Bistro Bathroom Clear Glass Wall Light

Product Overview

This document provides instructions for the John Lewis Bistro Bathroom Clear Glass Wall Light. It includes specifications, safety information, installation guidance, and care instructions.

Specifications

Recommended bulb: 1 x 5 Watt G9 energy efficient LED

• Max power: 5W
• Voltage: 220~240V, 50/60Hz
• IP Rating: IP44
• Weight: 0.45Kg

[CE certification]

Recycling Information

[recycling symbol] This product should not be treated as normal household waste. John Lewis, as a member of the Distributer Take Back scheme, has funded the development and upgrade of recycling facilities across the UK. Please take it to your nearest collection facility or contact your local council or visit www.recycle-more.co.uk for further details.

Troubleshooting

Why is the light not working when switched on?

• Check your power supply is switched on.
• Turn off light and check that the bulb is inserted correctly.
• Check the bulb is still in working order.

Important Safety Information & Warnings

For your safety, this product must be installed in accordance with local Building Regulations. If in any doubt, consult a competent person registered with an electrical self-certification scheme.

To prevent electric shock, switch off the mains supply before installing or maintaining this product. Ensure others cannot restore the electricity supply without your knowledge.

The external flexible cable or cord of this luminaire cannot be replaced; if the cord is damaged, the luminaire shall be destroyed.

Always use the correct bulb type and wattage as indicated. This product is Class I [earth symbol] and should be fitted to a lighting supply protected by a 5 amp fuse or equivalent circuit breaker.

When changing the bulb, switch off at the mains and allow the old bulb to cool down before handling. Dispose of used bulbs carefully.

This fitting is rated IP44, making it suitable for use in Zones 1 & 2 of a bathroom when fitted in accordance with IEE wiring regulations. Fitting must be connected to a supply protected by a 30mA RCD in Zone 1.

Caution! The bulb and surrounding parts can become hot during use. For indoor use only.

Care Instructions

Clean with a soft dry cloth. Do not use abrasive materials as these will damage the finish.

Replace bulbs from John Lewis or an established brand of the same type and compatibility.

Parts List

Assembly Instructions

Never install on a wet, freshly painted, or plastered surface. Ensure the house electricity supply is switched off at the fuse box. If removing an existing fitting, note down all wiring connections. Check fixings will not touch existing wiring before drilling.

Ensure wall wires are threaded through the black insulating tube fixed to the appliance.

Step 1: Prepare Mounting Bracket

Remove the mounting bracket from the fitting by unscrewing the retaining screws and washers. Use the bracket as a template to mark and drill fixing holes in the wall. Ensure screws are fixed into a solid mounting, not just plasterboard. Take care not to damage wiring. Attach the mounting bracket to the wall surface using suitable fixings. Do not attach the fitting to the bracket yet. Ensure no wires are trapped.

Step 2: Electrical Connections

Lever open the terminal block box cover with a screwdriver. Pierce a hole in the black rubber end cap of the terminal block and feed the supply cable through. Make electrical connections as follows:

• Connect supply live (L) to fitting live (marked "L") on the terminal block.
• Connect supply neutral (N) to fitting neutral (marked "N") on the terminal block.
• Connect the supply earth [earth symbol] to the fitting earth (marked " ").

NOTE: Ensure all electrical connections are tight and no loose strands of wire are left out of the connector block. Excess cable must be carefully located inside the ceiling cup or within the ceiling void.

Step 3: Final Assembly

Carefully locate excess cable inside the wall plate or wall cavity. Offer the fitting over the mounting bracket and secure it in place using the screws and washers removed in Step 1.

Fit the bulb (not supplied), ensuring it is the correct type and wattage as indicated. Do not exceed the maximum wattage. Place the silicone washer over the lamp holder.

Fit the shade: Align the glass shade with the lamp holder section and carefully screw it into place. If cross-threading occurs, undo and restart. Avoid overtightening, which could damage the fitting.

Once installation is complete, restore the house electricity at the fuse box.