Industrial WLAN Access Point

Models: AWB5141 (IP30), AWB5142 (IP67)

Product Overview

The Anybus Industrial WLAN Access Points provide robust wireless LAN connectivity for industrial environments. These devices receive and transmit data across various physical levels and connection types, ensuring reliable network communication.

Hardware Description and Connectors

The product line includes two models: AWB5141, designed for indoor use with an IP30 rating, and AWB5142, built for harsher conditions with an IP67 rating.

Mounting Options

AWB5141 (IP30): Designed for mounting on a standard DIN rail using an included DIN clip.
AWB5142 (IP67): Suitable for pole or wall mounting.

Connectors and Pinouts

Antenna Connectors

AWB5141: Features two RP-SMA female connectors for WLAN antennas, labeled ANT 1 WLAN 1 and ANT 2 WLAN 2.
AWB5142: Features two N-type female connectors for WLAN antennas, labeled ANT 1 WLAN 1 and ANT 2 WLAN 2.

RJ45 Ethernet Connector

A standard RJ45 connector is provided for Ethernet connectivity, supporting 10/100 Mbit/s and 1 Gbit/s speeds. The pinout is as follows:

Pin 1: TD+ (DA+)
Pin 2: TD- (DA-)
Pin 3: RD+ (DB+)
Pin 4: (N/C) (DC+)
Pin 5: (N/C) (DC-)
Pin 6: RD- (DB-)
Pin 7: (N/C) (DD+)
Pin 8: (N/C) (DD-)

Power and PoE Connectors

AWB5141: Equipped with power terminals (P+, P-) supporting a wide DC voltage range of 10-60 VDC, with a maximum power consumption of 11.5 W. It also supports 48 VDC Power over Ethernet (PoE) compliant with IEEE 802.3af PD, also with a maximum of 11.5 W.
AWB5142: Features a WAN/PoE port supporting 1 Gbit/s speeds and is PoE enabled according to IEEE 802.3af P.D.

Safety and Compliance Information

General Safety Instructions

Caution: Ensure the power supply is turned off before connecting it to the equipment.
Warning: Connecting power with reverse polarity or using the wrong type of power supply may damage the equipment. Ensure the power supply is connected correctly and is of the recommended type.
ESD Protection: This equipment contains parts susceptible to electrostatic discharge (ESD). Use ESD prevention measures to avoid damage.
Grounding: To prevent system damage, the equipment must be connected to ground.

Intended Use

The intended use of this equipment is to provide wireless LAN connectivity. It receives and transmits data on various physical levels and connection types. If used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.

Radio Regulations

To comply with the European Radio Equipment Directive (RED) and local radio regulations, country/region settings must be configured before the equipment is put into use. Refer to the user manual for detailed instructions on configuring these settings.

Installation Guidelines

AWB5141 IP30 Version Installation

Mount the device on a standard DIN rail using the included DIN clip.
Establish a direct connection between the ground screw and a grounding surface.
Connect the antennas.
Connect the Ethernet cable.
Connect the power supply via Ethernet or using the included plug connector.

AWB5142 IP67 Version Installation

Mount the device on a pole or wall.
Connect the antennas.
Connect the Ethernet cable.
Connect the power supply via Ethernet.

Refer to the user manual for further detailed instructions.

Technical Specifications

Feature	AWB5141	AWB5142
Order Codes	WLAN AP, IP30, with mesh	WLAN AP, IP67, with mesh
Ethernet Connector	RJ45
Power Supply	10-60 VDC (terminal block) or IEEE 802.3af (48 VDC PoE) Max. 11.5 W	IEEE 802.3af (48 VDC PoE) Max. 11.5 W
WLAN 2.4 GHz Max RF Transmitted Power	IEEE 802.11b: 21 ±2 dBm IEEE 802.11g: 22 ±2 dBm IEEE 802.11n: 21 ±2 dBm
WLAN 5 GHz Max RF Transmitted Power	IEEE 802.11a: 21.5 ±2 dBm IEEE 802.11an: 21.5 ±2 dBm IEEE 802.11ac: 21.5 ±2 dBm
Dimensions (W x H x D)	200 x 51 x 126 mm (without DIN mounting clip)	269 x 239 x 68 mm (without bracket)
Weight	660 g	2400 g
Housing Material	Metal
IP Protection Class	IP30	IP67
Mounting	DIN rail mount	Pole/Wall mount
Operating Temperature	-40 °C to 70 °C, 5–95 % RH non-condensing

Additional technical data and information related to the installation and use of this product can be found at www.anybus.com/support.

Compliance and Certifications

CE Compliance

This product is in compliance with the Radio Equipment Directive 2014/53/EU and the RoHS Directive 2011/65/EU with amendment 2015/863, through conformance with applicable standards. The full text of the Declaration of Conformity is available at www.anybus.com/support.

FCC Compliance

This product contains FCC ID: 2ACNTAWB51415142.

UL Ordinary Locations (OrdLoc) Certification

This equipment is certified for use in ordinary locations in compliance with the following standards:

CAN/CSA-C22.2 No. 62368-1-14
BS EN 62368-1:2014+A11:2017
UL62368-1
AS/NZS 62368.1:2018
IEC 62368-1:2014 (ED. 2.0)
J62368-1 (H30) Japanese Language - AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS

The certification number for Anybus Infrastructure products according to OrdLoc certification is: E514162.

According to the standards listed above, Anybus Industrial WLAN/LTE Routers are certified with the following marking.

Disposal and Recycling

Proper disposal of this equipment is required according to local laws and regulations. As it contains electronic components, it must be disposed of separately from household waste. When the equipment reaches its end of life, contact local authorities for disposal and recycling options, or return the equipment to HMS. For more information, see www.hms-networks.com.

	Anybus CompactCom 40 EtherCAT Network Guide Comprehensive network guide for the Anybus CompactCom 40 EtherCAT communication module by HMS Networks, detailing features, operation, and implementation for industrial automation applications.
	Anybus Wireless Bolt RJ45 PoE Startup Guide - HMS Networks Get started with the Anybus Wireless Bolt RJ45 PoE by HMS Networks. This guide covers installation, configuration, safety, and technical specifications for reliable industrial wireless connectivity.
	Anybus CompactCom 40 DeviceNet Network Guide Comprehensive guide detailing the features, operation, and technical specifications of the Anybus CompactCom 40 DeviceNet communication module for industrial automation networks. Includes information on CIP objects, DeviceNet implementation, and host application integration.
	Anybus CompactCom 40 PROFINET IRT IIoT Secure Network Guide \| HMS Industrial Networks Explore the Anybus CompactCom 40 PROFINET IRT IIoT Secure from HMS Industrial Networks. This network guide details its features, setup, configuration, and integration for industrial IIoT applications, including PROFINET, OPC UA, and MQTT.
	ProfiHub A5 User Manual - Industrial PROFIBUS DP Repeater by Anybus (HMS Networks) This user manual provides detailed information on the Anybus ProfiHub A5, a 5-channel PROFIBUS DP spur and repeater component. It covers product features, application areas, installation instructions, technical specifications, and troubleshooting for industrial automation networks.
	Connect Anybus CompactCom to IIoT Applications Using Node-RED This application note from HMS Industrial Networks AB guides users on integrating Anybus CompactCom devices with Node-RED for IIoT applications, providing practical examples for data access and filtering.
	Anybus Wireless Bridge II: Industrial Ethernet Bluetooth & WLAN Connectivity Datasheet for the Anybus Wireless Bridge II (AWB3000, AWB3010) by HMS Networks. Features robust industrial Ethernet connectivity via Bluetooth and WLAN, ideal for hazardous or hard-to-reach locations. Includes technical specifications, features, and certifications.
	AnyBus-X J1939 to Modbus Interface User Manual User manual for the AnyBus-X J1939 to Modbus Interface, detailing installation, configuration, operation, and specifications for connecting J1939 heavy-duty vehicle networks with Modbus RTU master devices.