User Guide for ABILITY models including: VS68200 AI-Eye 8M Fixed Lens Dome Network Camera, VS68200, AI-Eye 8M Fixed Lens Dome Network Camera, Lens Dome Network Camera, Network Camera, Camera
Ability Enterprise Co., Ltd.
AI IP Camera Quick Start Guide 2.7 Wall Mount Installation with wall mount stand Step 1 Use a 5mm drill bit to drill four 35mm deep holes in the positions marked by the drilling sticker. Use a hammer to
File Info : application/pdf, 25 Pages, 1.16MB
DocumentDocumentAI-Eye 8M Fixed Lens Dome Network Camera Quick Start Guide Model: VS68200 AI IP Camera Quick Start Guide 1.1 Accessing via Web Browser Default IP address https://192.168.0.11 User name admin Password AbAi.Camera1 1.2 Appearance Description The overview of the dome camera is shown below: AI IP Camera Quick Start Guide 1.3 Packing list Component Camera Drilling sticker Expansion tube Tapping screw Pieces 1 1 2 2 AI IP Camera Quick Start Guide 1.4 Cable No Item 1 LAN/POE 2 DC 12V+ / DC 12V ALARM_OUT COM 3 ALARM_IN ALARM_GND AUDIO IN/ 4 AUDIO OUT/ AUDIO_GND Description Ethernet/POE connection. This interface supports POE. Power input interface. DC 12V9.0V15.0V Alarm output and COM interfaces. The interface work together to form the alarm output. Alarm input interface. There may be multiple alarm interfaces. For a given number of interfaces, n, they are numbered (for example: ALARM_IN0, ALARM_IN1, ...,ALARM_INn). Each one connects to the ALARM_GND connection to form a single alarm input. Audio input (connect to MIC)/output interface and audio ground interface. AI IP Camera Quick Start Guide 1 2 3 Cable interface 4 AI IP Camera Quick Start Guide 2. Installation Indoor use only and external circuits installed wholly within the same building structure. 2.1 Note 2.1.1Make sure the device in the package is in good condition and all the assembly parts are included. You will need the following: AI IP Camera Quick Start Guide 2.2 Caution Please do not lift a camera by its cable. 2.3 Top cover of the camera removes Use a Trox screwdriver to remove the Top cover of the camera, and lift the cover to open it. Then, you can see the Reset button and an SD card slot. Torx AI IP Camera Quick Start Guide 2.4 Reset Button To restore the camera to factory settings and software reboot the camera, you need to press and hold the reset button 5~10 seconds. To restore the camera to factory settings and hardware reboot the camera, you need to press and hold the reset button more than 10 seconds. Reset Button AI IP Camera Quick Start Guide 2.5 Micro SD card installation The SD card slot supports only class 6 or higher Micro SD card. To replace a Micro SD card, the device must be powered off. Otherwise, system exception may occur. When a Micro SD card is used for the first time, log in to the web client of the device and format the Micro SD card. For details, see the Configuration Guide. Please refer to figure 2.5, insert the memory card to memory card slot on the rear housing of the camera. During SD card installation, you are advised to turn the camera maintenance position upward and insert the SD card into the SD card slot from upon to avoid accidentally dropping the SD card into the camera. SD Card Slot AI IP Camera Quick Start Guide 2.6 Remove the Anti-moisture Sticker Before mounting the camera onto its install position, please remove the antimoisture sticker in the first place to get the air vent start working. AI IP Camera Quick Start Guide 2.7 Wall Mount Installation with wall mount stand Step 1 Use a 5mm drill bit to drill four 35mm deep holes in the positions marked by the drilling sticker. Use a hammer to carefully drive the white plastic expansion tubes into the holes. Then use 2 screws to mount the wall stand onto the wall. Step 2 Place the camera onto the wall-mount bracket such thread the cables through the hole of the bracket as well as. Then use 2 pairs of screw and nut to mount the camera onto the wall-mount bracket. AI IP Camera Quick Start Guide Step 3: Loosen the Philips head screws and adjust the camera to the required angle. Then retighten the screws. Finally, fasten the top cover of the camera. (Note. Depending on the usage and the space limitation, the mounting can be done as the two stances shown in the figures.) Rotator Angle : ± 176 Pan Angle : ± 176 Rotate Angle : ±100 Tilt Angle : 18~100 Downward/Upward Stance AI IP Camera Quick Start Guide 2.8 Cable connection 2.8-1 For safety precautions The lightning arrester must be installed and grounded if you install camera outdoor. Strong and weak current cables must be kept at least 5 cm apart from each other. When connecting the cables to the device, take care to avoid connecting strong current cables to weak current interfaces or you will damage your device. The tail of cable must be cut if it cannot pass through the wall, please keep the label on tail of cable. And please make sure to use insulating tape and waterproof tape to insulate and waterproof all tail of cable to avoid short circuits and water leakage. Wrap all pigtail cables in insulated, waterproof, rubber tape to prevent short circuits or water damage. AI IP Camera Quick Start Guide 2.8-2 Power cable connection Connect the power cable to the device. 2.8-3 Ground cable installation Please connect ground cable of camera to ground. AI IP Camera Quick Start Guide 2.8-4 Audio and alarm cable installation Connect the ground cable to ground the device, and then connect the power cable. If crimp terminals are not used, the wire thickness cannot exceed 1.5mm2, and the length cannot exceed 25m. If crimp terminals are used, the wire can be up to 0.75mm2 for a 15m length of wiring or up to 1.0mm2 if 20m is required. Longer wiring is not supported. The ground impedance cannot exceed 5 ohms. 2.9 Cable waterproof and insulation Waterproof and insulate all cables including power cables, network cables, and unused pigtails. 1. Wrap one layer of insulation tape around each cable joint. 2. Stretch the waterproofing tape evenly to twice its original length. Then apply it for three layers from bottom to top, from top to bottom, and from bottom to top again. 3. Stretch the insulation tape evenly to twice its original length. Then apply it for three layers from bottom to top, from top to bottom, and from bottom to top again.to up. Finally tie the upper and lower ends with cable ties. Then use cable ties to secure the both ends. 4. Cover the rest of the cabling in a conduit or with protective waterproof rubber tape. Make a drip loop as shown below to create an artificial lowest point of the cable. AI IP Camera Quick Start Guide AI IP Camera Quick Start Guide 3. Desiccant Bag Replacement If the camera is experiencing fogging, you will need to replace the existing desiccant bag (The rectangular object inside the camera frame.) 3.1 Identification of Desiccant Bag's Functionality The remained functionality of the desiccant bag can be identified by the color of the silica gel beads among the desiccant, which are: Bright Yellow - Dry Light Green - Some moisture is absorbed AI IP Camera Quick Start Guide Dark Green - A considerable amount of moisture was absorbed To replace the desiccant bag, please follow the steps mentioned in the following sections, and the procedures should be done by the engineering staff. 3.2 Replace the Desiccant Bag Step1 Open the housing and the BoxPan of camera and locate the desiccant bag. The desiccant bag will be attached to the inner surface of the BoxPan. (For more information, please refers to the user's manual of your camera model.) AI IP Camera Quick Start Guide Step2 Remember the place of desiccant bag and remove it.(Note: Be careful, do not exert any pressure in the camera lens or other components.) Step3 Open the aluminum foil pack that is included in the camera box. The desiccant bag is included inside it. AI IP Camera Quick Start Guide Step4 Stick a double-sided tape on desiccant bag. Pull the adhesive tape cover in order to attach the desiccant bag to the camera. (Note: Some of desiccant bags already stick a double -side tape, so just remove the tape cover then attach the desiccant bag to the housing.) Step5 Place the desiccant bag to the same place as the old one. Be sure to press it tightly so that it won't fall after. Step6. AI IP Camera Quick Start Guide Put back the BoxPan & housing of the camera as soon as the bag is replaced. (If you leave it open too long, the desiccant bag will start absorbing water from the environment.) AI IP Camera Quick Start Guide Step7 Be sure the housing is closed tightly. AI IP Camera Quick Start Guide 4. Check Item Please confirm the following to ensure that the equipment is installed correctly. Check Item Result All screw fully tightened YES NO The camera is securely installed to the mount or wall YES NO The ambient temperature meets the device specifications. YES NO Insulation and waterproofing measures have been taken to protect YES NO cables installed in humid environments, and the drip loops are in correct positions. The camera can power on normally. YES NO You can access the camera web portal using the IP address you YES NO configured. On the camera web portal, you can view live video from camera. YES NO You can view the surveillance from camera web pages and the YES NO image is clear, as shown in the following figure. In night vision mode, the surveillance is can be viewed clearly. YES NO AI IP Camera Quick Start Guide Declaration of toxic and hazardous substances in electronic and electrical products AI IP Camera Quick Start Guide FCC compliance statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.