Onn. 5W Qi Dash Mount Wireless Car Charger

What is in the box?

• 1. 5W Qi Wireless Car Charger
• 2. 3-ft micro-USB charging cable
• 3. Car Dash Mount
• 4. User Manual

Get to know your 5W Qi wireless car charger

Wireless Charging Pad: The main unit for wireless charging.

Input: Micro-USB, 5VDC/2A

Output: 5W

Dimension: 100mm*63mm*20.5mm

Compatibility:

• Qi-enabled smartphones charge up to 5W
• Any Qi-compatible smartphones

Key Parts:

• Clamping arm L [left clamp]
• Clamping arm R [right clamp]
• Pivot Ring [adjustment ring]
• Telescopic Arm [adjustable arm]
• Pivot [joint for arm]
• LED status indicator [charging status light]
• Release button [button to open clamps]
• Suction cup [for mounting]
• Micro-USB Port [for power input]

How to charge your devices

Assemble the dash mount with charger:

1. Untighten the pivot ring at the back of the charger.
2. Rotate the pivot ring to loosen it.
3. Insert the dash mount into the pivot.
4. Tighten the pivot ring with the dash mount to secure it.
5. Adjust the telescopic arm to the desired position.

Connect Micro-USB cable with Charger:

1. Insert the Micro-USB connector of the charging cable into the Micro-USB port of the charger.
2. Connect the USB connector to a car charger (car charger sold separately).
3. Connect the car charger to the automotive auxiliary power outlet.
4. Place the telescopic arm to the dashboard using the suction cup.

Place and charge your phone:

1. Place your smartphone on the charger.
2. Close the clamping arms to secure the phone. The LED indicator will show charging status.
3. To release your phone, push the release button on the right side of the charger.

Important Information

Caution

• Avoid dropping the device.
• Do not disassemble the device.
• Ensure no metal objects are between the device and the wireless charging car charger.
• Thick protective cases (over 5mm) or cases with magnets or metallic material may prevent proper charging.
• Keep the wireless charging car charger away from liquids or moisture.
• Do not expose the device to temperatures exceeding 45°C (113°F) or place it in fire or excessively hot environments.
• Clean the product only with a dry cloth or brush.
• Do not use the product if visible defects are observed.

Warning

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

FCC Statements

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Technical Specifications & Notes

Part Number: 250-220100-C52R

Supplier P/N: *

DWG NO: RDN1910289-034

Model: WIABLK100008882

Dimensions and Specifications: These drawings and specifications are the property of Luxshare-ICT and shall not be reproduced, copied, or used in any manner without the prior written consent of Luxshare-ICT.

Notes:

• 1. Appearance inspection: According to the "Packaging Parts Inspection Specification".
• 2. Dimensions marked with "" are key control dimensions; tolerances not specified refer to the 3D drawing.
• 3. Material: 80g art paper.
• 4. Content: Refer to the corresponding Artwork document.
• 5. This product's materials and processes must comply with the environmental management substance requirements of document "QW-Q-043" - ROHS2.0.

Revision Information:

REV: A, DESCRIPTION: NEW DRAWING, DESIGN: XUBIAO LIU, APPROVAL: JACK, DATE: 2019.12.29

Additional Notes:

The barcode requires scannability for identification. [条码需可以扫描识别]

Document issued by Bosuo Technology on 2020.02.21. [博硕科技 2020.02.21 资料发行章]

Support: Need help? Call 1-888-516-2630 daily from 7 a.m. - 9 p.m. CST.