Komfovent VERSO Standard & RHP Standard: Outdoor Accessory Installation Guide

General Information

Komfovent VERSO Standard and RHP Standard air handling units are not suitable for installation in outdoor areas without additional modification. Units intended for outdoor installation must be fixed to a base frame, and air dampers must be installed on the duct connections. The Air Handling Unit (AHU) must be protected from weather influences by installing dedicated roofs and hoods. If possible, it is recommended to install the unit near walls for extra protection from the wind.

Key components mentioned:

1: AHU (Air Handling Unit)
2: Hoods
3: Roof
4: Base frame
5: Air dampers on the room side (recommended)
6: Outdoor air closing dampers (mandatory)

⚠️ Important Notes:

Connections of outdoor units must be additionally sealed (sealant not included).
If the outdoor unit will be switched off during the cold season, supply and extract air ducts (on the indoor side) must be fitted with additional air shut-off dampers. These should prevent warm indoor air from circulating inside the unit when it is stopped, thereby avoiding condensation, which can be detrimental to electronic components.

Air intake and outlet hoods must be installed as far apart as possible (e.g., by installing additional duct segments between the AHU and the hood) to prevent exhaust air from returning to the air intakes.

Note: UAB KOMFOVENT reserves the right to make changes without prior notice.

Mounting of the Base Frame

This section details the installation of the base frame for outdoor units.

For VERSO CF 3500

Assemble the base frame components using the provided fasteners. The diagram shows the frame structure and connection points.
Attach the adjustable feet to the corners of the base frame. The feet are ordered separately. The diagram indicates a height adjustment range of 138-230 mm for the feet. A visual warning symbol (crossed out circle) indicates that lifting equipment should not be attached to the frame's eyelets.
Slide the AHU onto the mounted base frame. An arrow indicates the direction of movement.
Secure the AHU to the base frame using the designated fasteners.

⚠️ Note: It is prohibited to attach lifting equipment to the eyelets (labeled A) on the mounting frame. They are only intended to prevent lifting straps from slipping to the sides.

Mounting of the Roofs

Instructions for mounting roofs on various VERSO models.

For VERSO R 1000 - R 1300 - R 1500

Assemble the roof frame structure using the provided fasteners.
Attach the side panels to the frame.
Attach the roof panels to the frame.
Secure the assembled roof structure to the top of the AHU.
Final assembly of the roof.
Ensure all connections are secure.

For VERSO R 1700 - R 2000

Assemble the roof frame structure.
Attach the roof panels to the frame.
Secure the roof structure to the AHU.
Final check of the roof mounting.

For VERSO R 2500 - R 5000 - R 7000

Assemble the primary roof frame.
Attach side/support elements to the frame.
Attach the first set of roof panels.
Attach the second set of roof panels.
Attach the final roof panels.
Secure the complete roof assembly to the AHU.

For VERSO R 3000 - R 4000

Assemble the roof frame structure.
Attach side panels to the frame.
Attach the first roof panel.
Attach the second roof panel.
Complete the roof assembly and secure it to the AHU.

For VERSO CF 1000 - CF 1300 - CF 1700

Assemble the base frame for the roof structure.
Attach side panels to the frame.
Attach the roof panels to the frame.
Secure the roof structure to the AHU.
Final assembly of the roof.

For VERSO CF 2300

Assemble the base frame for the roof.
Attach side panels.
Attach roof panels.
Secure the roof structure to the AHU.
Final roof assembly.

For VERSO CF 3500

Assemble the roof frame.
Attach side panels.
Attach roof panels.
Secure the roof structure to the AHU.
Final roof assembly.

For VERSO CF 5000

Assemble the roof frame.
Attach side panels.
Attach the first set of roof panels.
Attach the second set of roof panels.
Attach the final set of roof panels.
Secure the complete roof assembly to the AHU.

For VERSO RHP 800 - 1200 - 1600

Assemble the roof frame.
Attach side panels.
Attach roof panels.
Secure the roof structure to the AHU.