Mivardi Carp Scout XL / Li / LA

Introduction

This instruction manual is intended for the Mivardi Carp Scout XL, Li, and LA models. It provides essential information for the correct operation and utilization of all boat functions. Please read this manual carefully before using the product to ensure proper setup and performance. Incorrect settings may lead to malfunctions.

Boat Functions and Specifications

• Fully digital duplex remote control at 2.4 GHz.
• Remote controller with a built-in antenna and LCD display showing the boat's status and functions.
• Integrated digital compass for automatic sailing in the selected direction.
• GPS navigation system with the ability to save up to 31 positions for automatic navigation.
• Built-in echo sounder displaying bottom relief, water temperature, and fish presence on the controller's display.
• Automatic return to the starting point in case of remote control failure or loss of signal.
• Automatic check of key functions, displaying icons for any detected problems (compass, GPS, echo sounder).
• Possibility to update boat and controller firmware via a service center.

Cruise Control Modes

• MANU (manual sailing): Control navigation direction manually using the joystick.
• AUTO (automatic sailing): The electronic compass maintains the set direction. The joystick can be used for manual correction.
• GPS (sailing with GPS navigation): The boat automatically sails to pre-set target points using GPS navigation and the electronic compass.

Fish Finder (Echolot)

Main Functions:

• Measures water temperature.
• Measures water depth up to a maximum of 30 meters.
• Automatically switches between 4 depth ranges: 2-5 m, 5-15 m, 15-20 m, and 20-30 m.
• Displays icons for fish in three sizes: large, medium, and small.
• Fish detection sensitivity levels: C1 / C2 / C3 (from lowest to highest sensitivity).
• Displays bottom profile and hardness.

Notice: The echo sounder functions correctly only in water. It provides accurate depth measurements in water deeper than 2 meters.

GPS Satellite Navigation

GPS Functions:

• Set and save up to 31 GPS points (1 starting 'HOME' point and 30 destination points).
• The boat displays the distance to the 'HOME' point and the selected destination point.
• The boat can automatically sail to selected destination points using GPS navigation.
• Automatic return to the starting point if the remote control connection is lost or fails (requires the 'HOME' point to be stored).
• The boat's front and rear lights flash, and the remote control emits an audible signal when the boat reaches its destination.

Using GPS Navigation:

• After switching on the boat, wait approximately 3 minutes for the GPS system to acquire satellite signals for accurate positioning. At least five GPS satellites are required for correct GPS navigation.
• Press the GPS button to enter the GPS navigation menu, which offers 31 positions (1 'HOME' and 30 numbered destination points). Current GPS coordinates are displayed.
• Use the +/- buttons to select a memory position; the selected position flashes.
• Press and hold the SET button for 3 seconds to save the current boat position to the selected memory position. The icon for the saved position will be highlighted.
• To clear a memory position, select it using +/- buttons and press and hold SET for 3 seconds. The highlight will be removed.
• To navigate to a saved position, select it with +/- buttons and press GO to start automatic navigation. Press GO again to return to the home screen.
• Exit the GPS menu anytime by pressing the ESC button.

Charging

• The charger has LED indicators: red for charging, green for fully charged.
• Boat Battery Charging: Remove batteries from the boat. Connect the supplied splitter to both batteries and the charger, then connect to the power supply. Important: Always charge with both batteries connected; never charge only one.
• Remote Controller Charging: The RC battery is internal and maintenance-free. Connect the charger's USB cable to the RC's USB port and then to a power source. Charge status is shown on the RC display.

Safety Precautions and Warnings

• Do not use the boat during thunderstorms as the antenna is a good conductor of electromagnetic waves and electrostatic discharges.
• Avoid using the remote control in areas with explosive materials.
• The electronic compass is sensitive to external influences. Avoid areas near high-voltage lines, strong magnetic fields, or mining operations.
• Ensure bait hopper door magnets are clean. Dirt can affect the hopper switch function. Clean magnets and metal plates on doors if necessary.
• NEVER disassemble the boat or remote control yourself. Contact your dealer or authorized service center for repairs. Opening the casing voids the warranty.
• The seller notes that the warranty does not cover normal wear and tear. Battery capacity loss due to normal use is not covered by the warranty period.

Technical Specifications

Package Contents

Remote Controller Details

The all-in-one remote controller is designed exclusively for the Carp Scout boats and features a large LCD display for boat status and sailing information. Real-time two-way data transfer enhances user experience.

RC Controls:

1. Main switch / confirmation: Press for 3 seconds to turn the RC on/off. Confirms menu selections.
2. Menu navigation buttons: Navigate through menus.
3. Menu navigation buttons: Navigate through menus.
4. LCD display backlight: Press to toggle backlight on/off. Hold to adjust intensity.
5. Audible warning signals: Activated for low batteries, open bait hopper, released rig hooks, reached GPS destination, or signal loss.
6. GPS: Switches between the main screen and the GPS menu.
7. AUTO mode: Activates automatic sailing. The boat maintains its current direction, but the joystick allows for manual adjustments.
8. Boat lights: Turns boat lights on/off.
9. Rig releasing button: Opens the left rig holder, then the right. Confirmed by audible signal and flashing lights. Pressing a third time resets the display. Rig holders return to starting position automatically after releasing the rig.
10. Bait hopper button: Opens the left bait hopper, then the right. Confirmed by audible signal and flashing lights. Pressing a third time resets the display. Hopper doors must be closed manually.
11. SET: Saves the current boat position to a selected GPS memory position or deletes a saved position.
12. ESC: Exits the GPS menu.
13. + / - buttons: Select memory positions in the GPS menu.
14. + / - buttons: Select memory positions in the GPS menu.
15. GO: Starts automatic GPS navigation to the selected destination point. Press again to interrupt navigation and return to manual control.

Monitoring Key Functions and Fault Reporting

The boat monitors key functions. If a fault is detected, a corresponding symbol appears on the display. Contact your dealer with the error symbol information.

Error Symbols:

• RC compass
• Boat compass
• Fish finder
• GPS module