Technical support for HMS products | HMS Networks
User Guide for Anybus models including: AWB2030, Wireless Bolt RJ45 PoE
The configuration settings are described in detail in the User Manual. Anybus Wireless Bolt ™ RJ45 PoE Startup Guide SP2359 1.4 en-US Configuration 11 (16)
See the Anybus Wireless Bolt RJ45 PoE User Manual for more information. Anybus Wireless Bolt™ RJ45 PoE Startup Guide. SP2359 1.4 en-US. Page 6 ...
Installation 6 (16) 2.3 Mechanical Installation Placement • The device is intended to be mounted on top of a machine or cabinet through an M50 (50.5 mm) hole using the included sealing ring and nut.
File Info : application/pdf, 16 Pages, 1.46MB
DocumentDocumentAnybus® Wireless BoltTM RJ45 PoE STARTUP GUIDE SP2359 1.4 en-US ENGLISH Important User Information Disclaimer The information in this document is for informational purposes only. Please inform HMS Networks of any inaccuracies or omissions found in this document. HMS Networks disclaims any responsibility or liability for any errors that may appear in this document. HMS Networks reserves the right to modify its products in line with its policy of continuous product development. The information in this document shall therefore not be construed as a commitment on the part of HMS Networks and is subject to change without notice. HMS Networks makes no commitment to update or keep current the information in this document. The data, examples and illustrations found in this document are included for illustrative purposes and are only intended to help improve understanding of the functionality and handling of the product. In view of the wide range of possible applications of the product, and because of the many variables and requirements associated with any particular implementation, HMS Networks cannot assume responsibility or liability for actual use based on the data, examples or illustrations included in this document nor for any damages incurred during installation of the product. Those responsible for the use of the product must acquire sufficient knowledge in order to ensure that the product is used correctly in their specific application and that the application meets all performance and safety requirements including any applicable laws, regulations, codes and standards. Further, HMS Networks will under no circumstances assume liability or responsibility for any problems that may arise as a result from the use of undocumented features or functional side effects found outside the documented scope of the product. The effects caused by any direct or indirect use of such aspects of the product are undefined and may include e.g. compatibility issues and stability issues. Anybus® Wireless BoltTM RJ45 PoE Startup Guide SP2359 1.4 en-US Preparation 3 (16) 1 Preparation 1.1 About This Document This document describes how to install Anybus Wireless Bolt RJ45 PoE and set up a basic configuration. For additional documentation, configuration examples, FAQs, troubleshooting guides and technical support, please visit www.anybus.com/support. 1.2 Document Conventions The following conventions are used to indicate safety information and other important content in this document: WARNING Instruction that must be followed to avoid a risk of death or serious injury. Caution Instruction that must be followed to avoid a risk of personal injury. Instruction that must be followed to avoid a risk of reduced functionality and/or damage to the equipment, or to avoid a network security risk. Additional information which may facilitate installation and/or operation. 1.3 Trademarks Anybus® is a registered trademark and Wireless BoltTM is a trademark of HMS Industrial Networks AB. All other trademarks mentioned in this document are the property of their respective holders. Anybus® Wireless BoltTM RJ45 PoE Startup Guide SP2359 1.4 en-US Preparation 4 (16) 1.4 Intended Use This equipment is intended to provide wireless communication over WLAN and Bluetooth® to wired networks. Typical applications for this equipment: · Adding wireless cloud connectivity to industrial devices · Accessing devices from a laptop, smartphone or tablet · Ethernet cable replacement between devices Note: Bluetooth PAN (Personal Area Network) may not work with some devices due to different implementations of Bluetooth by different manufacturers. WLAN 5 GHz cannot be used at the same time as WLAN 2.4 GHz or Bluetooth. 1.5 Type Identification The type name consists of a type prefix followed by two designators for interface configuration and functionality. Prefix Interface configuration Functionality AWB2 A B A B C Anybus Wireless Bolt Interface 18-pin socket Interface RJ45 and 3-pin power socket Ethernet Ethernet and RS232/485 Ethernet and CAN Example: AWB2AA = Anybus Wireless Bolt with18-pin plug connector and Ethernet networking only. Anybus® Wireless BoltTM RJ45 PoE Startup Guide SP2359 1.4 en-US Installation 5 (16) 2 Installation 2.1 General Safety Instructions Caution This equipment emits RF energy in the ISM (Industrial, Scientific, Medical) band. Make sure that all medical devices used in proximity to this equipment meet appropriate susceptibility specifications for this type of RF energy. This equipment is recommended for use in both industrial and domestic environments. For industrial environments it is mandatory to use the functional earth connection to comply with immunity requirements. For domestic environments the functional earth must be used if a shielded Ethernet cable is used, in order to meet emission requirements. This equipment contains parts that can be damaged by electrostatic discharge (ESD). Use ESD prevention measures to avoid damage. 2.2 General Information Make sure that you have all the necessary information about the capabilities and restrictions of your local network environment before installation. For optimal reception, wireless devices require a zone between them clear of objects that could otherwise obstruct or reflect the signal. A minimum distance of 50 cm between the devices should also be observed to avoid interference. The characteristics of the antenna should also be considered when choosing the placement and orientation of the unit. See the Anybus Wireless Bolt RJ45 PoE User Manual for more information. Anybus® Wireless BoltTM RJ45 PoE Startup Guide SP2359 1.4 en-US Installation 6 (16) 2.3 Mechanical Installation Placement · The device is intended to be mounted on top of a machine or cabinet through an M50 (50.5 mm) hole using the included sealing ring and nut. · The top mounting surface, in contact with the sealing, must be flat with a finish equivalent to Ra 3.2 or finer and cleaned and free from oils and greases. · For optimal reception, wireless devices require a zone between them clear of objects that could otherwise obstruct or reflect the signal. To avoid interference, a minimum distance of 50 cm between Wireless Bolt RJ45 PoE and other devices should be observed. Make sure that the sealing ring is correctly placed in the circular groove in the top part of the housing before tightening the nut. Always hold the BOTTOM part of the unit when untightening the nut, not the top part (the cap). Tightening torque: 5 Nm ±10 % All measurements are in mm. Anybus® Wireless BoltTM RJ45 PoE Startup Guide SP2359 1.4 en-US Installation 7 (16) 2.4 Connectors Connecting power with reverse polarity or using the wrong type of power supply may damage the equipment. Make sure that the power supply is connected correctly and of the recommended type. See also Technical Data, p. 14 regarding power supply requirements. Power Connector (3-pin terminal block) Pin Function 1 2 + - 1936 VDC 3 Functional Earth (FE) FE must be connected on the power connector if not using PoE. Ethernet Connector (RJ45 PoE) Pin 1 2 3 4 5 6 7 8 Housing Data TD+ TDRD+ RD- Shield PoE A+ A+ Positive power from alt. A PSE A- Negative power from alt. A PSE (with pin 6) B+ B+ Positive power from alt. B PSE A- Negative power from alt. A PSE (with pin 3) BB- Negative power from alt. B PSE Functional Earth (FE) via 1 nF capacitor and 1 M bleeder resistor Shielded or unshielded Ethernet cables may be used. Anybus® Wireless BoltTM RJ45 PoE Startup Guide SP2359 1.4 en-US Installation 8 (16) 2.5 RJ45 LED Indicators LED A LINK/ACTIVITY Off Yellow Yellow, flashing LED B STATUS Off Blue Purple Blue, slow blink Alternating blue/purple Purple, slow blink Purple, fast blink Red, slow blink Red Function No Ethernet link or no power Ethernet link established Ethernet traffic Function No power Connected on all configured wireless interfaces Trying to connect to WLAN/Bluetooth access point Awaiting connections Connected on one interface and trying to connect or awaiting connections on another Awaiting connections on one interface and trying to connect on another Scanning for Bluetooth devices or WLAN networks No configured wireless interface Recoverable/unrecoverable fault Anybus® Wireless BoltTM RJ45 PoE Startup Guide SP2359 1.4 en-US Installation 9 (16) 2.6 RESET Button The RESET button is located on the bottom of the unit. When the unit is powered on, press and hold RESET for >10 seconds and then release it to reset to the factory default settings. Recovery Mode If the web interface cannot be accessed, the unit can be reset by starting in Recovery Mode and reinstalling the firmware using Anybus Firmware Manager II, which can be downloaded from www.anybus.com/support. To enter Recovery Mode, press and hold RESET during startup. Firmware updates should normally be carried out through the web interface. Recovery Mode should only be used if the unit is unresponsive and the web interface cannot be accessed. Anybus® Wireless BoltTM RJ45 PoE Startup Guide SP2359 1.4 en-US Configuration 10 (16) 3 Configuration Anybus Wireless Bolt RJ45 PoE is configured via a web interface. Parameters can be set individually or using pre-configured Easy Config modes. Advanced configuration can be carried out by issuing AT commands via the web interface or over a Telnet or RAW TCP connection to port 8080. 3.1 Web Interface The web interface is accessed by pointing a web browser to the IP address of the unit. The default address is 192.168.0.99. The configuration settings are described in detail in the User Manual. Anybus® Wireless BoltTM RJ45 PoE Startup Guide SP2359 1.4 en-US Configuration 11 (16) 3.2 Easy Config Modes By default Wireless Bolt RJ45 PoE starts in Easy Config mode 4, when: · the Ethernet connection is not used · connected to power · factory default settings are used EC Role Description 1 Bluetooth PANU Configure as Bluetooth client and scan for another client (PANU to PANU). 2 3 Reset configuration to factory defaults. Reset IP settings to factory defaults. 4 Client 5 WLAN AP 6 Bluetooth NAP Wait for automatic configuration. Configure units in mode 4 as clients. When mode 4 is used with mode 1, 6 or 7, Serial Settings TCP Mode Client is activated automatically. Configure units in mode 4 as clients. Restart as access point and connect clients. 7 WLAN AP 8 Bluetooth NAP Configure units in mode 4 as clients. Restart as access point and connect clients. Apply PROFINET optimization to all units. 9 Bluetooth PANU Configure as Bluetooth client and scan for another client (PANU to PANU). Apply PROFINET optimization to both units. 10 (any) Apply PROFINET optimization and restart. 11 (any) Enable PROFIsafe mode. The Easy Config modes are also described when selected in the web interface. 3.3 I/O-Data Cycle Time Based on recommendations from industrial equipment suppliers, such as Rockwell and Siemens, it is recommended to use the following minimum I/Odata cycle times for PROFINET and EtherNet/IP networks: · Wireless link Point-to-Point with Bluetooth PANU-PANU or Wi-Fi Access Point to Station: 32 ms · Wireless link with Access Point and up to 4 wireless clients/stations, Bluetooth or Wi-Fi: 64 ms Anybus® Wireless BoltTM RJ45 PoE Startup Guide SP2359 1.4 en-US Configuration 3.4 Factory Restore Any one of these actions will restore the factory default settings: · Clicking on Factory Restore on the System Settings page · Executing Easy Config Mode 2 · Issuing the AT command AT&F and then restarting the unit · Holding RESET pressed for >10 seconds and then releasing it Default Network Settings IP Assignment IP Address Subnet Mask Default Gateway Internal DHCP Server DHCP Interfaces Static 192.168.0.99 255.255.255.0 192.168.0.99 Disabled All Default WLAN Settings Operating Mode Channel Bands Authentication Mode Channel Bridge Mode Client 2.4 GHz & 5 GHz WPA/WPA2PSK Auto Layer 3 IP forward Default Bluetooth Settings Operating Mode Local Name Connectable Discoverable Security Mode Bluetooth LE PANU (Client) [generated from MAC address] No No Just works Operating Mode: Disabled Connectable: No Discoverable: No 12 (16) Anybus® Wireless BoltTM RJ45 PoE Startup Guide SP2359 1.4 en-US Configuration 13 (16) 3.5 Configuration Examples 3.5.1 Ethernet Bridge via WLAN or Bluetooth® (Easy Config) This example describes how to connect two Ethernet network segments via WLAN or Bluetooth using Easy Config. 1. In the web interface of unit 1, activate Easy Config Mode 4. This unit will now be discoverable and open for automatic configuration. 2. In the web interface of unit 2, activate Easy Config Mode 5 for WLAN or 6 for Bluetooth. Unit 2 will now discover and configure unit 1 as a client and configure itself as an access point. Unit 1 will be assigned the first free IP address in the same Ethernet subnet as unit 2. Adding More Devices Up to 6 additional clients can be added by repeating the procedure. Each new client will be assigned the next free IP address in the current subnet. Anybus® Wireless BoltTM RJ45 PoE Startup Guide SP2359 1.4 en-US Technical Data 14 (16) 4 Technical Data For complete technical specifications and regulatory compliance information please visit www.anybus.com/support. 4.1 Hardware Specifications Order code Color Wired interface type Ethernet connector Power connector Antenna Maximum range Operating temperature Storage temperature Humidity Vibration Dimensions Weight Housing material Protection class Mounting Power supply Power over Ethernet Power consumption AWB2030 Black AWB2031 White top and black base Ethernet RJ45 3-pole screw connector Internal dual-band 2.4 GHz and 5 GHz antenna 100 m (WLAN and Bluetooth) Shadow: -40 to +65 °C Direct sunlight: -40 to +45 °C Shadow: -40 to +65 °C Direct sunlight: -40 to +65 °C -40 to +85 °C EN 600068-2-78: Damp heat, +40°C, 93% humidity for 4 days. See datasheet Height: 75 mm (84 mm with PS connector) Outside height: 41 mm Diameter: 68 mm 84 g Plastic (see datasheet for details) Top (outside of host): IP66 / IP67 / UL NEMA 4X Base (inside of host): IP21 M50 screw and nut (50.5 mm hole needed) 1936 VDC 4457 VDC DTE Type1 according to IEEE 802.3af 0.7 W idle, 1.7 W max. Anybus® Wireless BoltTM RJ45 PoE Startup Guide SP2359 1.4 en-US This page intentionally left blank last page © 2020 HMS Industrial Networks Box 4126 300 04 Halmstad, Sweden info@hms.se SP2359 1.4 en-US / 2020-11-30 / 20884