T730 600M Rechargeable Remote Training Collar

Thank you for choosing our product. You can sync the remote transmitter and collar receiver to operate spray/vibration function to discourage your dog from unwanted behaviors and effectively train your dog at a long distance.

IMPORTANT SAFETY INFORMATION

Explanation of Attention Words and Symbols used in this User Manual:

• ⚠️ This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

• WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.

• CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

• CAUTION, used without the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in harm to your pet.

WARNING

Not for use with aggressive dogs. Do not use this product if your dog is aggressive, or if your dog is prone to aggressive behavior. Aggressive dogs can cause severe injury and even death to their owner and others. If you are unsure whether this product is appropriate for your dog, please consult your veterinarian or certified trainer.

Do not puncture or incinerate the collar or the refill cannister. Do not expose to extreme heat or store at temperatures above 113 °F or 45 °C.

Lithium Rechargeable Batteries: This device contains Lithium-Polymer (Li-Polymer) batteries; never incinerate, puncture, deform, short-circuit, or charge with an inappropriate charger. Fire, explosion, property damage, or bodily harm may occur if this warning is not followed.

Do not expose the device to freezing temperatures (32 °F or 0 °C) or to conditions warmer than 113 °F or 45°C. Do not leave the collar in direct sunlight. Never leave the collar in a car where the device can heat up to high temperatures (113 °F or 45 °C).

• Contains gas under pressure; may explode if heated.
• Wear protective gloves / eye protection / face protection.
• Do not breathe dust / fume / gas/mist / vapors / spray.
• In case of inadequate ventilation, wear respiratory protection.
• If exposed or concerned: Get medical advice / attention.
• Protect from sunlight. Store in a well-ventilated place. Do not puncture. Do not burn.
• Keep out of reach of children.

FIRST AID TREATMENT:

If inhaled, get medical attention if you feel unwell. After skin contact, rinse affected area with soap and water. After eye contact, rinse/flush eyes gently using water for 15-20 minutes.

CAUTION

This product is not a toy. Keep it away from the reach of children.

CAUTION

Risk of skin damage. Please read and follow the instructions in this manual. Proper fit of the collar is important. A collar worn for too long or made too tight on the pet's neck may cause skin damage. Ranging from redness to pressure ulcers; this condition is commonly known as bed sores.

• Avoid leaving the collar on the dog for more than 12 hours per day.
• When possible, reposition the collar on the pet's neck every 1 to 2 hours.
• Check the fit to prevent excessive pressure; follow the instructions in this manual.
• Never connect a leash to the electronic collar.
• When using a separate collar for a leash, don't put pressure on the electronic collar.
• Wash the dog's neck area and the contact area of the collar weekly with a damp cloth.
• Examine the contact area daily for signs of a rash or a sore.
• If a rash or sore is found, discontinue use of the collar until the skin has healed.
• If the condition persists beyond 48 hours, see your veterinarian.

These steps will help keep your pet safe and comfortable. Millions of pets are comfortable while they wear smooth contacts. Some pets are sensitive to contact pressure. You may find after some time that your pet is very tolerant of the collar. If so, you may relax some of these precautions. It is important to continue daily checks of the contact area. If redness or sores are found, discontinue use until the skin has fully healed.

This Remote Spray Trainer must be used only on healthy dogs. We recommend that you take your dog to a veterinarian before using the collar if he is not in good health.

2. Main Features

1. Brand-new Signal Wake-up Technology, battery work time up to 90 Days.
2. Pioneering Design with separated adjustable Tone level.
3. Humane Design-Maximum Static Stimulation Period is 5 seconds.
4. 3 training modes: static stimulation/ vibration/ tone. 0-3 Adjustable Intensity Levels for Tone; 0-8 Adjustable Intensity Levels for Vibration; 0-16 Adjustable Intensity Levels for Static Stimulation. If the level set 0, the mode is inhibited.
5. IPX6 Waterproof Receiver Collar and IPX5 Waterproof Transmitter.
6. Maximum remote range up to 600m in the open area without any interference.
7. Train up to 2 dogs with one remote transmitter (separately purchase additional receiver).
8. Rechargeable collar and transmitter.

3. Relevant Description

Transmitter description

An illustration shows the remote transmitter. The device features an LCD Screen, Intensity Up/down Buttons, Vibration Button, Static Stimulation Button, Channel Button, Tone Button, and a Charging port.

Receiver description

An illustration shows the collar receiver with an Indicator light switch and a Charging port.

• LCD Screen: The LCD Screen will display different modes of the collar and the different channels for two collar receivers as well as battery indication. Channel A/B will be displayed on the screen.
• Static Stimulation Button: Pressing the “Static Stimulation” button, the receiver will emit static stimulation. If set level 0, NO stimulation.
• Vibration Button: Pressing the “Vibration” button, the receiver will vibrate. If set level 0, NO vibration.
• Beep Button: Pressing the “Beep” button, the receiver will emit beep sound. If set level 0, NO beep.
• Intensity Up/down Buttons: Selects intensity level of beep, vibration, and static Stimulation.
• Channel Button: Pressing this “A B” button will shift channel between the first and second collar receiver.
• Charging port: Insert charging cable into charging port to charge the Transmitter.
• Turn on/off the Receiver: Turn on/off the receiver by pressing the "Power" button one time.
• Micro USB port: Insert charging cable into Micro USB port to charge the receiver.

4. How to Use It

Note: Please charge before using the product!

1. Charge the remote transmitter

1. Connect the charger cable to the charging port.
2. Plug the charger into a standard outlet.
3. The icon of battery will flash.
4. Charge the transmitter for about two hours for the first charge or until the icon of battery stops flashing.

2. To turn the Transmitter on

1. Press any button to activate the Transmitter. The backlight will turn on.
2. Backlight will stay on for about 5 seconds. If no operation, the backlight turns off.
3. The LCD display will stay on for about 5 seconds. If no operation, the LCD display shuts off.

3. Charge the collar receiver

1. Connect the charger cable to the Micro USB port.
2. Plug the charger into a standard wall outlet.
3. The red light will flash on the receiver (If not or green light, please plug the charger again).
4. Charge the receiver for about two hours for the first charge or until the light indicates charging complete.

4. To turn the Receiver Collar on

Press the power button once; the blue light will flash.

5. To turn the Receiver Collar off

Press the On/Off Button until the blue light is gone; this means the receiver is turned off.

6. Connect transmitter and receiver

Two Dog System

NOTE: If you wish to add another Receiver Collar to the training system, extra Receiver Collars are available where you bought your unit.

1. With the Receiver Collar off your pet, turn on the receiver collar.
2. Press the power button of the receiver continuously for three times, and the red light will always be on.
3. Press the TONE, VIBRA, or Static Stimulation (any of them) on the remote; the blue light on the receiver will flash, indicating pairing is completed.
4. Press the TONE button; the receiver receives the command and makes a sound.
5. If the pairing was not successful, please repeat steps 1-3.
6. To match the second receiver, press the "A B" button and select for the second receiver and follow the same procedure.

7. How to use the Test Light

1. Turn the Receiver Collar on.
2. Hold the Test Light Contacts to the Contact Points.
3. Press the SHOCK Button on the Remote Transmitter.
4. The Test Light will flash. Note: At higher Stimulation Levels, the Test Light will flash brighter.
5. Turn the Receiver Collar off.

Save the Test Light for future testing.

Note: If the Test Light does not flash, recharge the Receiver and re-test.

5. How to Connect transmitter and receiver

1. Turn on the transmitter

2. Turn on the receiver

3. Press the power button once.

4. Press the TONE, VIBRA or Static Stimulation (any of them) on remote; the blue light on receiver will flash, it indicates pairing is completed.

Note:

1. If the pairing were not successful, please repeat the 1-4 steps.
2. To match the second receiver, press the "A B" button and select for the second receiver and follow the same procedure.
3. If you wish to add another Receiver Collar to the training system, extra Receiver Collars are available where you bought your unit.

6. Important Notice

1. The display of the transmitter stays on for approximately 6 seconds after a button press. After 6 seconds with no button press, the blue backlight shuts off first. If there is no button press for another 50 seconds, the display shuts off and the transmitter goes into sleep mode with auto-vibration. Pressing any button with auto-vibration will turn the display back on.
2. The receiver will enter shallow sleep mode if it stops working for 5 seconds, and if without any operation for 50 seconds, it will enter deep sleep mode. Any commands from the transmitter will activate the receiver.
3. Press the "A B" button for selection. Channel A controls the first receiver and Channel B controls the second receiver. Channel A B controls both receivers.
4. The design of the receiver is rainproof. The rubber cover has to be put in the right position to ensure the rainproof effect.
5. Test static stimulation function:
   1. Place the Test bulb to the metal screws (ensure the metal points are attached when testing the stimulation function).
   2. Press the “Static Stimulation” button, and the LED light will flash on.
6. How to find the best Vibration/Stimulation Level: The level of Vibration/Stimulation best suited for your dog depends on your dog's temperament and threshold for Vibration/Stimulation. Always start at the lowest level and work your way up. The appropriate level can be found when the dog responds to the Vibration/Stimulation with a mild reaction, such as a tensing of the neck muscles. The Vibration/Stimulation Level may vary depending on the training situation. When highly distracted, dogs will require a higher level of Vibration/Stimulation.

7. Summary of Frequently Asked Questions

Q: Is the Vibration/Stimulation safe for my pet?

A: While the Vibration/Stimulation is unpleasant, it is harmless to your pet. Electronic training devices require interaction and training from the owner to achieve desired results.

Q: How old does my pet have to be before using the Remote Training Collar?

A: Your pet should be able to recognize basic obedience commands such as “Sit” or “Stay”. Pets should be at least 6 months old before using the Training Collar.

Q: Once my pet is trained and has been obeying my commands, will he have to continue to wear the Receiver Collar?

A: Probably not. You may need to reinforce training with the Receiver Collar from time to time.

Q: Is the Receiver Collar waterproof?

A: It's water resistant/rainproof. Be sure to keep the rubber cover put in the right position and do not make the dog swim in water.

Q: How long can I continuously deliver Vibration/Stimulation to my pet?

A: The maximum amount of time you can press the Stimulation Button and deliver Stimulation to your pet continuously is 5 seconds. And the maximum amount of time you can press the Vibration Button and deliver Vibration to your pet continuously is 10 seconds. After this, Vibration/Stimulation cannot be delivered until you release and press the button again.

Q: How long should I process my training session for my pet?

A: Training sessions should be kept positive and short; it is better for about 10-15 minutes each time.

8. FCC Compliance

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

9. Declaration of Conformity:

Declaration of conformity (see chapter "Declaration of conformity"): Products designated with this symbol fulfill all applicable community provisions of the European Economic Area.

This symbol certifies that the device's electromagnetic interference is below the limit approved by the United States Federal Communications Commission.

Disposal:

Disposing of packaging: Dispose of the packaging according to type:

• Cardboard and carton to waste paper
• Foils in the recycling collection

Disposing of the device: Applicable in the European Union and other European countries with systems for separate collection of recyclable materials.

Old devices must not be disposed of in household waste! If the Modular Remote Trainer can no longer be used, all consumers are required by law to hand over the old devices separate from household waste, for example, at a collection point of their local community/district. This ensures that the old appliances are properly recycled and that negative effects on the environment are avoided. That is why electrical devices are marked with the symbol shown here.

Reference Size for Different Dogs

Reference Weight for Dogs

• Large Dog (Body height above 24 inch, Weight above 88 lbs)
• Medium Dog (Height 16-24 inch, Weight 24.2-66 lbs)
• Small Dog (Height 10-16 inch, Weight 8.8-22 lbs)
• Mini Dog (Height under 10 inch, Weight under 8.8 lbs)

10. Declaration:

The following tips will show you how to get the best performance out of your Dog Training Collar.

1. Make training sessions short and positive (about 10-15 minutes for each session). This will enable the dog to focus on the trainer.
2. Training one dog each time is recommended.
3. During the first initial training sessions, keep the dog in a familiar outdoor environment. Training in a place that the dog is not familiar with may make the dog become distracted.
4. Use a long leash fastened to a non-metallic collar to help the dog to learn. Ensure that the additional collar and leash does not interfere with the Contact Points of the Collar Receiver. Do not use the remote training collar without a long leash unless your dog is fully trained.
5. More success will occur by teaching the dog a command first before trying to reinforce the command with the Remote Transmitter.
6. For basic obedience training, vibration is more useful.
7. Issue one obedience command each time; this will reduce confusion and allow the dog to remain focused. Do not use the training system for commands that the dog has not learned.
8. During training, look for all the positive changes in the dog's behavior and remember to encourage it promptly with ample praise and reward.
9. Avoid over-correcting your dog. Use as little remote correction as possible during the training process.
10. When the dog has become apparently perplexed, shift the focus of the training by drawing the dog's attention to a command they have been familiar with. Example: Tell the dog to sit and give abundant praise and encouragement on successful completion of the sit command.
11. Do not use the training system to correct or eliminate aggressive or biting behavior. When the dog is showing signs of aggressive behavior, contact a professional dog trainer in your local area immediately.
12. Please keep in mind that training sessions should be kept short. Stop training and play with the dog when the dog has made progress.

Service center and distribution

Reedog, sro

Sedmidomky 459/8 101

00 Prague 10

Phone: +1 646 980 4569

Email: info@electric-collars.eu

The device has been approved for use in EU countries and is therefore provided with the CE mark. All necessary documentation is available on the website: www.electric-collars.com. Changes to technical parameters, properties, and printing errors reserved.