SCS Sentinel SimplyOpen 1+ Motorization for Swing Gates

Introduction

This document provides instructions for the installation and use of the SCS Sentinel SimplyOpen 1+ actuator automation kit for swing gates. It is designed for residential use and requires qualified personnel for installation.

Safety Instructions

WARNING: Important safety instructions must be followed to prevent serious injury. Incorrect installation can cause harm. Keep these instructions for future reference. Ensure the end-user is trained on safe operation.

General Information: SCS Sentinel automations comply with European safety standards (EN 60335-2-103). Using the product outside specified conditions or with non-recommended accessories can compromise safety.

Before Installation:

• This product is exclusively for automating swing gates in residential settings.
• Installation requires qualified personnel with mechanical and electrical skills.
• Verify the gate is in good mechanical condition, balanced, and operates correctly.
• Ensure the operating temperature range is suitable for the installation location.
• ATTENTION: Automation cannot be used with a gate incorporating a pedestrian door.

Electrical Installation:

• DANGER: Power supply installation must comply with local regulations (e.g., NF C 15-100 in France) and be performed by qualified personnel.
• The mains power supply must be protected against surges by an appropriate circuit breaker and a residual current device. A device for complete disconnection of all power supply poles is required.
• If the power cable is damaged, it must be replaced by the manufacturer, their after-sales service, or similarly qualified personnel to avoid hazards.

Automation Installation

PERIL: Disconnect the automation from its power source during installation.

WARNINGS:

• Ensure no children are present during installation.
• Avoid or signal risk zones around the gate and fixed parts.
• Verify that the gate's opening movement does not cause crushing between the moving part and surrounding fixed parts.
• Manual unlocking can cause uncontrolled movement due to mechanical faults or imbalance.
• If a fixed control device (keypad, selector) is used, it must be installed 1.5m from the ground, away from moving parts, but near the gate.
• Depending on installation environment and regulations (EN 12453, EN 13241-1), additional accessories like photocells and flashing lights may be necessary.
• Automatic closing or remote opening without direct gate visibility requires photocells.
• If the gate is on a public road or uses automatic closing, a flashing light may be mandatory. The installer is responsible for compliance.
• After installation, verify correct mechanism adjustment and proper functioning of safety and manual unlocking devices.
• Permanently affix the manual unlocking device label to the mechanism.

Using the Automation

ATTENTION: This appliance may be used by children aged 8 and above, and persons with reduced physical, sensory, or mental capabilities, if supervised and instructed on safe use, understanding the risks. Children must not play with the appliance. Cleaning and maintenance should not be done by unsupervised children. Keep controls out of reach of children.

WARNINGS: Supervise the gate during operation and keep people at a distance until it is fully open or closed. Do not intentionally impede the gate's movement.

Maintenance and Cleaning

PERIL: Disconnect the automation from its power source before cleaning or maintenance.

• Periodically check the installation for incorrect balancing, wear on cables, springs, or mounting. Do not use if repairs or adjustments are needed.
• Use only original spare parts for replacement or repair.

Remote Controls

PERIL: Do not ingest battery: risk of chemical burns. Keep batteries out of reach of children. If the battery compartment does not close securely, do not use the product. Seek medical attention if a battery is swallowed. Use a soft cloth for cleaning. Do not let children play with the product or packaging. Use identical batteries for replacement. Remove batteries if the product will not be used for a long period. Do not expose batteries to excessive heat or dispose of them in fire.

Potential Risks

There are 4 potential risks identified:

• Risk 1: Impacts and Crushing: Prevention: Obstacle detection via motor, use of photocells.
• Risk 2: Hand Crushing: Prevention: Maintain a minimum 10 cm gap between the gate leaf and the post/wall. Notch the post angle without weakening it.
• Risk 3: Trapping and Crushing: Prevention: Obstacle detection by the motor. Maintain a minimum 50 cm distance between the motor arm and the wall (or other fixed part).
• Risk 4: Foot Crushing: Prevention: Maintain a minimum 12 cm or maximum 5 mm gap between the base of the gate leaves and the ground.

Specifications

Kit Contents:

• 2 x MPD0203 Motorizations
• 1 x Control Box
• 2 x Remote Controls
• Unlock Sticker
• Manual
• Fasteners
• Mounting Brackets

Dimensions:

Diagrams showing the dimensions of the motor unit and its components are provided.

Wiring / Installation

C1- Automation Installation:

• Components: Flashing light (optional), control box, photocells (optional), gate motorization, 2-channel remote control.
• Requirements: Central stop in closing and side physical stops in opening are essential (not supplied).

C2- Dimension Table:

Scrupulously observe the indicated measurements for correct installation. Adjust the gate structure if necessary. Ensure the gate operates freely: hinges are correctly positioned and lubricated, no obstacles in the movement path, no friction between leaves or with the ground.

Opening Inward - Installation with Closed Gates: A table and diagram illustrate ideal mounting angles based on gate width (A) and height (B).

Opening Outward - Installation with Open Gate (max 90°): A flashing light is mandatory for outward opening. A metal part may be needed to offset the motors; installation dimensions must be respected. A table and diagram illustrate ideal mounting angles.

C3- Emergency Release:

In case of power failure or programming, the motors can be manually unlocked using the hexagonal key. Rotate 180 degrees counter-clockwise to unlock. Rotate clockwise to lock. Apply the manual release label permanently.

C4- Arm Fixing:

Unlock the arm (C3) and fully extend the ram tube, inserting it 3 cm to ensure the gate is locked when closed. Fix the first bracket to the post, position the automation, and insert the screw and nut. Assemble the second bracket to the other side of the automation and attach to the closed gate. Ensure arms are mounted horizontally. Cover the automation when welding the bracket to prevent damage from sparks.

C5- Wiring Diagram

Figure 1 shows the wiring diagram for the control board (P100 PCB1). It details connections for the transformer, fuses, antenna, flashing light, photocells, key selector, button, lock, and motors (M1, M2). Mandatory wiring gauge is ≥ 0.5 mm², recommended is 1 mm².

C6- Installation

Electronic Control Box:

• Determine the placement of the control box, preferably near the gate and protected.
• Verify cable length before determining placement.
• Preparation: Remove cover screws, punch holes for cable entry, mount the box, connect wires as per diagrams, pass cables through the bottom, seal holes, and close the box.

Motor Wire Connection:

Connect motor wires (white/yellow) to the terminal block. Ensure wires are stripped to 5 mm and not too taut. For outward opening gates, connect yellow to Mo1+/Mo2+ and white to Mo1-/Mo2-.

Motor Connections

Diagrams show the connection of Motor M1 (initial opening) and Motor M2 (subsequent opening) to the control board. Ensure correct polarity.

Electric Lock (Optional):

Connect the 2 wires of the electric lock (24V) to the Lo+ and Lo- terminals on the control board.

230V Power Connection:

Connect the 230V power supply to the appropriate terminals on the control box.

Photocells (Optional - AAM0036)

Photocells are safety devices composed of an emitter and receiver. They activate when the beam is interrupted. If an obstacle is detected, the gate stops and opens slightly. Wiring requires 0.5 mm² cable.

Phases:

• Phase 1: Mounting the photocell unit.
• Phase 2: Wiring the photocell units.
• Phase 3: Alignment check (diagrams show correct and incorrect alignment).
• Phase 4: Wiring to the control board.
• Phase 5: Final installation.

Flashing Light (Optional - AAM0111)

Remove packaging before connection. The flashing light operates on 24V DC. The antenna can be extended using RG58 coaxial cable. Connect the antenna to the ANT terminal and the braided copper mesh to the GND terminal.

D- ADJUSTMENT / USE

D1- One or Two Leaf Adjustment (Dip Switch 1):

SW1: D/S set. ON = 2-leaf operation, OFF = 1-leaf operation (connected to MOT 1).

D2- Dip Switches 2 and 3:

Switches 2 and 3 are not used.

D3- Automatic Closing Adjustment (Dip Switch 4):

ON: Automatic closing after 30 seconds. Pressing the gate buttons simultaneously cancels automatic mode. Repeat to activate automatic mode. Note: photocells are required for automatic closing.

OFF: No automatic closing (automatic mode can still be activated by remote control).

D4- Photocell Adjustment (Dip Switch 5):

ON: Photocells are active. Crossing photocells during closing stops the gate for 2 seconds. Crossing open photocells resets the pause time.

OFF: Photocell function is disabled.

D5- Opening and Closing Phase Shift (Dip Switch 6):

ON: 8-second phase shift for opening and closing.

OFF: 5-second phase shift for opening and closing.

D6- Slowdown Speed:

Operating speeds are not adjustable.

D7- LED Indicators

• LED1 (RF): Flashes when a signal is received.
• LED2 (Learning System): Flashes twice per second in normal mode, once per second in programming mode. Solid indicates learning needs to be performed or redone.
• LED3 (Photocells): Lights up when photocells are misaligned or an obstacle is present.
• LED4 (Start): Lights up when the remote control, key selector, or button is activated.

D8- Remote Control Learning Process

Add Remotes: Press "RF-Learn" until LED1 lights up. Press a button on the remote. LED1 flashes twice and stays on for 10 seconds. Remote saved.

Delete Remotes: Press and hold the RF button until LED1 turns off.

D9- Dual Leaf System Learning Process

1. Ensure Switch 1 is ON.
2. Unlock motors, position both leaves mid-travel, then relock.
3. On the control board, press and hold SYS-learn until LED2 flashes once per second.
4. Press the left button on the remote.
5. The system will learn the sequence: MOT2 closes fully, MOT1 closes fully, MOT2 opens fully, MOT1 opens fully, MOT2 closes fully, MOT1 closes fully. If a leaf opens unexpectedly, interrupt the process by pressing the remote button again, invert motor polarity, and restart.

After learning, the gate can be operated with the remote for full opening or pedestrian opening.

D10- Single Leaf System Learning Process

1. Ensure Switch 1 is OFF.
2. Connect the motor to MOT1 output.
3. Unlock the motor, position the leaf mid-travel, then relock.
4. On the control board, press and hold SYS-learn until LED2 flashes once per second.
5. Press the right button on the remote.
6. The system will learn the sequence: Leaf closes fully, Leaf opens fully, Leaf closes fully. If the leaf opens unexpectedly, interrupt the process, invert motor polarity, and restart.

D11- Obstacle Detection

If an obstacle is detected during opening, the gate stops. If detected during closing, the gate stops, opens slightly, and recloses. When reaching the closing limit, the gate reopens to clear the obstacle.

E- TECHNICAL SPECIFICATIONS

Motor:

• Type: 24V DC ram actuator with manual release
• Stroke Length: 435 mm
• Power Supply: 24V DC
• Max Weight per Leaf: 150 kg
• Max Width per Leaf: 2 m
• Operating Temperature: -20°C to +50°C
• Dimensions: 710 mm x 98 mm x 192 mm
• Sound Pressure Level: ≤ 70 dB(A)

Remote Controls:

• Channels: 2
• Frequency: 433.92 MHz, power < 10mW
• Power Supply: 1 x CR2032 lithium battery (supplied)
• Security: Variable code

Photocells (Optional - AAM0036)

• Detection Method: Infrared
• Range: 10 m
• Input Voltage: 12-24V AC/DC
• Response Time: < 100 ms
• Indicators: RX LED red (beam interrupted), TX LED red (power).
• Dimensions: 63 x 63 x 30 mm
• Output: Relay

Flashing Light (Optional - AAM0111)

• Integrated Antenna: Yes (coaxial cable not supplied)
• Bulb: LED E14 24V 1W (supplied)
• Power Cable: 2 x 1 mm² (not supplied)
• Connection: No Polarity (electronic board)
• Fasteners: Supplied
• Do not power with 230V
• Operating Temperature: -20°C to +50°C
• Dimensions: 74 x 167 x 59 mm

F- MAINTENANCE

F1- Motor:

Perform maintenance every 6 months, or more frequently with heavy use.

• Interrupt Power:
• Clean and lubricate screws, anchors, and hinges.
• Check that fixing points are securely tightened.
• Verify correct cable connections.
• Connect Power:
• Check power supply adjustments.
• Verify manual release function.
• Verify correct operation of photocells and other safety devices.

F2- Remote Controls:

Diagrams show remote control battery replacement (CR2032).

G- TECHNICAL ASSISTANCE

G1- Troubleshooting:

A table lists common problems and their solutions, including issues with reserve batteries, gate movement, transmission distance, flashing light, sudden stops, single-direction movement, and remote control connectivity.

G2- Expert Advice:

After-sales service technicians are available at 0039 01119620971. Contact customer service for assistance during installation or shortly after.

G3- Online Assistance:

For personalized answers, use the online chat at www.scs-sentinel.com.

H- WARRANTY

SCS Sentinel offers a warranty exceeding the legal duration. Proof of purchase must be kept for the warranty to be valid. The warranty does not cover damages from incorrect installation, improper use, use of non-approved parts, lack of maintenance, impacts, or weather events.

I- WARNINGS

Do not dispose of batteries and used appliances with household waste. Use designated collection points for proper disposal.

J- EU DECLARATION OF CONFORMITY

SCS Sentinel declares that this product complies with essential requirements and provisions of Directive 2014/53/UE and Directive 2006/42/CE. The declaration of conformity is available at www.scs-sentinel.com/downloads.