Package Contents
- Home Studio/Home Studio Lite Booster & Booster Antenna
- 2-30 ft. Cables
- Outside Antenna & L-Bracket Antenna Mount
- Power Supply
Installation Steps
STEP 1: Attach Booster Antenna to Booster & Place in Desired Location
Attach the Booster Antenna to Home Studio/Home Studio Lite Booster and place in room where stronger cell signal is needed.
[Diagram: Booster Antenna connected to Home Studio/Home Studio Lite booster.]
STEP 2: Mount & Point Outside Antenna Toward Nearest Cell Tower
Pole mounting is preferred because it will be easier to adjust to the direction of the cell tower. Use the U-Bolts to attach the Antenna to a pole or exhaust pipe on roof.
[Diagram: Outside Antenna mounted on a pole using an L-bracket and U-bolts. Drip holes are visible on the antenna.]
Side Mounting
Side mounting is an option if you can still obtain strong signal. Note: Drip holes should be pointed down towards ground.
[Diagram: Side mounting of outside antenna with drip holes pointing downwards.]
STEP 3: Route & Connect Outside Antenna To Booster
Connect the white RG-6 Cable to Outside Antenna and route and connect cable to Home Studio/Home Studio Lite Booster. All connections should be finger tightened only.
[Diagram: RG-6 cable connecting the outside antenna to the booster.]
STEP 4: Power Up The Booster & Optimize The System
Plug the Power Supply into wall outlet then connect into end of Booster. NOTE: weBoost strongly recommends using a power strip with surge protection.
[Diagram: Booster with power supply connected, showing status lights at the top.]
Optimizing the System
After powering up your system, check to see how your talk, text, and data rates have improved. If more is desired, you can optimize your system.
Rotate the Outside Antenna in 1/8 turn increments, after each turn, unplug and reconnect the Booster to power while observing the signal level on your cell phone from the Inside Antenna's projected area. When you have determined a direction that gives you the strongest signal, secure the Outside Antenna in place.
The following table shows how boosted cell signal coverage relates to the strength of the outside signal:
| If the cell signal outside your home is: | Strong | Good | Weak | None |
|---|---|---|---|---|
| Your boosted cell signal will cover: | Large Room | Medium Room | Small Room | None |
[Diagram: Cell phone receiving a signal from the inside antenna, illustrating the optimization process.]
Status Light Patterns
GREEN
This indicates that your Home Studio or Home Studio Lite Booster is functioning properly and there are no issues with installation.
SOLID RED
Band has shutoff. This is due to a feedback loop condition called oscillation. This is a built-in safety feature that causes a band to shut off to prevent harmful interference with a nearby cell tower. Refer to Troubleshooting section.
BLINKING GREEN, RED
This indicates that the Booster is operating at a reduced gain to prevent oscillation (feedback). This is a built-in safety feature to prevent harmful interference with a nearby cell tower. If you are already experiencing the desired signal boost, then no further adjustments are necessary. If you are not experiencing the desired boost in coverage then refer to the Troubleshooting section.
BLINKING GREEN, YELLOW
This indicates Band has reduced gain. This indicates that one or more of the Booster bands has reduced power due to overload from a nearby cell tower. This is a built-in safety feature to prevent harmful interference with a nearby cell tower. If you are already experiencing the desired signal boost, then no further adjustments are necessary. If you are not experiencing the desired boost in coverage then refer to the Troubleshooting section.
SOLID YELLOW
Band has shutoff due to overload from a nearby cell tower. Outside Antenna must be adjusted. Refer to Troubleshooting section.
LIGHTS OFF
If the Signal Amplifier's light is off, verify your Power Supply has power.
[Diagrams illustrate the Home Studio Booster Lights and Home Studio Lite Booster Lights, showing indicators for different frequency bands.]
Troubleshooting
FIXING RED LIGHT ISSUES (Solid Red & Blinking Green/Red lights)
- Tighten all cable connections (be sure to handtighten only, do NOT use tools). You may want to undo and redo the connection completely. Unplug and replug in Power Supply.
- Increase the distance (horizontally or vertically) between the Outside and Inside Antennas. Add included cable if needed. Unplug and replug in Power Supply.
FIXING ANY YELLOW LIGHT ISSUES (Solid Yellow & Blinking Green/Yellow lights)
- Outside Antenna must be adjusted. Disconnect and reconnect power between adjustments. Wait at least 10 seconds between adjustments for the lights to reset.
- Pole Mount Option: Rotate the Outside Antenna away from the strongest cellular signal in small increments (1/8 turn) until the light turns green. Unplug and replug in Power Supply.
- Mounting On Side Of Roof Option: Change mount location. Move the Outside Antenna to location of the home/building to see if the lights turn green. Unplug and replug in Power Supply. Then secure in place.
Safety Guidelines
Verify that both the Outside Antenna and the adapter extension cable are connected to the Signal Amplifier before powering up the Signal Amplifier.
Use only the Power Supply provided in this package. Use of an incorrect Power Supply may damage your equipment.
RF Safety Warning: Any antenna used with this device must be located at least 8 inches from all persons.
AWS Warning: The Outside Antenna must be installed no higher than 31 feet 9 inches above ground.
This is a CONSUMER device.
BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider's consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider.
You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from any person.
You MUST cease operating this device immediately if requested by the FCC or licensed wireless service provider.
WARNING: E911 location information may not be provided or may be inaccurate for calls served by using this device.
This device may be operated ONLY in a fixed location for in-building use.
For More Information on Registering Your Signal Booster with Your Wireless Provider:
- T-Mobile/Sprint/MetroPCS: https://www.t-mobile.com/support/coverage/register-a-signal-booster
- Verizon Wireless: http://www.verizonwireless.com/wcms/consumer/register-signal-booster.html
- AT&T: https://securec45.securewebsession.com/attsignalbooster.com/
- U.S. Cellular: http://www.uscellular.com/uscellular/support/fcc-booster-registration.jsp
Antenna Info
The following accessories are certified by the FCC to be used with the Home Studio or Home Studio Lite Cell Signal Boosters.
HOME STUDIO
| BAND 2 | BAND 4 | BAND 5 | BAND 12 | BAND 13 | |
|---|---|---|---|---|---|
| Outside antenna maximum permissible antenna gain (dBi) 50Ω | 6.1 | 5.8 | 4.5 | 4.9 | 4.9 |
HOME STUDIO LITE
| BAND 12 | BAND 13 | |
|---|---|---|
| Outside antenna maximum permissible antenna gain (dBi) 50Ω | 4.9 | 4.9 |
INSIDE ANTENNA INFO
| # | Coax Type | Ln(ft) | Antenna Type | Ω |
|---|---|---|---|---|
| 311236 | NONE | 0 | Omni | 50 |
OUTSIDE ANTENNA INFO
| # | Coax Type | Ln(ft) | Antenna Type | Ω |
|---|---|---|---|---|
| 314475 | RG-6 | 30 | Directional | 75 |
| 314473 | RG-6 | 30 | Panel | 75 |
| 304421 | RG-6 | 30 | Omni | 75 |
Specifications
Home Studio Cell Signal Booster
| Model | 460066 | ||||
| FCC | PWO460066 | ||||
| Connectors | F-Female / SMA Female | ||||
| Antenna Impedence | 75 Ohms / 50 Ohms | ||||
| Frequency | 698-716 MHz, 728-756 MHz, 777-787 MHz, 824-894 MHz, 1850-1995 MHz, 1710-1755/2110-2155 MHz | ||||
| Power output for single cell phone (Uplink) dBm | 700 MHz B12/17: 23.3 | 700 MHz B13: 22.2 | 800 MHz B5: 23.3 | 1700 MHz B4: 22.1 | 1900 MHz B2: 21.8 |
| Power output for single cell phone (Downlink) dBm | 9.4 | 9.6 | 7.0 | 11.8 | 13.8 |
| Noise Figure | 5.0 dB (nominal) | ||||
| Isolation | > 90 dB | ||||
| Power Requirements | 4.2V, 2.5A |
Each Signal Booster is individually tested and factory set to ensure FCC compliance. The Signal Booster cannot be adjusted without factory reprogramming or disabling the hardware. The Signal Booster will amplify, but not alter incoming and outgoing signals in order to increase coverage of authorized frequency bands only. If the Signal Booster is not in use for five minutes, it will reduce gain until a signal is detected. If a detected signal is too high in a frequency band, or if the Signal Booster detects an oscillation, the Signal Booster will automatically turn the power off on that band. For a detected oscillation the Signal Booster will automatically resume normal operation after a minimum of 1 minute. After 5 (five) such automatic restarts, any problematic bands are permanently shut off until the Signal Booster has been manually restarted by momentarily removing power from the Signal Booster. Noise power, gain, and linearity are maintained by the Signal Booster's microprocessor.
This device complies with Part 15 of FCC rules. Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by weBoost could void the authority to operate this equipment.
Home Studio Lite Cell Signal Booster
| Model | 460065 | |
| FCC | PWO460065 | |
| Connectors | F-Female / SMA Female | |
| Antenna Impedence | 75 Ohms / 50 Ohms | |
| Frequency | 698-716 MHz, 728-756 MHz, 777-787 MHz | |
| Power output for single cell phone (Uplink) dBm | 700 MHz B12/17: 24.3 | 700 MHz B13: 23.0 |
| Power output for single cell phone (Downlink) dBm | 11.7 | 12.9 |
| Noise Figure | 5.0 dB (nominal) | |
| Isolation | > 90 dB | |
| Power Requirements | 4.2V, 1.2A |
Each Signal Booster is individually tested and factory set to ensure FCC compliance. The Signal Booster cannot be adjusted without factory reprogramming or disabling the hardware. The Signal Booster will amplify, but not alter incoming and outgoing signals in order to increase coverage of authorized frequency bands only. If the Signal Booster is not in use for five minutes, it will reduce gain until a signal is detected. If a detected signal is too high in a frequency band, or if the Signal Booster detects an oscillation, the Signal Booster will automatically turn the power off on that band. For a detected oscillation the Signal Booster will automatically resume normal operation after a minimum of 1 minute. After 5 (five) such automatic restarts, any problematic bands are permanently shut off until the Signal Booster has been manually restarted by momentarily removing power from the Signal Booster. Noise power, gain, and linearity are maintained by the Signal Booster's microprocessor.
This device complies with Part 15 of FCC rules. Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by weBoost could void the authority to operate this equipment.
Notes & Contact Information
For notes, please use the blank lines provided.
Contact Information:
- ? 866.294.1660
- ? www.weboost.com
- ✉️ support@weboost.com
2 YEAR WARRANTY
weBoost Signal Boosters are warranted for two (2) years against defects in workmanship and/or materials. Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase.
Signal Boosters may also be returned directly to the manufacturer at the consumer's expense, with a dated proof of purchase and a Returned Material Authorization (RMA) number supplied by weBoost. weBoost shall, at its option, either repair or replace the product.
This warranty does not apply to any Signal Boosters determined by weBoost to have been subjected to misuse, abuse, neglect, or mishandling that alters or damages physical or electronic properties.
Replacement products may include refurbished weBoost products that have been recertified to conform with product specifications.
RMA numbers may be obtained by contacting Customer Support.
DISCLAIMER
The information provided by weBoost is believed to be complete and accurate. However, no responsibility is assumed by weBoost for any business or personal losses arising from its use, or for any infringements of patents or other rights of third parties that may result from its use.
Company Information
A WILSON ELECTRONICS BRAND
3301 East Deseret Drive, St. George, UT
- ? 866.294.1660
- ? www.weboost.com
- ✉️ support@weboost.com
Copyright © 2020 weBoost. All rights reserved. weBoost products covered by U.S. patent(s) and pending application(s)
For patents go to: weboost.com/us/patents
NOT AFFILIATED WITH WILSON ANTENNA
Document ID: GDE000364_001_11.30.20
