Minelab Gold Monster 1000

Quick Start

1. Step 1: Power On

   Press the power button [power button] to turn on the device.

2. Step 2: Automatic Noise Cancel

   The device will automatically cancel noise for approximately 10 seconds (≈ 10 s) to find a stable operating frequency.

3. Step 3: Start Gold Detection

   Begin sweeping the coil over the ground to detect gold.

Control Panel Overview

Indicators

• Gold Prospect Indicator: Shows the likelihood of finding gold.
• Low Battery: ? Indicates when the battery is low.
• Sensitivity Adjustment (1-10): ⚙️ Use these buttons to adjust the sensitivity level from 1 to 10.
• Auto Sensitivity (11): ⚙️ Automatically sets the optimal sensitivity.
• Auto + Sensitivity (12): ⚙️ Automatically adjusts sensitivity and noise cancel.
• Error Indicator: ❌ Shows if there is an error with the device.

Controls

• Volume Adjustment (1-6): ? Use these buttons to set the audio volume from 1 to 6.
• Detection Mode: Select the desired detection mode.
• Power: [power button] Turns the device on or off.

Factory Reset

To reset the device to its factory default settings, press and hold the power button for 10 seconds (≈ 10 s).

Assembly Instructions

1. Step 1: Assemble Shafts

   Screw the lower, middle, and upper shaft sections together. Ensure washers are in place.

2. Step 2: Attach Lower Shaft to Coil

   Connect the lower shaft section to the search coil.

3. Step 3: Attach Control Box to Upper Shaft

   Mount the control box onto the upper shaft section.

4. Step 4: Attach Armrest to Upper Shaft

   Secure the armrest to the upper shaft.

5. Step 5: Route Cable and Connect

   Wrap the cable neatly around the shaft and connect it to the control box.

6. Step 6: Insert Battery

   Insert 8 AA batteries into the battery compartment.

Accessories

Universal Shaft Adapter

This adapter allows the use of alternative plastic shafts or broomsticks (compatible with shafts approximately 22mm to 24.5mm in diameter).

Detection Basics

• Overlapping Sweeps

  Sweep the coil over the ground with overlapping passes to ensure complete coverage.

• Sweep Level

  Maintain a consistent sweep height above the ground for optimal detection.

• Keep Metal Away from Coil

  Avoid bringing metallic objects close to the search coil, as this can cause interference.

• Refill Holes

  After digging a target, remember to refill the hole to restore the ground.

Battery Charging

The device indicates the battery status: charging [charging indicator], fully charged [fully charged indicator], or error [error indicator]. The batteries are rechargeable [rechargeable indicator].

Headphone Connection

Connect headphones to the designated port for audio feedback.

Compliance Information

FCC Part 15.105: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used according to instructions, it may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by reorienting or relocating the receiving antenna, increasing the separation between the equipment and receiver, connecting the equipment into an outlet on a circuit different from that to which the receiver is connected, or consulting the dealer or an experienced radio/TV technician.

Warning: Any changes or modifications not expressly approved by Minelab Electronics could void the user's authority to operate this equipment.

Warranty Information

This product comes with a limited 2-year warranty from the date of purchase. For detailed warranty information, please refer to www.minelab.com. Register your product online at register.minelab.com.

Contact Information

• Australia & Asia Pacific: +61 8 8238 0888, minelab@minelab.com.au
• Europe & Russia: +353 21 423 2352, minelab@minelab.ie
• North, South & Central America: +1 630 401 8150, info@minelabamericas.com
• Middle East & Africa: +971 4 254 9995, minelab@minelab.ae