SSV Works RZ4-2ARC Polaris RZR XP Turbo S 2-Speaker Kit

Warranty Information

All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. All Kicker Speakers are covered by a limited 1 year warranty against defects in material or workmanship. All Kicker Amplifiers are covered by a limited 2 year warranty against defects in material or workmanship. Labor for replacement of defective components is not covered. Contact SSV Works for further warranty information.

Safety First

⚠️ Please read and understand these instructions completely before installation to avoid possible injury, or damage to the accessory or vehicle.

Tools Needed for Installation

• T30 & T40 Torx Socket
• 10mm and 5.5mm Socket & Rachet or Wrench
• 4mm & 5mm Allen Wrench
• #2 & #3 Phillips Screwdriver
• Drill with 13/64", 1/8", 1/4" & 1/2" Drill bits
• Wire Crimpers
• Wire Strippers
• Panel removal tool
• Scribe or Marker
• Utility Knife

Parts List

1. Amp Power Wire x2: Two red wires with ring terminals on one end and a connector on the other.
2. B-H1149 Front Speaker Wire: A wiring harness with a multi-pin connector at one end and two speaker connectors at the other.
3. B-H1151 Rear Speaker Expansion: A wiring harness with a multi-pin connector and a single connector.
4. Amp Tray with pre-loaded Kicker Amplifiers: A black metal tray holding two Kicker amplifiers.
5. Amp Tray Base Bracket: A black metal bracket with mounting holes.
6. M6 x 1.0 Screws and Washers x2: Two bolts and two washers.
7. Self-Tapping Screw and Washer x1: One self-tapping screw and one washer.
8. Zip Ties: Several black plastic zip ties for cable management.
9. Fuse Holder with 40A Fuse x2: Two black fuse holders, each containing a 40A fuse.
10. Battery Terminal Cable x2: Two cables, one red (positive) and one black (negative), with ring terminals.

Panels and Dash Disassembly

1. A. Remove driver seat: Release the handle behind each seat, push forward slightly while lifting up.
2. B. Disconnect battery: Disconnect the negative battery cable from the battery.
3. C. Remove console components: Remove all center console push pins and T-30 Torx screws. For 4-seat models, disconnect the harness attached to the 12v accessory socket.
4. D. Remove hood: Turn locking pins and lift up.
5. E. Remove dash: Unscrew the four T40 torx screws (driver side shown). Extract the two push pins from the dash. From inside the machine, pull the dash towards you to unclip. Once unclipped, remove the dash.

Running Wiring and Cables

1. F. Prepare firewall: Unwrap tape and pull the rubber wire grommet out of the firewall.
2. G. Route wiring: Starting from under the hood compartment, feed the connector of the power wire and B-H1151 rear harness female connector through the grommet into the dash cavity. Pull about 18 inches of the amp power wire and B-H1151 into the dash cavity (G1). Route the additional length of the power/ground wire (ring terminal end) and B-H1151 down the exterior of the firewall along the factory wiring (G2). Pull the power/ground wire through to the center of the vehicle to the battery compartment. DO NOT CONNECT TO THE BATTERY (G3). B-H1151 will be used later for cage mount speakers.

Amp Tray Installation

1. A. Remove lower bolts: Remove the two 10mm bolts circled in pink.
2. B. Install base bracket: Place the amp tray base bracket at the location of the two removed factory 10mm bolts. Re-fasten the bolts through both the amp tray base bracket and factory plate to secure to the chassis.
3. C. Remove upper bolts: Remove the two 10mm bolts circled in pink.
4. D. Mount amp tray: Place the amp tray into the mounting location by aligning the amp plate screw holes to the factory holes on the chassis.
5. E. Secure amp tray: Secure the amp tray using the two 10mm factory bolts at the top, and two T-30 torx bolts at the bottom mounting locations.
6. F. Mark pilot hole: Using a scribe or punch, mark the location of the needed pilot hole on the passenger side of the tray.
7. G. Drill and secure: With the correct location marked, uninstall the amp tray and use a 13/64" drill bit to drill your pilot hole. Reinstall the amp tray and use the self-tapping screw in the drilled hole location.
8. H. Connect amplifier inputs: Connect the amplifier “Front Input" to the Ride Command "Audio Amp 1" factory harness. Connect the amplifier “Rear Input” for rear speakers to "Audio Amp 2” factory harness.

Front Kick Panels (RZR Turbo S & RZR XP1000 2014+)

Tools Needed for Installation: T-40 Torx Driver, #2 Phillips Screwdriver

Parts List:

1. RZ4-F65 Enclosures (1 pair): Two black speaker pods designed to fit into vehicle kick panels, each with a Kicker speaker mounted inside.
2. #14 Screws x4: Four screws for mounting the speaker pods.

Speaker Pod Routing:

Route the B-H1149 across the dash cavity. The cable marked as “DRIVER” will route under the dash and down to the driver side footwell. The cable marked "PASSENGER” will route over the top and down the right side of the factory glovebox.

1. A. Remove factory screw: Starting at the driver side footwell, remove the factory T40 torx screw as shown. Save this screw for Step D.
2. B. Position kick pod: Place the driver kick pod into location so that both vehicle screw bosses line up with kick pod brackets.
3. C. Secure kick pod: Using two #14 screws, loosely secure the kick pod to the factory screw bosses.
4. D. Bolt kick pod bracket: Re-use the factory T40 torx screw previously removed in Step A to loosely bolt through the lower kick pod bracket to the vehicle panel. Once all three screws are in place, go back and re-tighten.
5. E. Connect speaker cable and secure: Connect the B-H1149 cable to the speaker pod and zip tie all cables to the frame.
6. F. Connect speaker harness to amplifier: Connect the B-H1149 speaker harness to the 300.4 amplifier front output.
7. G. Install passenger pod: Repeat Steps to install passenger kick pod.

Connecting Power & Ground Cable to Battery

1. A1-A3. Fuse holder assembly: Remove the bottom cover of the fuse holder by extracting the 2 screws. Break off the right and left side tabs on the bottom cover. Extract both fuse holder screws. Attach both the Power Wire and Battery Terminal Cable to the fuse holder. Reattach the bottom cover.
2. B. Connect ground cables: Unscrew the factory nut on the negative battery terminal. Install the 2 ground cables to the screw on the ground battery terminal. Re-install the factory nut.
3. C. Connect power cables: Unscrew the factory nut on the positive battery terminal. Install the 2 power cables to the screw on the positive battery terminal. Re-install the factory nut.
4. D. Install fuse: Remove the top of the fuse holder and extract the 2 screws. Insert the 40A fuse, screw the 2 screws back in and reattach the fuse holder top.
5. E. Manage cabling: Zip tie all of the electrical cabling (factory and audio) along the center column away from the drive shaft.

This concludes the installation process. Replace the factory panels and seats.

Questions? Please contact SSV Works at 818-991-1778 or email support@ssvworks.com

Antenna Relocation (If Equipped)

If your vehicle is equipped with a V2V antenna (Photo A), SSV Works recommends relocating the antenna underneath the hood in front of the radiator (Photo C) to avoid amplifier interference.

Looking for More Sound? Try SSV Works Cage Mount 6.5" Speaker Pods!

SSV Works custom molded Cage Mount Pods are designed for 6.5" speakers and can be used when you need more sound in your Side by Side. Unlike wakeboard towers, these mini pods are designed to provide sound to the passengers without blocking visibility. They are 100% fiberglass for the best sound quality and bass response. They are finished in a black texture coat to match factory interior textures and can be custom painted to match your color scheme. Includes the versatility of Axia Alloys patented clamping system and stainless mounting hardware.

Call 818-991-1778 to order yours today!

Part Number US2-C65