Thank You Letter
Thank you for choosing Midea! Before using your new Midea product, please read this manual thoroughly to ensure that you know how to operate the features and functions that your new appliance offers in a safe way.
Contents
- Thank You Letter
- Safety Instructions
- Specifications
- Product Overview
- Product Installation
- Operation Instructions
- Cleaning and Maintenance
- Troubleshooting
- Trademarks, Copyrights and Legal Statement
- Data Protection Notice
Safety Instructions
Intended Use
The following safety guidelines are intended to prevent unforeseen risks or damage from unsafe or incorrect operation of the appliance. Please check the packaging and appliance on arrival to make sure everything is intact to ensure safe operation. If you find any damage, please contact the retailer or dealer. Please note modifications or alterations to the appliance are not allowed for your safety concern. Unintended use may cause hazards and loss of warranty claims.
Explanation of Symbols
⚠DangerThis symbol indicates that there are dangers to the life and health of persons due to extremely flammable gas.
⚠Warning of electrical voltageThis symbol indicates that there is a danger to life and health of persons due to voltage.
!WarningThe signal word indicates a hazard with a medium level of risk which, if not avoided, may result in death or serious injury.
!CautionThe signal word indicates a hazard with a low degree of risk which, if not avoided, may result in minor or moderate injury.
💡AttentionThe signal word indicates important information (e.g. damage to property), but not danger.
⚒Observe instructionsThis symbol indicates that a service technician should only operate and maintain this appliance in accordance with the operating instructions.
Read these operating instructions carefully and attentively before using/commissioning the unit and keep them in the immediate vicinity of the installation site or unit for later use!
Important Instructions
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, injury to persons, and hyperthermia, including the following:
- Read all instructions before using this heater.
⚠ CAUTION- This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front of the heater and keep them away from the sides and rear.
- Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
⚠ WARNING- Always unplug heater when not in use.
- Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Discard heater, or return to authorized service facility for examination and/or repair.
- Do not use outdoors.
- This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate heater where it may fall into a bathtub or other water container.
- Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.
- To disconnect heater, turn controls to off, then remove plug from outlet.
- Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
- To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
- A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
- Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
- Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip).
- Hyperthermia can result in death. Symptoms of hyperthermia include high body temperature, headache, nausea, vomiting, tiredness, dizziness, fainting, and rapid pulse. If you begin to experience symptoms related to hyperthermia, turn off the heater and seek medical attention.
- To avoid excessive room temperatures which can cause hyperthermia: DO NOT leave product running unattended in a confined space around infants, or individuals with reduced physical, sensory, or mental capabilities.
SAVE THESE INSTRUCTIONS
Specifications
| Product Model | MSF15AH6LB |
|---|
| Voltage | 120V~ |
| Frequency | 60Hz |
| Fan Power | 40W |
| Heater Power | 1500W |
| Noise | ≤62dB |
Product Overview
Part Name
The appliance features a Control Panel and Display Panel at the top. Air Outlet is located at the upper front. A Heater (red)/Fan (blue) Mode indicator light is present. The main body rests on a Base. On the side, there is an Air Inlet Grille. Internally, it contains a Pre-filter and a HEPA Filter.
Part List
- Remote Controller ×1
- Manual ×1
- HEPA Filter ×2
NOTE: All the pictures in this manual are for explanation purpose only. Any discrepancy between the real object and the illustration in the drawing shall defer to the real product.
Product Installation
Installation Procedures
- Remove the air inlet grille.
- Take out the pre-filter. Press the raised part on both sides to pull it outwards, and take out the pre-filter.
- Remove the protective film of the filter.
- Install the HEPA filter.
- Install the pre-filter. Align the slot position at the bottom, and snap fit the upper U-Shaped joint to install.
- Install the air inlet grille. Align the upper two snap fit joints and press them tightly together to fasten, then press the two sides together at the bottom, slowly and gently snap fit the air inlet grille into place.
- Plug power supply.
It is recommended to clean the pre-filter every two weeks and replace the pre-filter every six months (The cleaning and replacement cycle can be adjusted according to the use environment).
Operation Instructions
Panel Control & Display
The control panel includes buttons for COOL/MODE, LIGHT, WARM, TIMER, AUTO, and OSC (Oscillation), along with a power ⑂ button and +/- buttons. The display panel shows temperature, fan speed, and mode indicators.
| ICON | Function description |
|---|
| ⑂ | • Touch ⑂ to enter Startup/Standby, the appliance starts up or stops. |
| −/+ | • Touch −/+ to set cool wind speed and desired timer. |
| ↻ | • Touch ↻ to set the desired oscillation angle of 30°, 55°, or 0° (Stop oscillation). |
| 💨 | • Touch 💨 to set the cool wind mode. Touch this button to switch the wind mode among Normal wind (12 speeds settings, 💨 lights up), Sleep wind (3 speed settings, 💤 lights up), and Natural wind (3 speed settings, 🍃 light up). |
| ⏱ | • Schedule to stop working automatically in the power-on state, and schedule to start working automatically in the standby state;
• Touch ⏱ and press +/- to set the timer in one hour intervals up to 12 hours (the display cycles among 0-1-2-...-12-Oh); Oh means the set timer is canceled. |
| 💡 | • Touch 💡 to turn on/off the ambient light. |
| 🌬 | • Touch 🌬 to enter Auto wind mode, and the wind power is automatically adjusted according to changes in ambient temperature. |
| ☀ | • Touch ☀ to activate heating mode, touch +/- to set target temperature. "--" indicates target temperature is not set. If the target temperature is set and the appliance does not reach the set temperature, the appliance will continue to work until the actual temperature exceeds the set temperature, and then, the machine will stop. The icon ☀ on the display flashes for 15 seconds and then stays on. |
| 🍃 | • In the natural wind mode, this indicator light turns on.
• You can switch the wind speed between 1 - 2 - 3 speeds by touching the speed button. |
| 💧 | • When this indicator light stays on, it serves as a reminder to replace the filter. |
| ⚡ | • The indicator light turns on indicating that the power plug is plugged in. |
Remote Control
- The remote control should be normally used within 16 ft (5m) of the front of the product and 30 degrees of the deviation angle.
- The battery contains many heavy metals, acids and bases, etc., which may threaten human's health. Waste batteries should be recycled separately.
The remote control features buttons for TIMER, Desired oscillation angle setting, Wind mode, Warm mode, Startup/Standby, and +/- for adjusting wind speed or timer. It uses AAA 1.5V batteries.
NOTE: Use manganese or alkaline batteries of type “AAA”. DO NOT use rechargeable batteries.
Batteries Warning As Below
- Do not dispose of batteries in fire, batteries may explode or leak.
- Do not mix old and new batteries.
- Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.
- Non-rechargeable batteries are not to be recharged.
- Batteries are to be inserted with the correct polarity.
- Exhausted batteries are to be removed from the product.
- The batteries must be removed from the remote controller before it is scrapped and that they are disposed of safely.
Additional Features and Maintenance
- Forced shutdown: Please note that as a safety measure, the fan will automatically shut down after 15 hours of continuous operation if no additional actions or operations are performed. This ensures the unit's optimal performance and prevents any potential overheating or damage.
- Intelligent memory: When the fan is turned off or powered off, it will run in the same state before turning off or power off when the power is powered on again (the timing function is not memorized).
- Screen-off function: The screen display will automatically shut-off after 30 seconds if no additional actions or operations are performed. To turn on the screen you can touch any button other than ON/OFF to restore the display.
NOTE: When the screen is off, touching the ON/OFF button will turn the appliance off.
Cleaning and Maintenance
It is recommended that the appliance be cleaned at least one time during the operating season in order to provide the optimum level of performance. ALWAYS TURN THE POWER SWITCH OFF AND UNPLUG THE APPLIANCE BEFORE CLEANING. Be sure to save the box for storage. If the appliance is broken or damaged, do not try to fix it by yourself. Refer it to an authorized service representative if service is needed.
- Before cleaning and assembling, appliance must be unplugged.
- To ensure adequate air circulation to the motor, keep vents at the rear of the motor free of dust. Do not disassemble the appliance to remove dust.
- Please clean external parts using a soft clean cloth moistened with a mild detergent. thoroughly remove soap film with dry cloth.
- Do not use any abrasive detergent or solvents to avoid scratching the surface. Do not use any of the following as a cleaner: gasoline, thinner.
- Do not allow water or any other liquid into the motor housing or interior parts.
Filter Replacement
- Filter model: FQ150CJ-2 (including 2 pieces).
- When the indicator light for filter replacement is on, it serves as a reminder to replace the filter. Failure to do so will result in the indicator light remaining illuminated when the appliance is powered on.
- Replace with a new filter.
- Press and hold the ↻ button for 3 seconds to turn off the indicator light for filter replacement.
Pre-Filter Cleaning
- Unplug the power cord.
- Take out the filter.
- Remove the dust with vacuum cleaner.
- Reinstall the pre-filter in reverse order and then plug-in the power supply.
Troubleshooting
The appliances may encounter some errors and malfunctions, the following tables contain possible causes and notes for resolving an error or malfunction.
| Problem | Cause | Solution |
|---|
| The unit does not work properly after assembled | • The power cable is not plugged in or has poor contact. | Make sure the plug is properly inserted into the socket. |
| • The power on/off button is not activated. | Press the power on/off button to turn on the appliance. |
| The remote does not work | • The battery is out of power. | Replace with new battery. |
| • The remote is being used more than 16 ft (5m) away from the appliance. | Use the remote closer to the appliance and make sure it is pointing directly at the display panel. |
- The machine stops when the temperature exceeds the threshold of the thermal cut-off, you should manually unplug the appliance, and then insert it into the receptacle again when the appliance is cooled.
- When you are not using the appliance, store it in a cool, dry place with ambient conditions and no dust, to avoid clogging the filters.
Trademarks, Copyrights and Legal Statement
The Midea logo, word marks, trade name, trade dress and all versions thereof are valuable assets of Midea Group and/or its affiliates (“Midea”), to which Midea owns trademarks, copyrights and other intellectual property rights, and all goodwill derived from using any part of an Midea trademark. Use of Midea trademark for commercial purposes without the prior written consent of Midea may constitute trademark infringement or unfair competition in violation of relevant laws.
This manual is created by Midea and Midea reserves all copyrights thereof. No entity or individual may use, duplicate, modify, distribute in whole or in part this manual, or bundle or sell with other products without the prior written consent of Midea.
All the described functions and instructions were up to date at the time of printing this manual. However, the actual product may vary due to improved functions and designs.
Data Protection Notice
For the provision of the services agreed with the customer, Midea agrees to comply without restriction with all stipulations of applicable data protection law, in line with agreed countries within which services to the customer will be delivered, as well as, where applicable, the EU General Data Protection Regulation (GDPR).
Generally, Midea's data processing is to fulfil its obligation under contract with customers and for product safety reasons, to safeguard customer rights in connection with warranty and product registration questions. In some cases, but only if appropriate data protection is ensured, personal data might be transferred to recipients located outside of the European Economic Area.
Further information is provided by request. Customers can contact Midea's Data Protection Officer via MideaDPO@midea.com. To exercise rights, such as the right to refrain personal data being processed for marketing purposes, customers can contact Midea via MideaDPO@midea.com. For further information, please follow the QR Code (not included in HTML).
Models: MSF15AH6LB, MSF15AH6LB 3 In 1 Fan Heater Air Purifier, 3 In 1 Fan Heater Air Purifier, Fan Heater Air Purifier, Air Purifier, Purifier
