Sun Joe Pressure Washer Auto Cleaning System Accessories & Guides
Model: SPX-ACS-MAX
For questions or comments, contact the Snow Joe® + Sun Joe® customer service department at: ? 1-866-SNOWJOE (1-866-766-9563)
⚠️ WARNING! To reduce the risk of injury, read and understand the operator's manual for your pressure washer before using this cleaning system. To reduce the risk of injury or property damage, spray the pressure stream in a safe direction to ensure proper connection of all accessories before starting any cleaning project. Ensure compatibility and proper fit before using this accessory. Wear eye protection. Do not point at people, pets, electrical devices, or the unit itself. Turn off the pressure washer, relieve water pressure in the trigger handle, and lock the safety lock on the trigger handle (if included) before installing, changing, or adjusting accessories. For cold water use only. For outdoor use only.
© 2021 by Snow Joe®, LLC. All rights reserved. Original instructions. Made in China.
Adapter Quick Guide
This guide details adapters for connecting Snow Joe® pressure washer accessories to other brands.
Adapter A: AR Blue Clean® Pressure Washer Adapter
Converts Snow Joe® pressure washer accessories to fit AR Blue Clean® pressure washers up to 2320 PSI.
Adapter B: Kärcher® Pressure Washer Adapter
Converts Snow Joe® pressure washer accessories to fit Kärcher® pressure washers up to 2320 PSI.
Adapter C: Nilfisk® Pressure Washer Adapter
Converts Snow Joe® pressure washer accessories to fit Nilfisk® pressure washers up to 2320 PSI.
Adapter D: Anlu® Pressure Washer Adapter
Converts Snow Joe® pressure washer accessories to fit Anlu® pressure washers up to 2320 PSI.
Adapter E: Ryobi® + Greenworks® Pressure Washer Adapter
Converts Snow Joe® pressure washer accessories to fit Ryobi® + Greenworks® pressure washers up to 2320 PSI.
M22 Adapter
Converts a 15 mm M22 Female connection to a 14 mm M22 Male fitting.
Metal Gun Adapter
Converts M22 to a bayonet fitting.
NOTE: No adapter is needed for Earthwise™ pressure washers up to 2320 PSI.
The enclosed products are not manufactured, distributed, or endorsed by Earthwise™, AR Blue Clean®, Kärcher®, Nilfisk®, Anlu®, Ryobi®, or Greenworks®, which own their respective trademarks. Sun Joe® and its affiliates are not related to, affiliated with, or endorsed by Earthwise™, AR Blue Clean®, Kärcher®, Nilfisk®, Anlu®, Ryobi®, or Greenworks®.
Utility Bristle Brush Assembly Quick Guide
NOTE: These instructions are for connecting with SUN JOE® Pressure Washers only. For connecting with other brands' pressure washers, use the corresponding transfer adapter. Refer to page 2 for details.
For SPX200/SPX1000 Series
Assembly Components: Trigger Gun, Middle Wand, Utility Brush.
Instructions:
- Disconnect your spray wand assembly so only the middle wand remains attached to your trigger gun.
- Take the utility brush and align it with the middle wand.
- Once aligned, push the utility brush into the middle wand and twist to lock into place (follow the arrow in the illustration).
For SPX2000, SPX2500, SPX2600, SPX4003, SPX4003-ULT
Assembly Components: Trigger Gun, Utility Brush.
Instructions:
- If not already done, detach your spray wand from your trigger gun.
- Take the utility brush and align it with the inside of the trigger gun.
- Once aligned, push the utility brush into the trigger gun and twist to lock into place (follow the arrow in the illustration).
For Most SPX2000 Series + SPX4003-ELT, SPX7001E
Assembly Components: Trigger Gun, Utility Brush.
Instructions:
- If not already done, detach your spray wand from your trigger gun.
- Take the utility brush and align it with the inside of the trigger gun.
- Once aligned, push the utility brush into the trigger gun and twist to lock into place (follow the arrow in the illustration).
For Most SPX3000 Series + Most SPX4000 Series
Assembly Components: Trigger Gun, Metal Gun Transfer Adapter, Utility Brush.
Instructions:
- If not already done, detach your spray wand from your trigger gun.
- Attach the transfer adapter to your trigger gun.
- Take the utility brush and align it with the transfer adapter.
- Once aligned, push the utility brush into the transfer adapter and twist to lock into place (follow the arrow in the illustration).
Rotary Wash Brush Assembly Quick Guide
NOTE: These instructions are for connecting with SUN JOE® Pressure Washers only. For connecting with other brands' pressure washers, use the corresponding transfer adapter. Refer to page 2 for details.
For SPX200/SPX1000 Series
Assembly Components: Trigger Gun, Middle Wand, Rotary Brush.
Instructions:
- Disconnect your spray wand assembly so only the middle wand remains attached to your trigger gun.
- Take the rotary wash brush and align it with the middle wand.
- Once aligned, push the rotary wash brush into the middle wand and twist to lock into place (follow the arrow in the illustration).
For SPX2000, SPX2500, SPX2600, SPX4003, SPX4003-ULT
Assembly Components: Trigger Gun, Rotary Brush.
Instructions:
- If not already done, detach your spray wand from your trigger gun.
- Take the rotary wash brush and align it with the inside of the trigger gun.
- Once aligned, push the rotary brush into the trigger gun and twist to lock into place (follow the arrow in the illustration).
For Most SPX2000 Series + SPX4003-ELT, SPX7001E
Assembly Components: Trigger Gun, Rotary Brush.
Instructions:
- If not already done, detach your spray wand from your trigger gun.
- Take the rotary wash brush and align it with the inside of the trigger gun.
- Once aligned, push the rotary brush into the trigger gun and twist to lock into place (follow the arrow in the illustration).
For Most SPX3000 Series + Most SPX4000 Series
Assembly Components: Trigger Gun, Metal Gun Transfer Adapter, Rotary Brush.
Instructions:
- If not already done, detach your spray wand from your trigger gun.
- Attach the transfer adapter to your trigger gun.
- Take the rotary wash brush and align it with your trigger gun.
- Once aligned, push the rotary brush into the transfer adapter and twist to lock into place (follow the arrow in the illustration).
Turbo Nozzle + 20-Inch Rod Assembly Quick Guide
NOTE: These instructions are for connecting with SUN JOE® Pressure Washers only. For connecting with other brands' pressure washers, use the corresponding transfer adapter. Refer to page 2 for details.
WARNING: For safety reasons, the nozzle must be used with the 20-inch rod. For domestic use only. Do not use with commercial grade pressure washers.
For SPX200/SPX1000 Series
Assembly Components: Trigger Gun, Middle Wand, 20-Inch Rod, Turbo Nozzle.
Instructions:
- Disconnect your spray wand assembly so only the middle wand remains attached to your trigger gun.
- Take the 20-inch rod and align it with the middle wand.
- Once aligned, push the 20-inch rod into the middle wand and twist to lock into place (follow the arrow in the illustration).
- Align turbo nozzle and push into the 20-inch rod and twist to lock into place (follow the arrow in the illustration).
For SPX2000, SPX2500, SPX2600, SPX4003, SPX4003-ULT
Assembly Components: Trigger Gun, 20-Inch Rod, Turbo Nozzle.
Instructions:
- If not already done, detach your spray wand from your trigger gun.
- Take the 20-inch rod and align it with the trigger gun.
- Once aligned, push the 20-inch rod into the trigger gun and twist to lock into place (follow the arrow in the illustration).
- Align turbo nozzle and push into the 20-inch rod and twist to lock into place (follow the arrow in the illustration).
For Most SPX2000 Series + SPX4003-ELT, SPX7001E
Assembly Components: Trigger Gun, 20-Inch Rod, Turbo Nozzle.
Instructions:
- If not already done, detach your spray wand from your trigger gun.
- Take the 20-inch rod and align it with the trigger gun.
- Once aligned, push the 20-inch rod into the trigger gun and twist to lock into place (follow the arrow in the illustration).
- Align turbo nozzle and push into the 20-inch rod and twist to lock into place (follow the arrow in the illustration).
For Most SPX3000 Series + Most SPX4000 Series
Assembly Components: Trigger Gun, Metal Gun Transfer Adapter, 20-Inch Rod, Turbo Nozzle.
Instructions:
- If not already done, detach your spray wand from your trigger gun.
- Attach the transfer adapter to your trigger gun.
- Take the 20-inch rod and align the two tabs with the transfer adapter.
- Once aligned, push the 20-inch rod into the metal gun transfer adapter and twist to lock into place (follow the arrow in the illustration).
- Align turbo nozzle and push into the 20-inch rod and twist to lock into place (follow the arrow in the illustration).
Wheel + Rim Brush Assembly Quick Guide
NOTE: These instructions are for connecting with SUN JOE® Pressure Washers only. For connecting with other brands' pressure washers, use the corresponding transfer adapter. Refer to page 2 for details.
For SPX200/SPX1000 Series
Assembly Components: Trigger Gun, Middle Wand, Wheel + Rim Brush.
Instructions:
- Disconnect your spray wand assembly so only the middle wand remains attached to your trigger gun.
- Take the wheel + rim brush and align it with the middle wand.
- Once aligned, push the wheel + rim brush into the middle wand and twist to lock into place (follow the arrow in the illustration).
For SPX2000, SPX2500, SPX2600, SPX4003, SPX4003-ULT
Assembly Components: Trigger Gun, Wheel + Rim Brush.
Instructions:
- If not already done, detach your spray wand from your trigger gun.
- Take the wheel + rim brush and align it with the inside of the trigger gun.
- Once aligned, insert the wheel + rim brush into the trigger gun and twist to lock into place (follow the arrow in the illustration).
For Most SPX2000 Series + SPX4003-ELT, SPX7001E
Assembly Components: Trigger Gun, Wheel + Rim Brush.
Instructions:
- If not already done, detach your spray wand from your trigger gun.
- Take the wheel + rim brush and align it with the inside of the trigger gun.
- Once aligned, insert the wheel + rim brush into the trigger gun and twist to lock into place (follow the arrow in the illustration).
For Most SPX3000 Series + Most SPX4000 Series
Assembly Components: Trigger Gun, Metal Gun Transfer Adapter, Wheel + Rim Brush.
Instructions:
- If not already done, detach your spray wand from your trigger gun.
- Attach the transfer adapter to your trigger gun.
- Take the wheel + rim brush and align it with your trigger gun.
- Once aligned, push the wheel + rim brush into the transfer adapter and twist to lock into place (follow the arrow in the illustration).
51 cm Turbo Nozzle and Extension Wand Assembly Quick Guide
NOTE: These instructions are for connecting with SUN JOE® Pressure Washers only. For connecting with other brands' pressure washers, use the corresponding transfer adapter. Refer to page 18 for details.
WARNING: For safety, the nozzle must be used with the 51 cm extension wand. For domestic use only. Do not use with industrial-grade pressure washers.
For SPX200/SPX1000 Series
Assembly Components: Trigger Gun, Middle Wand, 51 cm Extension Wand, Turbo Nozzle.
Instructions:
- Disconnect the spray wand assembly so only the middle wand remains attached to your trigger gun.
- Take the 51 cm extension wand and align it with the middle wand.
- Once aligned, push the 51 cm extension wand into the middle wand and twist to lock into place (follow the arrow in the illustration).
- Align the turbo nozzle, push it into the 51 cm extension wand, and twist to lock into place (follow the arrow in the illustration).
For SPX2000, SPX2500, SPX2600, SPX4003, SPX4003-ULT
Assembly Components: Trigger Gun, 51 cm Extension Wand, Turbo Nozzle.
Instructions:
- If not already done, detach the spray wand from your trigger gun.
- Take the 51 cm extension wand and align it with the trigger gun.
- Once aligned, push the 51 cm extension wand into the trigger gun and twist to lock into place (follow the arrow in the illustration).
- Align the turbo nozzle, push it into the 51 cm extension wand, and twist to lock into place (follow the arrow in the illustration).
For Most SPX2000 Series + SPX4003-ELT, SPX7001E
Assembly Components: Trigger Gun, 51 cm Extension Wand, Turbo Nozzle.
Instructions:
- If not already done, detach the spray wand from your trigger gun.
- Take the 51 cm extension wand and align it with the trigger gun.
- Once aligned, push the 51 cm extension wand into the trigger gun and twist to lock into place (follow the arrow in the illustration).
- Align the turbo nozzle, push it into the 51 cm extension wand, and twist to lock into place (follow the arrow in the illustration).
For Most SPX3000 Series + Most SPX4000 Series
Assembly Components: Trigger Gun, Metal Gun Transfer Adapter, 51 cm Extension Wand, Turbo Nozzle.
Instructions:
- If not already done, detach the spray wand from your trigger gun.
- Attach the transfer adapter to your trigger gun.
- Take the 51 cm extension wand and align it with the transfer adapter.
- Once aligned, push the 51 cm extension wand into the metal gun transfer adapter and twist to lock into place (follow the arrow in the illustration).
- Align the turbo nozzle, push it into the 51 cm extension wand, and twist to lock into place (follow the arrow in the illustration).
Brush for Wheels and Tires Assembly Quick Guide
NOTE: These instructions are for connecting with SUN JOE® Pressure Washers only. For connecting with other brands' pressure washers, use the corresponding transfer adapter. Refer to page 18 for details.
For SPX200/SPX1000 Series
Assembly Components: Trigger Gun, Middle Wand, Brush for Wheels and Tires.
Instructions:
- Disconnect your spray wand assembly so only the middle wand remains attached to your trigger gun.
- Take the brush for wheels and tires and align it with the middle wand.
- Once aligned, insert the brush for wheels and tires into the middle wand and twist to lock into place (follow the arrow in the illustration).
For SPX2000, SPX2500, SPX2600, SPX4003, SPX4003-ULT
Assembly Components: Trigger Gun, Brush for Wheels and Tires.
Instructions:
- If not already done, detach your spray wand from your trigger gun.
- Take the brush for wheels and tires and align it with the inside of the trigger gun.
- Once aligned, insert the brush for wheels and tires into the trigger gun and twist to lock into place (follow the arrow in the illustration).
For Most SPX2000 Series + SPX4003-ELT, SPX7001E
Assembly Components: Trigger Gun, Brush for Wheels and Tires.
Instructions:
- If not already done, detach your spray wand from your trigger gun.
- Take the brush for wheels and tires and align it with the inside of the trigger gun.
- Once aligned, insert the brush for wheels and tires into the trigger gun and twist to lock into place (follow the arrow in the illustration).
For Most SPX3000 Series + Most SPX4000 Series
Assembly Components: Trigger Gun, Metal Gun Transfer Adapter, Brush for Wheels and Tires.
Instructions:
- If not already done, detach your spray wand from your trigger gun.
- Attach the transfer adapter to your trigger gun.
- Take the brush for wheels and tires and align it with your trigger gun.
- Once aligned, insert the brush for wheels and tires into the trigger gun and twist to lock into place (follow the arrow in the illustration).
Sun Joe® + Sun Joe® Customer Promise & Warranty
Snow Joe, LLC ("Snow Joe") is dedicated to its customers, striving to make every experience pleasant. This document outlines the Limited Warranty for Snow Joe®, Sun Joe®, and Aqua Joe® products.
Our Warranty
Snow Joe warrants new, genuine, powered and non-powered Products to be free from defects in material or workmanship for a period of two years from the date of purchase by the original, end-user purchaser. This warranty does not cover products purchased from unauthorized sellers. If a product or part is defective, Snow Joe will, at its option, send a free replacement part, replace the product with a new or comparable one at no charge, or repair the product.
This warranty grants specific legal rights, and other rights may vary by state.
Product Registration
Snow Joe strongly encourages product registration online at snowjoe.com/register, by mail using a registration card, or by calling Customer Service at 1-866-SNOWJOE (1-866-766-9563), or via email at help@snowjoe.com. Registration does not affect warranty rights but helps Snow Joe provide better customer service.
Who Can Seek Limited Warranty Coverage
This warranty is extended by Snow Joe to the original purchaser and original owner of the Product.
What Is Not Covered?
This warranty does not apply to products used commercially, for non-household or rental applications, or purchased from unauthorized sellers. It also does not cover cosmetic changes that do not affect performance. Wearable parts such as belts, augers, chains, and tines are not covered and can be purchased separately at snowjoe.com or by calling 1-866-SNOWJOE (1-866-766-9563).
