Komfovent VERSO Standard & RHP Standard Outdoor Accessories Installation Guide

General Information and Precautions

VERSO STANDARD air handling units are not suitable for installation in outdoor areas without additional modification. Units intended for outdoor installation must be fixed to a base frame, and air dampers must be installed on the duct connections. The Air Handling Unit (AHU) must be protected from weather influences by installing dedicated roofs and hoods. If possible, it is recommended to install the unit near walls for extra protection from the wind.

Key components shown in diagrams:

• 1: AHU
• 2: Hoods
• 3: Roof
• 4: Base frame
• 5: Air dampers on the room side (recommended)
• 6: Outdoor air closing dampers (mandatory)

Connections of outdoor units must be additionally sealed (sealant not included).

If the outdoor unit is switched off during the cold season, supply and extract air ducts (on the indoor side) must be fitted with additional air shut-off dampers. These should prevent warm indoor air from circulating inside the unit when it is stopped, to avoid condensation, which may be detrimental to electronic components.

Air intake and outlet hoods must be installed as far apart as possible (e.g., by installing additional duct segments between the AHU and the hood) to prevent exhaust air from returning to the air intakes.

Mounting of the Base Frame

This section details the mounting of the base frame for various Komfovent models.

VERSO CF 3500

Step 1: Prepare the base frame components.

Step 2: Assemble the base frame. The diagram shows a frame being assembled, with dimensions indicated (138mm, 180-230mm). It also shows attaching the frame to the unit, with a note that some parts are "Ordered separately".

Step 3: Place the AHU onto the assembled base frame.

Step 4: Secure the AHU to the base frame.

Mounting of the Roofs

This section provides instructions for mounting roofs onto different VERSO and RHP models.

Verso R 1000 - R 1300 - R 1500

Step 1: Assemble the roof structure.

Step 2: Attach the first part of the roof structure to the AHU.

Step 3: Attach the second part of the roof structure.

Step 4: Secure the roof components.

Step 5: Final assembly of the roof.

Verso R 1700 - R 2000 & RHP 800 - 1300 - 1500

Step 1: Assemble the roof structure.

Step 2: Attach the first part of the roof structure to the AHU.

Step 3: Attach the second part of the roof structure.

Step 4: Secure the roof components.

Step 5: Final assembly of the roof.

Verso R 2500 - R 5000 - R 7000

Step 1: Assemble the roof structure.

Step 2: Attach the first part of the roof structure to the AHU.

Step 3: Attach the second part of the roof structure.

Step 4: Attach the third part of the roof structure.

Step 5: Secure the roof components.

Step 6: Final assembly of the roof.

Verso R 3000 - R 4000

Step 1: Assemble the roof structure.

Step 2: Attach the first part of the roof structure to the AHU.

Step 3: Attach the second part of the roof structure.

Step 4: Secure the roof components.

Step 5: Final assembly of the roof.

Verso CF 1000 - CF 1300 - CF 1700

Step 1: Assemble the roof structure.

Step 2: Attach the first part of the roof structure to the AHU.

Step 3: Attach the second part of the roof structure.

Step 4: Secure the roof components.

Step 5: Final assembly of the roof.

Verso CF 2300

Step 1: Assemble the roof structure.

Step 2: Attach the first part of the roof structure to the AHU.

Step 3: Attach the second part of the roof structure.

Step 4: Secure the roof components.

Step 5: Final assembly of the roof.

Verso CF 3500

Step 1: Assemble the roof structure.

Step 2: Attach the first part of the roof structure to the AHU.

Step 3: Attach the second part of the roof structure.

Step 4: Secure the roof components.

Step 5: Final assembly of the roof.

Mounting of the Hoods

This section illustrates the mounting of hoods for various VERSO and RHP models. The diagrams show different configurations for attaching hoods to the respective unit series.

• Verso R 1000 - R 1300 - R 1500 & Verso CF 1000 - CF 1300 - CF 1700
• Verso R 1700 - R 2000
• Verso R 2500 - R 5000 - R 7000
• Verso R 3000 - R 4000 & Verso CF 3500
• Verso CF 2300

Partner and Contact Information

Komfovent provides contact and partner information for various regions:

• Lithuania: UAB KOMFOVENT (Service and Support) with phone and email.
• Russia: ООО «КОМФОВЕНТ» with contact details.
• Belarus: ИООО «Комфовент» with contact details.
• Sweden: Komfovent AB with contact details.
• Finland: Komfovent Oy with contact details.
• Germany: Komfovent GmbH with contact details.
• Latvia: SIA Komfovent with contact details, including a Vidzemes filiāle.

A comprehensive list of international partners is also provided, with their respective countries, company names, and website URLs. These include partners in Austria (AT), Belgium (BE), Czech Republic (CZ), Switzerland (CH), Denmark (DK), Estonia (EE), France (FR), Croatia (HR), Hungary (HU), Ireland (IR), Iceland (IS), Italy (IT), Netherlands (NL), Norway (NO), Poland (PL), Sweden (SE), Slovenia (SI), and Slovakia (SK).