Deluxe Flush Electric Toilets
These toilets are engineered to provide the comforts of a home toilet, combining sleek elegance with the features required for luxury marine vessels. Available in 50840/50820 Series.
Discover Jabsco's Complete Range of Waste System Products
Jabsco offers a comprehensive selection of marine waste management solutions designed for comfort, efficiency, and reliability on board.
Twist 'N' Lock™ Manual Toilet
The Twist 'N' Lock™ action safety handle ensures a quick and easy lock, providing a solid seal during voyages. Model numbers: 29090-3000.
New! Diaphragm Waste Pumps
Heavy-duty diaphragm pumps are designed to pass solids easily and quietly, ensuring maximum efficiency when emptying holding tanks. Model number: 50890 Series.
Run Dry Macerator Pump
This pump features a fully sealed motor and a powerful chopping blade with four blades to prevent clogging. Model number: 18590 Series.
Quiet Flush Electric Toilets
Designed to significantly reduce noise levels, these electric toilets enhance comfort for all crew members, even during sleep. Available in 37045/37245 Series.
New! Y-Valve
A robust Y-Valve allows waste to be pumped overboard or into a holding tank. Model number: 45490 Series.
Jabsco Global Contacts & Warranty Information
For more information, visit www.jabsco.com.
The products described herein are subject to the Jabsco one-year limited warranty, available for inspection upon request.
Jabsco is a trademark of Xylem Inc. or one of its subsidiaries. ©2015 Xylem Inc. All rights reserved. Document reference: 950-0526 Rev. C 4/2015.
Global Offices:
- USA: Jabsco, 100 Cummings Center, Ste. 535-N, Beverly, MA 01915. Tel: +1 978 281 0440 Fax: +1 978 283 2619
- UK: Jabsco, Bingley Road, Hoddesdon, Hertfordshire, EN11 0BU. Tel: +44 (0) 1992 450 145 Fax: +44 (0) 1992 467 132
- JAPAN: NHK Jabsco Co Ltd, 3-21-10, Shin Yokohama Kohoku-ku, Yokohama 222. Tel: +81 (0) 45 475 8906 Fax: +81 (0) 45 475 8908
- GERMANY: Jabsco GmbH, Oststraße 28, 22844 Norderstedt. Tel: +49 (0) 40 53 53 73 0 Fax: +49 (0) 49 53 53 73 11
- ITALY: Jabsco Italia, s.r.l., Via Tommaseo, 6, 20059 Vimercate, Milano. Tel: +39 039 685 2323 Fax: +39 039 666 307
Jabsco Type III MSD Waste Management System (Model 38110)
This system is designed for efficient and reliable waste management on marine vessels.
Key Features:
- Rugged Polyethylene holding tank
- Barbed fittings for all hose connections
- Heavy Duty Macerator
- Evacuation pump
- Three run-dry and accidental activation safety features
- Touch-pad waste management control panel
- Additional dock side evacuation pick up
Pump Features:
- Pump:
- Self-Priming Flexible Impeller with Stainless Steel Wearplate
- Impeller:
- Jabsco Nitrile compound
- Macerator:
- Stainless Steel Cutter reduces particle size to 1/8" (3mm) maximum
- Seal:
- Lip Type
- Ports:
- Inlet - 1-1/2" (38mm) Hose Barb and 1-1/2" N.P.T. (Male); Outlet - 1" (19mm) Hose Barb
- Motor:
- Permanent Magnet Type, Fully Enclosed, with Stainless Steel Shaft. Includes Run-Dry Protection Device that shuts-off pump. Powder coated housing with sealed end-bells and bearings.
System Features:
Level Indication: When pressed, the level indicator illuminates for 1 minute. When the tank level reaches full, the indicator flashes automatically to alert the user to empty the tank.
Sleep Mode: If the flashing LED is a disturbance, the unit can be put into sleep mode. The unit will emerge from sleep if the system is turned off or the tank level is increased. Note: The unit is unable to be put into sleep mode if the tank is 7/8 full or greater.
Empty Button: This button needs to be pressed and held for 3 seconds to activate the pump. This eliminates the possibility of accidental operation.
Averaging: Two different level averaging methods are used – one when filling and one when emptying. This compensates for boat movement when the tank is filling, allowing accurate readings when emptying.
Fail Safe Feature: If no fluid movement is sensed 20 seconds after the pump is set to run, the pump will shut down and the fault LED on the indicator panel will flash. This protects the pump from failure. Note: To reset the unit, simply press the level button. If the unit continues to shut down and indicate a fault, check the pump and plumbing for a blockage.
Installation:
- The holding tank should be located as close to the toilet as possible.
- A proper seacock is required if the discharge thru-hull is positioned below the waterline.
- If both the discharge thru-hull and the holding tank are fitted below the waterline, a vented loop must be fitted to prevent a potential siphon being created. If unfamiliar with the installation of a vented loop, consult a marine plumber or contact Jabsco for further details.
- Mount on a strong flat surface. The installation area needs to support the weight of the unit plus its contents. The total weight for this unit when full can equal 90lbs.
- Four mounting feet are supplied. These need to be attached to the platform with four machine or lag screws and flat washers.
Plumbing:
Each tank is fitted with the following:
- 1 x 1½" Deck pump out - Evacuation pick up tube - Fit to dockside pump-out deck plate.
- 1 x 1½" Inlet port - From toilet system.
- 1 x 3" O-ring sealed inspection hatch.
- 1 x 1" Vent* - Connect to vent outlet usually sited high on a vessel's hull near the gunwale.
Electrical Systems:
The unit should be wired into an independent circuit. Refer to the cable sizing and fuse specifications in the wiring table. Consult the wiring diagram for connections.
Wiring Table: Cable Size by Run Length
| Voltage | Amperage | Fuse | 0"-10" | 10"-15" | 15"-25" | 25"-40" | 40"-60" |
|---|---|---|---|---|---|---|---|
| 12 VDC | 16 | 20 | #16 (1.5) | #14 (2.5) | #14 (2.5) | #12 (4) | #6 (16) |
| 24 VDC | 8 | 15 | #18 (1) | #16 (1.5) | #16 (1.5) | #14 (2.5) | #10 (6) |
*Run length is the total circuit length from the power source to the product and back to ground. Cable sizes are indicated in AWG and millimeters.
Maintenance:
To maintain the system in good working order, flush it with clean water to remove any sludge or waste buildup. This process is recommended at least once a year. For macerator pump service, refer to the Service section of the 18590 Series Macerator data sheet.
Winter Storage:
Drain all water from the system, ensuring that the pipes and pump are completely free of residues.
Diagrams and Illustrations:
System Overview Diagram
A schematic diagram illustrating the main components and connections of the Jabsco Type III MSD Waste Management System. Key elements include:
- (1) Battery: Power source for the system.
- (2) Fuse: Electrical protection for the circuit.
- (3) Waste Management System: The central unit.
- (4) Master Switch: Controls the power to the system.
- (5) Waste Management System Controller: The touch-pad control panel.
Typical Installation Diagram
An illustration showing a typical marine toilet and waste system setup. Key components are:
- (1) Vent: For air circulation and pressure equalization.
- (2) Grooved Inlet Port 1-1/2" (38mm): Connection point for waste input.
- (3) Toilet: The marine toilet unit.
- (4) Deck: The boat's deck, where the pump-out connection is located.
- (5) Pump Outlet: Where waste exits the pump.
- (6) Waste Holding Tank: Stores the waste.
- (7) Vertical Loop Outlet: A loop in the discharge line to prevent siphoning.
Exploded View Diagram and Parts List
A detailed exploded view of the Type III MSD Waste Management System, showing individual components and their assembly. The diagram includes numbered parts corresponding to the following list:
| Ref. | Description | Part Number |
|---|---|---|
| 1 | Grooved Collector Tube 1-1/2" (38 mm) | 38111-0000 |
| 2 | Vent 3/4" (19 mm) | 38111-0010 |
| 3 | Vent 5/8" (16 mm) | 38112-0000 |
| 4 | Cap and O-ring | 38115-0000 |
| 5 | Tank | 38113-0000 |
| 6 | Base | 38114-0000 |
| 7 | Tank Control Box (sensors below base) | 38116-0000 |
| 8 | Sensor Arrangement | 38117-0000 |
| 9 | Macerator for 12 V | 18590-2092 |
| Macerator for 24 V | 18590-2094 | |
| Control Cable 4.5 m | 47010-0000 | |
| Control Cable 6 m | 47020-0000 | |
| Control Cable 9 m | 47030-0000 | |
| 10 | Control Panel for 12 V | 38111-0012 |
| Control Panel for 24 V | 38111-0024 |
Control Panel Mounting Template
A template for mounting the control panel, indicating drill pilot holes (4) with a spacing of 2-3/8 inches horizontally and 2-9/32 inches vertically. The template also shows a 5/16 inch diameter hole and a 3/4 inch diameter clearance hole for the connector, positioned 9/16 inch from the edge.
International Product Names & Compliance
The Jabsco Type III MSD Waste Management System (Model 38110) is known by various names internationally:
- FR: Système pour traitement des déchets MSD de type III
- DE: Fäkalien-Entsorgungs-System Typ III MSD
- IT: Sistema di gestione dei rifiuti MSD Tipo III
- NL: Vuilwatersysteem type III MSD
- SE: Typ III MSD-avfallshanteringssystem
- ES: Sistema de gestión de residuos MSD Tipo III
The product bears the CE mark, indicating conformity with relevant European Union directives.
