tiroli Litesphere 2.0 Light Instruction Manual

Instruction Manual for tiroli models including: Litesphere 2.0 Light, Light

File Info : application/pdf, 15 Pages, 3.00MB

7828-Litesphere 2.0 Installation Instructions 01.17.24 v2

LITESPHERE 2.0

IP67

12V LitesphereTM 2.0 Installation Instructions

PLEASE VERIFY THE CONTENTS OF THE PACKAGES!
PLEASE READ INSTRUCTIONS ENTIRELY BEFORE STARTING INSTALLATION.
BE SURE POWER IS TURNED OFF BEFORE INSTALLING OR MODIFYING THE SYSTEM.

LED Type Standard High Output Very High Output

Maximum Single Run*

6" OC 12" OC 18" OC

130'

180'

230'

80'

110'

130'

30'

55'

70'

24" OC 250' 150' 80'

*Maximum run lengths are based on Tivoli's recommended lumen drop.

CALL TIVOLI LLC TECH SUPPORT WITH QUESTIONS.
Caution: Litesphere 2.0 is designed to work with NRTL listed Class 2 12V DC transformers only. Use of any other power source will cause damage, shorten the life of the fixture and will void the warranty. Consult any and all applicable local and national codes for installation. Do not conceal or extend exposed conductors through a building wall as per local electrical code
Warning: With any luminaire for any application, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injuries. This lighting system should be installed by a certified professional.
Risk of injury or fire. Do not cover any luminaire as the covering may cause it to overheat.
Do not install this lighting system where the exposed bare contacts can be shorted or contact any conductive material to reduce the risk of fire and burns.
Do not install any luminaire closer than 6 inches (15.25cm) from any curtain, or similar combustible material.

Tivoli recommends installing the transformer as close to the light string as possible. Use 12 gauge lead wire and keep the transformer within 80ft of the fixture. Consult factory for lengths over 80ft.
Overview LitesphereTM 2.0 may be cut in the field to match project requirements. Simply cut wires and connect to junction box, or connect directly to transformer for power. Install End Cap (LSL2-EC) on dead end.
Note: Ensure the system is wired for correct polarity. The brown wire connects to the positive (+) terminal, and the blue wire connects to the negative (-) terminal on the power supply.
Note: Prior to installation, it is recommended that each globe be given a firm twist to ensure the Globes are tight after shipping.
Shades: LitesphereTM 2.0 Strands ordered with Shades are shipped with the Globes removed for easier installation of the Shades. Please refer to the installation options for installing LitesphereTM 2.0 with Shades.

Do not use any luminaire if damaged (e.g. broken globe, loose connections, or frayed wire insulation.) Inspect periodically.
Do not submerge any luminaire in liquid. Use waterproof connectors for all outdoor applications.
Do not secure any luminaire with staples, nails or like means that might damage the wire insulation. Secure it by using screws through the base. Do not run any luminaire at an operating temperature exceeding 65° C or 149° F.
Danger of electric shock. Do not cut while system is powered! Measure area where system is to be installed and cut LitesphereTM 2.0 lengths to fit.
Installer must calculate wire size between load and power supply to avoid voltage drop. The wire sizing from the transformer to the light strings must be carefully calculated in order for low voltage circuits to operate properly.

Hanger clip mount to Suspension Cable Illuminate courtyards, streets or parks with festive lighting using Catenary Cable (LS-CABLE 110, and LS-CABLE 500, each sold separately). Each cable is a 1/8" dia. stainless steel aircraft cable. Attach each end of cable to structural support using Cable Locks (LS-LOCK-2) included with 110 foot Cable Kits or available separately. 500 foot cable is not sold with locks and must be ordered individually. Follow instructions carefully.
WARNING: For suspension application, catenary cable is required to support the product, otherwise the warranty will be void.
Note: Article 225.3(B) of the National Electrical Code states that all festoon lighting spans over 40 feet MUST be supported by messenger wire. The messenger wire shall be supported by strain insulators. The LS-CABLE options offered by Tivoli meet these requirements. Consult applicable local codes for installation.

7170804

Page 2 of 15

www.tivolilighting.com tel: 714-957-6101 fax: 714-427-3458

12V LitesphereTM 2.0 Installation Instructions
Option A: Surface Mount

2 3

2x
#6 Screw (by others) (Do not overtighten)

Page 3 of 15

7170804
www.tivolilighting.com tel: 714-957-6101 fax: 714-427-3458

12V LitesphereTM 2.0 Installation Instructions

Option B: Catenary Cable Suspension Cable Preparation

3
Adjusting Catenary Cable
1

Mounting Hardware (by others)
2

Mounting Hardware (by others)
Copyright © 2021 Tivoli 10.19.2021

3
Page 4 of 15

7170804
www.tivolilighting.com tel: 714-957-6101 fax: 714-427-3458

12V LitesphereTM 2.0 Installation Instructions
Option B: Catenary Cable Suspension Torque Adjustments
1

`CLICK'

Option B: Catenary Cable Suspension
1

Page 5 of 15

7170804
www.tivolilighting.com tel: 714-957-6101 fax: 714-427-3458

12V LitesphereTM 2.0 Installation Instructions

Option B: Catenary Cable Suspension
2

Tighten

NOTE: Zip Ties required for every socket.
5

Page 6 of 15

7170804
www.tivolilighting.com tel: 714-957-6101 fax: 714-427-3458

12V LitesphereTM 2.0 Installation Instructions
Option B: Catenary Cable Suspension
6
18"

NOTE: For strands with 18" or greater on center spacing, use a Zip tie in between globes to prevent sagging.

Page 7 of 15

7170804
www.tivolilighting.com tel: 714-957-6101 fax: 714-427-3458

12V LitesphereTM 2.0 Installation Instructions
Installing Light Shade: Shade Assembly
1

NOTE: Make sure gasket is properly seated for a tight fit.

Page 8 of 15

7170804
www.tivolilighting.com tel: 714-957-6101 fax: 714-427-3458

12V LitesphereTM 2.0 Installation Instructions
Installing Light Shade: Shade Assembly to Strand
2

Page 9 of 15

7170804
www.tivolilighting.com tel: 714-957-6101 fax: 714-427-3458

12V LitesphereTM 2.0 Installation Instructions
Installing Light Shade: Globe Installation

NOTE: Make sure gasket is properly seated for water tight seal.

Page 10 of 15

7170804
www.tivolilighting.com tel: 714-957-6101 fax: 714-427-3458

12V LitesphereTM 2.0 Installation Instructions
Removing Excess Globes: Cutting the Strand

Desired Strand Length

Extra

Page 11 of 15

7170804
www.tivolilighting.com tel: 714-957-6101 fax: 714-427-3458

12V LitesphereTM 2.0 Installation Instructions

Removing Excess Globes: Installing End Cap
3
Loosen

Tighten

Page 12 of 15

7170804
www.tivolilighting.com tel: 714-957-6101 fax: 714-427-3458

12V LitesphereTM 2.0 Installation Instructions
Wiring:
Tivoli 12V DC power
supply
+-

Primary line voltage input LN

Electrical Box (If needed)
+-
LitesphereTM 2.0

Page 13 of 15

7170804
www.tivolilighting.com tel: 714-957-6101 fax: 714-427-3458

12V LitesphereTM 2.0 Installation Instructions
LED Bulb Replacement: Globe & LED Removal
1 2

Page 14 of 15

7170804
www.tivolilighting.com tel: 714-957-6101 fax: 714-427-3458

12V LitesphereTM 2.0 Installation Instructions
LED Bulb Replacement: LED Install & Testing

Standard & High Output

Very High Output

NOTE: If an LED does not light up after powering on the Litesphere 2.0 strand, remove unlit LED, flip 180 degrees, and re-insert into socket.

Power

Page 15 of 15

180
7170804
www.tivolilighting.com tel: 714-957-6101 fax: 714-427-3458

References

Tivoli – Over 50 Years of Innovation and Linear Lighting Leadership.

Adobe PDF Library 16.0 Adobe InDesign 16.4 (Windows)