Minelab MDS-10 Dual Sensor Detector: Operation and Quick Start Guide

Procedimiento para desplegar el MDS-10

1. Extienda el eje inferior

Extend the lower shaft of the detector. This involves pulling out the telescopic sections and securing them.

[Diagram: Shows a person extending a telescopic shaft. Numbered steps indicate pulling sections and locking mechanisms. Icons show a hand pulling and a locking action.]

2. Despliegue el detector

Unfold the main body of the detector. This typically involves rotating and locking different sections into place.

[Diagram: Shows the main detector body being unfolded. Numbered steps indicate pivot points and locking mechanisms. Icons show rotation and locking.]

3. Despliegue la cabeza del sensor

Unfold the sensor head (search coil assembly). This involves extending and securing the arm that holds the coil.

[Diagram: Shows the sensor head assembly being unfolded. Numbered steps indicate pivot points and securing mechanisms.]

4. Coloque el descansabrazo en posición

Position and secure the armrest. This involves attaching it to the main shaft in the designated position.

[Diagram: Shows the armrest being attached to the detector shaft. Numbered steps indicate attachment points and securing the armrest.]

5. Extienda el eje intermedio

Extend the middle shaft. This is another telescopic section that needs to be pulled out and locked.

[Diagram: Shows a person extending another telescopic shaft section. Numbered steps indicate pulling and locking.]

Coloque la batería

Insert the battery pack into the designated compartment. Ensure it is correctly oriented and secured.

[Diagram: Shows the battery compartment with labels a, b, c, d. A checkmark ✔️ indicates correct insertion. The battery pack is shown being inserted into the detector.]

Inicio rápido

1. Encendido

Press the power button ? to turn on the detector. The device will initialize for approximately 5 seconds. Indicator lights will show the status.

[Diagram: Shows the power button being pressed. A timer indicates ~5 seconds. Indicator lights labeled "MD" show successful power-on with green checkmarks ✔️.]

2. Compensación del equipo para detección de metales

Perform coil compensation for metal detection. Hold the search coil 25-50 mm above the ground and sweep it side-to-side over a target area for approximately 8 seconds. Listen for audio feedback ?.

[Diagram: Shows the search coil held at a specific height. A hand icon ✋ indicates the action. The coil is shown sweeping. A timer shows 8 seconds. Musical notes ? indicate audio feedback.]

3. Pieza de prueba para detección de metales

Use a test piece to verify metal detection functionality. Pass the coil over the test piece. A positive detection is indicated by a checkmark ✔️. A non-target object is indicated by a red cross ❌.

[Diagram: Shows a test piece on the ground. The detector coil passes over it, resulting in a positive detection (✔️). Another diagram shows a test piece with a red cross ❌ (not a target) and a green checkmark ✔️ (target).]

4. Compensación del GPR

Perform Ground Penetrating Radar (GPR) compensation. Hold the GPR sensor and move it upwards. Wireless signal icon ? is shown. This process takes approximately 2-3 seconds, indicated by audio feedback ?.

[Diagram: Shows a person holding the detector with GPR sensor. Arrows indicate upward movement. A wireless signal icon ? is displayed. A timer shows 2-3 seconds. Musical notes ? indicate audio feedback.]

5. Pieza de prueba del GPR

Use a GPR test piece to verify GPR functionality. Pass the GPR sensor over the test piece to confirm detection.

[Diagram: Shows a GPR test piece on the ground. The GPR sensor is passed over it, showing a positive detection.]

6. Comience a detectar

Begin detecting by sweeping the detector over the ground.

[Diagram: Shows a person sweeping the detector over the ground, indicating general operation.]

Restablecimiento de fábrica

To perform a factory reset, press and hold the power button for approximately 5 seconds. This will reset the device to its default settings.

[Diagram: Shows a clock icon ⏰ with "~5 sec." next to it. Then, a gear icon ⚙️ and musical notes ? are displayed, indicating the reset process.]

	Minelab MDS-10 Dual Sensor Detector Operations Manual Comprehensive operations manual for the Minelab MDS-10 Dual Sensor Detector, detailing its Metal Detection (MD) and Ground Penetrating Radar (GPR) capabilities for identifying buried threats. Learn about setup, operation modes, safety, and specifications.
	Minelab MDS-10T Dual Sensor Detector Field Guide & Quick Start Comprehensive field guide and quick start instructions for the Minelab MDS-10T Dual Sensor Detector, covering unfolding, setup, and basic operation.
	Minelab MDS-10 Dual Sensor Detector: Metal Detection & GPR Discover the Minelab MDS-10, a robust dual-sensor detector combining Metal Detection (MD) and Ground Penetrating Radar (GPR) for superior detection of ferrous, non-ferrous, and non-metal targets. Features simultaneous multi-frequency technology, UWB impulse radar, and intuitive operation for tactical environments.
	Minelab MDS-10 Dual Sensor Detector: Advanced Metal Detection & GPR Explore the Minelab MDS-10, a powerful Dual Sensor Detector combining Metal Detection (MD) and Ground Penetrating Radar (GPR) for superior performance in target detection. Features rugged design, intuitive interface, and tactical capabilities.
	Minelab Excalibur Metal Detector Instruction Manual Comprehensive instruction manual for the Minelab Excalibur underwater metal detector, covering assembly, controls, operation, maintenance, troubleshooting, and specifications. Learn how to use your Excalibur for effective treasure hunting.
	Minelab X-TERRA ELITE Metal Detector: Quick Start Guide A concise guide to setting up and starting your Minelab X-TERRA ELITE metal detector, covering quick start, search modes, assembly, charging, and control interface. This document is optimized for search engines and accessibility.
	Minelab F3 Compact Mine Detector Field Guide: Unfolding and Operation Comprehensive guide for the Minelab F3 Compact Mine Detector, detailing unfolding procedures, operational steps like switching on, ground balancing, testing, noise cancellation, and volume control.
	Minelab F3 Detektor Mina: Operativni Priručnik Detaljan operativni priručnik za Minelab F3 detektor mina, koji pokriva opis, pripremu, funkcije, radne postupke, održavanje i tehničke podatke. Namijenjen profesionalnoj uporabi u otkrivanju mina.