D-Link M60 AX6000 Wi-Fi 6 Smart Mesh Router

What's in the Box

• M60 Router Unit (x1)
• Power Adapter (x1)
• Ethernet Cable (x1)
• Quick Installation Guide (x1)

Installation Instructions

1. Connect the M60 to your modem using an Ethernet cable.
2. Wait for the M60's LED indicator to start pulsing orange. This process should take less than 3 minutes.

Option 1: Using the AQUILA PRO AI App

1. Download the AQUILA PRO AI app from the App Store or Google Play.
2. Follow the in-app instructions to set up your new device.

Option 2: Router Setup

1. Connect the M60 to your computer via an Ethernet cable.
2. Access the setup page by navigating to `http://xxxx.devicesetup.net/` in your web browser. (XXXX represents the last 4 characters of the MAC address).
3. Enter the Device Password: XXXXXX.
4. Configure your Wi-Fi Name (SSID) as M60-XXXX and set your Wi-Fi password as XXXXXXXXXX.

Option 3: Range Extender Setup

1. Connect the M60 to your computer via an Ethernet cable.
2. Access the setup page by navigating to `http://xxxx.devicesetup.net/` in your web browser. (XXXX represents the last 4 characters of the MAC address).
3. Enter the Device Password: XXXXXX.
4. The M60 will automatically pair with your existing wireless router, sharing the same Wi-Fi Name and password.

Setting your M60 up as a Range Extender

To pair your devices with M60, follow the steps below:

1. Plug in to power on M60 and place it near your wireless router. Wait for M60's LED indicator to start pulsing orange.
2. Press the WPS button on the router for 3 seconds. Refer to your router's user manual for router behavior.
3. Press the WPS button on your M60 for 3 seconds. The LED indicator should start pulsing white.
4. When M60's LED indicator turns solid white (may take up to 3 minutes), this indicates M60 is connected to your wireless router.

You have now completed the setup! You can move your M60 to any location you want for wireless coverage. By default, your M60 shares the same Wi-Fi Name and password of your wireless router.

NOTE: WPS may be disabled on certain routers. If the LED indicator does not blink after pressing the WPS button, try again and press it a little longer. If that still does not work, use AQUILA PRO AI App for setup instead.

M60 Overview

LED Status Indicators:

• Solid white: Connected to the Internet and in operation.
• Pulsing white: WPS in operation.
• Pulsing orange: Ready for connection or is not set up.
• Interleaving white/orange: Firmware updating.
• Pulsing red: Booting up or resetting to factory default.
• Solid red: Powering on.

Router Modes:

• Solid white: Connected to the Internet and in operation.
• Pulsing white: WPS in operation.
• Pulsing orange: Ready for connection or is not set up.
• Interleaving white/orange: Firmware updating.
• Pulsing red: Booting up or resetting to factory default.
• Solid red: Powering on.

Extender Modes:

• Solid white: Connected to an uplink router and with good wireless signal.
• Pulsing white: Connected to an uplink router but with weak wireless signal.
• Pulsing orange: Cannot connect to an uplink router or is not set up.
• Interleaving white/orange: Firmware updating.
• Pulsing red: Booting up or resetting to factory default.
• Solid red: Powering on.

Device Ports and Buttons:

• 1: LED On/Off button
• 2: Internet port
• 3: Ethernet port
• 4: RESET button
• 5: Power connector (12V/2.5A)
• 6: Power button
• 7: WPS button
• 8: LED status indicators

FAQ

• Why can't I access the Internet? Please reset your wireless router, and if it still does not work, please contact your internet service provider.
• What do I do if I forgot my router's login password? Please reset your wireless router to default settings and set it up again.
• How do I restore the router to its factory default settings? With the router powered on, press the reset button with a paperclip for 1 second and then release it. The M60 will now be at its factory default settings.
• How to Build a Mesh Network with Ethernet Backhaul? To create a wired Ethernet backhaul connection, simply connect an Ethernet cable from the LAN port on your Mesh Wi-Fi router to the LAN port on your Mesh Wi-Fi node. The Status LED will turn solid white once it has finished pairing with your Mesh Wi-Fi network in a few minutes.

FCC Warning

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) The device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

GPL Code Statement

GPL Source Code Support: https://tsd.dlink.com.tw/GPL

Technical Support

Having trouble installing your new product? D-Link's website contains the latest user documentation and software updates for D-Link products. Customers can contact D-Link Technical Support through our website by choosing the relevant region.

Contact Us

www.dlink.com/en/contact-us

United States

Website: http://support.dlink.com

Canada

Website: http://support.dlink.ca/M60