Magene Dual-Protocol Crank Power Meter

01/ Quick Start Guide

Thank you for purchasing the Magene Dual-Sided Crank Power Meter (Hereinafter referred to as Magene Power Meter). For information regarding crank installation and adjustment not covered in this guide, please refer to your bicycle dealer's instruction manual.

Contact Information:

• E-mail: support@magenefitness.com
• Phone: (+86)400-662-8297
• Website: www.magenefitness.com

If you have any questions about the power meter module, please contact Magene customer service.

02/ Unpacking the Box

Take the Magene Power Meter and its parts out of the box and keep the original package for future storing and transporting.

The box should contain:

• (1) Left power crank
• (2) Right power crank
• (3) Charging line
• (4) Quick Start Guide
• (5) Accessory Bag

[Image description: Diagram showing the contents of the box, including left and right power cranks, charging cables, and the quick start guide.]

03/ Connect and Activate the Power Meter

Note: The power meter is not activated and cannot be used normally. The new product must be activated for the first time.

Android users can enter the Google Play Store, and iPhone users can enter the App Store to search for the "Magene Utility" app and download it. Follow the prompts to activate your power meter.

Note: If the activation fails, please click back to enter the device search list and reconnect to activate.

04/ Connect the Power Meter Device

Magene Power Meter can be connected to a power device after activation. Magene Power Meter is a Bluetooth and ANT+ dual-protocol power meter that is compatible with ANT+ and Bluetooth devices that support the standardized power meter protocol. Using this protocol, the power meter's measured data can be viewed and recorded.

Typically, most bike computers can search for and add power meter equipment in the settings via Settings > Sensors > New Sensor > Power Meter.

Note: When searching for the Magene Power Meter, step on the pedal connected to the Magene Power Meter crank so that the power meter can detect the torque, thereby waking up the power meter from Sleep mode. Start the Bluetooth or ANT+ signal broadcast and wait for a device to connect.

Note: If there are multiple power meters in the current environment, you need to identify your power meter by its ANT+ ID.

05/ Calibrating The Power Meter

Zero offset calibration will calibrate the power meter to 0 power when at rest. When calibrating, please turn the left crank to the vertical ground-down state and use an ANT+ Device or MAGENE UTILITY for calibration.

06/ Peripheral Pairing and Functions

Magene Power Meter wirelessly transmits ride information to a bike computer or receiver that supports ANT+ or Bluetooth. Magene Power Meter logs the following information as you ride:

• (1) Power
• (2) Cadence
• (3) Remaining Battery
• (4) Torque Effectiveness
• (5) Pedal Balance
• (6) Pedal Smoothness

This product transmits the following information wirelessly to cycle computers or receivers that support ANT+ or Bluetooth LE connections.

Note: Features 4, 5, and 6 (Torque Effectiveness, Pedal Balance, Pedal Smoothness) can only be used in part of the Magene apps. If you are purchasing the LITE version, features 4, 5, and 6 need to be purchased through Magene Utility.

07/ Charging

When you find that the power meter is unable to search for a connection, the power meter may have run out of power. Please charge it as soon as possible.

Charging procedure:

1. Insert one end of the USB interface of the charging cable into the computer or charger, and bring the magnetic suction head close to the power meter body to make it absorb naturally.
2. Confirm that the red light of the power meter is always on, indicating that the power meter is in a normal charging state. When the battery is fully charged, the light will turn green.

NOTE: Do not short-circuit the magnetic suction end, and do not adsorb on metal when it is electrified. Only use a USB adapter with an output voltage of 5V for charging.

08/ Product Specifications

09/ Troubleshooting

Please refer to the following if you have any questions during the use of Magene Power Meter.

Q: Undisplayed power

A: 1. Check to see if activation has been performed. 2. Check whether the bike computer or software has been connected. 3. If the connection cannot be made, please charge your power meter.

Q: The power has obvious deviation

A: Perform zero offset calibration using your bike computer or Magene Utility.

Q: Zero point calibration failure

A: Please place the bicycle on flat ground, ensure the left crank is straight down, and try again.

Q: Torque Effectiveness/Pedal Balance/Pedal Smoothness of right crank power meter is 0

A: 1. Use the Magene Utility to check if the right side is connected. After static setting the crank for 1 minute, do not touch it. Rotate the crank to see if the connection state is restored. If not, check the battery power. 2. If the problem occurs after a failed upgrade, check that the ID of the right crank (see the ANT+ ID number on the sticker on the crank) appears in the device list. If so, click to connect, upgrade the device, and re-check the connection status.

If none of the above is applicable or the problem is not solved, please consult online customer service or dealers.

10/ Upgrading the Power Meter's Firmware

Android users can enter the Google Play Store, and iPhone users can enter the App Store to search for the "Magene Utility" app and download it.

Use Magene Utility to connect the power meter to obtain the latest firmware.

11/ Warnings and Daily Check

1. Warnings:

• Do not spray the power meter module with high-pressure water when cleaning the bicycle.
• Please tighten the crank and pedal bolts exactly according to the instructions. Otherwise, it may cause damage to the crank or pedal.
• Do not put the battery into fire or heat, otherwise it may cause a fire or explode.
• The power meter module is a splash-proof design. Do not soak the power meter module in water.
• Do not subject the crank and power meter module to severe impact, as this may cause the power meter module to detach or malfunction.
• In temperatures below -10°C, the battery life will decay rapidly.
• Use neutral detergent when washing cranks. Use of alkaline or acidic detergents or thinners may shorten the life of the sensor case.
• The power meter module uses the 2.4G wireless communication band. The 2.4G signal environment surrounding the object or the surrounding area may cause interference to communications.
• If the signal connection is found to be unstable, try again in an open area. Strong electromagnetic waves generated by the surroundings may cause interference.
• Do not try to remove the waterproof glue around the power meter module! This will compromise the waterproof performance of the power meter module.
• Natural wear and aging and normal use caused by performance deterioration are not covered by the warranty.

2. Daily Check Items Before Riding:

Please check the items listed below before riding. In case of any abnormality, it is recommended to seek professional technicians for maintenance and debugging.

• Are there any cracks in the crank arms?
• Are the fastening sections fixed securely?
• Are the bearing sections fixed securely?
• Are there any abnormal noises?
• Is there sufficient charge remaining in the battery?

12/ WARRANTY CARD

Warranty Clause:

Thank you for purchasing the Magene Dual-Sided Crank Power Meter crank-arm power meter. Please carefully read the Warranty Clause.

This product has passed strict quality inspection. For failures caused by product quality problems under normal use, Magene will provide a free warranty within the warranty period.

The warranty period for Magene chainrings is 360 days from the activation date.

The warranty period for Magene power meters and cranks is 720 days from the activation date.

The warranty does not cover any problems caused by conditions, malfunctions, or damage not resulting from defects in material or workmanship. The fees for shipping back to Magene for repair shall not be reimbursed, and no fees shall be charged for Magene shipping back to you.

The following situations are not covered by warranty:

• Beyond the warranty period.
• No valid warranty certificate.
• Damage caused by improper use and maintenance.
• The product code on the warranty card does not match the product.
• Unauthorized maintenance, modification, or use of parts other than the product.
• Damage caused by irresistible factors.
• Damage caused by not using or installing the product in accordance with the instructions.
• Unauthorized alteration of the warranty card.
• Other failures and damages caused by non-product design, manufacturing, quality, etc.
• Wear and dirt caused by normal operation, such as scratches, bumps, etc.

After the warranty expires, Magene continues to provide maintenance services for which related service fees will be charged.

Magene retains the rights to modify and explain the above-mentioned contents.

FCC Warning

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.