, it should detect normally. Disconnect this sensor from the control box and use the same method to check other sensors. Then insert all sensors into matching ports. NOTE 1. The car must be off during the installation 2. Performance may be affected in heavy rain, gravel roads, bumpy roads, hot or moist weather, or it the sensor is covered by ice or mud. 3. Other ultrasonic or electric waves (eg voltage reducers) may affect the performance of the system. 4. The sensors should be installed securely but not over-tight. 5. Rubber sensors are designed to avoid "Metal resonance" in metal bumpers. 6. Avoid installing the digital control box in areas of interference or moisture. 7. Test the system to make sure it works correctly. 8. This system is a reversing aid and the manufacturer accepts no responsibility for and accident after the kit is installed. 9 NOTES 10 SPECIFICATIONS GENERAL - Detection Range: - Rated Voltage: - Operating Range: - Operating Current: BUZZER - Proximity Alert: - Audiable Buzzer: - Buzzer Cable Length: CONTROL BOX - Water Resistance - Power Leads: - Dimensions: SENSORS - Sensor Type: - Sensor Size: - Sensor Dimensions: - Sensor Cable Length: - Sensor Installation: - Detecting Distance: - Working Temperature: - Water Resistance - Under Mount Dimensions: INCLUDES Control Box 4 x Sensors Buzzer 4 x Brackets with Pads 4 x 3 Sensor Cable Drill Bit 0.3 ~ 1.5m 12/24V DC 9-32V DC 350mA @ 12V Audible Tone Yes 15.8m IP67 1.4m 106W x 27H x 80Dmm Angled Rubber 20mm 26W x 26H x 23.8Dmm 2.1m Under Mount or In-Bumper Mount 0.3 - 1.5m -30° to +85°C IP68 61W x 31H x 22.4Dmm 11 WARRANTY Congratulations on your purchase of a quality Mobile Safety System! You're joining thousands of satisfied customers who enjoy & experience the benefits of the products we distribute. In the unlikely event that some technical difficulty arises with your purchase, be assured that we are most anxious to see that the problem is quickly rectified to your satisfaction. Please familiarise yourself with the following simple conditions of our warranty. This warranty covers faults through component failure or failure of the product to operate in accordance with published specifications. Product failure as a result of unreasonable environmental conditions, accident, misuse, improper installation, unauthorised repair, vehicle electrical or wiring faults or neglect etc, will not be covered by this warranty. Removal and installation costs, if any, would be paid by the owner as well as any freight or postage costs of transporting the product to AudioXtra. AudioXtra shall not be liable or responsible for any loss of use of this product or any form of consequential loss. CONSUMER WARRANTY This product is warranted by AudioXtra Pty Ltd to be free from defects in materials and workmanship under NORMAL USE for a period of TWENTY FOUR MONTHS from the date of purchase. WITHIN 30 DAYS OF PURCHASE DATE: Please return the unit for replacement to our National Service Centre or the Retailer from where you made the purchase. All accessories must be included. Proof of purchase date must accompany the products. AFTER 30 DAYS OF PURCHASE DATE: Warranty repair and service is carried out by our National Service Centre. Repair and service will be carried out at no cost to the owner if proof of ownership and the date of purchase can be verified to the satisfaction of the authorised centre concerned with this repair. This proof should take the form of either: a) The warranty card accompanying this product, stamped and dated by the dealer. b) A Tax Invoice or Receipt showing full details of original vendor, purchaser, model number and serial number. COMMERCIAL WARRANTY A product used in or associated with a commercial application will carry a limited SIX MONTH warranty. An abnormal commercial application is one where usage, dust, vibration, heat/cold and other environmental conditions exist at an extreme level. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Please complete details below in the event of warranty service being required. Purchaser's Name: Purchaser's Address: Model Number: APS401T Serial Number: Dealer Name: Date of Purchase: / / Dealer Address: Invoice/Sales Docket no: General Hints: To expedite service and prompt return of the equipment, please: a) Clearly describe the fault in detail c) Include your return address b) Safely and securely pack the unit for transport d) Provide proof of purchase date as outlined above National Service Centre: 10 STODDART ROAD, PROSPECT, SYDNEY NSW 2148 Australia Telephone: (02) 8841 9000 Fax: (02) 9636 1204 email: services@audioxtra.com.au PTY LTD audioxtra.com.au 12