Installation Guide for APS models including: IB-210C, IB-210H, IB-210C iBoard Series Step Bar, iBoard Series Step Bar, Step Bar, Bar
Auto Parts & Auto Accessories - Over 4000 Auto Parts, Aftermarket Parts, Truck Accessories & Car Accessories
PART#: IB-210C&H iBoard® Series READ INSTRUCTIONS CAREFULLY BEFORE START ING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED. *BODY FRAME MOUNT *NO DRILLING REQUIRED Fastener Size 6mm 8mm 10mm 12mm 7/16" Tightening Torque (ft-lbs) 6-7 16-18 31-32 56-58 47-49 Required X PART LIST Driver Side Step Bar Front Passenger Side Step Bar Driver Front Mounting Bracket (DFM) Passenger Front Mounting Bracket (PFM) Driver Rear Bar Bracket (DRB/ PRB) Driver/Passenger Rear Support Bracket (DRS/PRS) Driver/Passenger Rear Mounting Bracket 1 (DRM1/PRM1) Driver/Passenger Rear Mounting Bracket (DRM/PRM) Customer Support: info@iboardauto.com 1 Passenger Rear Bar Bracket (DRB/ PRB) Rev. 20250301 Item QTY Hardware Package A (For Bracket Installation) Description Item QTY Description 1# 2 32 Tube Spacers 8# 12 M12 Flat Washers 2# 2 7/16"-20 x 1.75" Fine Thread Coupling Nuts 9# 8 M12 Lock Washers 3# 2 7/16"-14 x 1.75" Coarse Thread Coupling Nuts 10# 4 M12X1.75 Hex Nuts 4# 2 7/16"-20 Hex Bolts 11# 2 M8X1.25-25mm Hex Bolts 5# 2 7/16"-14 Hex Bolts 12# 4 M8 Large Flat Washers 6# 2 M10X1.5-25mm Hex Bolts 13# 2 M8 Lock Washers 7# 4 M12X1.75-35mm Hex Bolts 14# 2 M8X1.25 Hex Nuts 1 # 2 # 3 # 4# 5# 6# 7 # 8# 9# 10# 11# 12# 13# 14# Hardware Package B (For Stainless Steel Step Bar Installation) Item QTY Description Item QTY Description 1# 8 M8X1.25-35mm Carriage Bolts 3# 8 M8 Nylon Lock Nuts 2# 8 M8 Large Flat Washers 4# 4 Sliders (Packed with Step Bars) 1 # 2 # 3 # 4 # Customer Support: info@iboardauto.com 2 Rev. 20250301 STEP 1 Starting under the passenger side of the vehicle, locate the factory front body mount, (Fig 1). Select (1) 7/16''-14 Coarse Thread Coupling Nut. Thread the Coupling Nut onto the exposed end of the body mount bolt, (Fig 2). Tighten hardware at this time. IMPORTANT: The hardware kit includes (4) Coupling Nuts, (2) 7/16"-14 Hex Bolts and (2) 7/16"-20 Hex Bolts. Verify that you have selected the coarse thread Coupling Nut or damage to the body mount bolt or Coupling Nut may result. Front Body Mount STEP 2 Select Passenger Front Mounting Bracket (PFM) and (1) 32 Tube Spacer. Slide the 32 Tube Spacer over the Coupling Nut, (Fig 3). Hold the Front Mounting Bracket in position against the Coupling Nut and Spacer. Secure the Bracket to the Coupling Nut with (1) 7/16"-14 Hex Bolt, (1) M12 Flat Washer and (1) M12 Lock Washer. IMPORTANT: Verify that you have selected the coarse thread 7/16"-14X1.75" Hex Bolt or damage to the Coupling Nut may result. Do not fully tighten hardware at this time. Front 32 Tube Space Front (Fig 1) Passenger Side Front Mounting Location Thread the 7/16" 14 Coarse Thread Coupling Nut onto threaded end of body bolt Front (Fig 2) 7/16"-14 Coarse Thread Coupling Nut Installation (1) 7/16"-14 Hex Bolt (1) M12 Flat Washer (1) M12 Lock Washer (Fig 3) Passenger Front Mounting Bracket (PFM) Installation STEP 3 Move to Passenger Side Rear Mounting Location. Select (1) Passenger Rear Mounting Bracket (DRM/PRM). Thread (1) M10X1.5-25mm Hex Bolt into the hex nut welded onto the Bracket. Slide the Bracket onto the bottom of the frame rail, (Fig 4). Select (1) Passenger Rear Mounting Bracket 1 (DRM1/PRM1). Bolt it to the Passenger Rear Mounting Bracket (DRM/PRM) with (1) M12x1.75-35mm Hex Bolt, (2) M12 Flat Washers, (1) M12 Lock Washer and (1) M12x1.75 Hex Nut, (Fig 5). Do not fully tighten hardware at this time. Note: Loosen M10X1.5-25mm Hex Bolt in Passenger Rear Mounting Bracket (DRM/PRM) to slide Assembly Bracket forward or backward on frame channel to line up with the end of Customer Support: info@iboardauto.com 3 Rev. 20250301 the Running Board. Once properly lined up, tighten M10X1.525mm Hex Bolt. DRM/PRM STEP 4 Select a Passenger Rear Bar Bracket (DRB/PRB) and attach to the Passenger Rear Mounting Bracket 1 (DRM1/PRM1) with (1) M12x1.75-35mm Hex Bolt, (2) M12 Flat Washers, (1) M12 Lock Washer and (1) M12x1.75 Hex Nut. (Fig 6 & 9). Do not fully tighten hardware at this time. M10x1.5-25mm Hex Bolt (Fig 4) Passenger Rear Mounting Bracket (DRM/PRM) Installed (1) M12x1.75-35mm Hex Bolt (2) M12 Flat Washers (1) M12 Lock Washer (1) M12x1.75 Hex Nut DRM/PRM DRM1/PRM1 Rear (Fig 5) Passenger Rear Mounting Bracket 1 Installed DRM/PRM (1) M12x1.75-35mm Hex Bolt (2) M12 Flat Washers (1) M12 Lock Washer (1) M12x1.75 Hex Nut STEP 5 Locate the exposed threaded end of the outer seat belt bolt in the bottom of the floor panel, (Fig 7). Select (1) 7/16"-20 Fine Thread Coupling Nut. Thread the Coupling Nut onto the threaded end of the seat belt bolt. Tighten the Coupling Nut. Select (1) Passenger Rear Support Bracket (DRS/PRS). Bolt the Support Bracket to the Coupling Nut with (1) 7/16"-20 Hex Bolt, (1) M12 Flat Washer and (1) M12 Lock Washer, (Fig 8). Then bolt the Passenger Rear Support Bracket (DRS/PRS) to the Passenger Rear Bar Bracket (DRB/PRB) with (1) M8X1.2520mm Hex Bolt, (2) M8 Flat Washers, (1) M8 Lock Washer and (1) M8x1.25 Hex Nut, (Fig 9). IMPORTANT: Verify that you have selected the 7/16-20 Hex Bolt or damage to the Bolt or Coupling Nut may result. Do not fully tighten hardware at this time. Thread the 7/16" 20 Fine Thread Coupling Nut onto threaded end of seat belt bolt Rear Rear DRM1/PRM1 DRB/PRB (Fig 6) Passenger Rear Bar Bracket Installed (Fig 7) Thread The 7/16" 20 Fine Thread Coupling Nut Onto Threaded End Of Seat Belt Bolt Customer Support: info@iboardauto.com 4 Rev. 20250301 Rear DRS/PRS 7/16" 20 Fine Thread Coupling Nut 7/16" 20 Hex Bolt M12 Flat Washer M12 Lock Washer (Fig 8) Passenger Rear Support Bracket Installation (Fig 9) Passenger Side Rear Brackets Assembly STEP 6 Once all (2) Passenger side mounting brackets are installed, then proceed to the Step Bar installation. (Figs 10 & 11) (1) Select (1) Slider and (2) M8X1.25-35mm Carriage Bolts; (2) Install (2) M8X1.25-35mm Carriage Bolts in (1) Slider. (3) Slide the Slider (with carriage bolts) to the Step Bar. (4) Repeat to install the other (1) slider to the step bar. (5) Attach the Step Bar (with the Sliders) onto the installed mounting brackets. Position the Sliders to the installed brackets. Secure the Step Bar to the installed Brackets by using (4) M8 Large Flat Washers and (4) M8 Nylon Lock Nuts and (2) Sliders, (Fig 11). Do not fully tighten hardware at this time. Note: The Sliders are packed with the Step Bars. Level and adjust the Step Bar and fully tighten all hardware. Repeat Steps 1-6 for the other side Step Bar installation. The installation is completed!!! DRS/PRS DRB/PRB DRM/PRM (2) M12x1.75-35mm Hex Bolt (4) M12 Flat Washers (2) M12 Lock Washer (2) M12x1.75 Hex Nut DRM1/PRM1 (1) M8x1.25-25mm Hex Bolt (2) M8 Flat Washers (1) M8Lock Washer (1) M8x1.25 Hex Nut Customer Support: info@iboardauto.com 5 Rev. 20250301 Slider (2) Carriage Bolts (Fig 10) Slider Installation Slider with (2) Carriage Bolts Step Bar Slider (w/ installed Carriage Bolts) Step Bar (Bottom View) Mounting Bracket (2) M8 Large Flat Washers (2) M8 Nylon Lock Nuts (Fig 11) Step Bar Installation Attention Do periodic inspections to the installation to make sure that all hardware is secure and tight. In order to protect your bars/boards, please use mild soap/non-abrasive products for cleaning only. Customer Support: info@iboardauto.com 6 Rev. 20250301Microsoft Publisher 2016