for MOUNTUP models including: MOUNTUP, Desk Mount, MU0004

打印

Single Monitor Desk Mount

If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of ... 1/5/2021 11:55:31 AM ...

• Google Docs
• Google Drive
• Download [pdf]
• Download Optimized
• Document:
  • Text

File Info : application/pdf, 12 Pages, 4.34MB

Single Monitor Desk Mount
Instruction Manual

MU0004

75x75 100x100

32"

2~8kg 4.4~17.6lbs

If you have any questions , please contact us via: help@jollyholding.com

V7.0

WARNING!
If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product, contact Customer Service via help@jollyholding.com.
Before starting assembly, verify all parts are included and undamaged. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
This product contains small items that could be a choking hazard if swallowed. NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS

A (x1) Upper Arm

B (x1) Lower Arm

C (x1) Base

D (x1) VESA Plate

E (x1) Bracket

F (x1) Clamp

G(x5) M6x10

H(x4) Pad

I (x1) Grommet Base

J (x1) Wingnut

K (x1) Carriage Bolt

L (x1) Bolt

M (x1) Support Plate

N (x1) 3mm Allen Key

O (x1) 4mm Allen Key

P (x1) 6mm Allen Key

M-A (x4) M4x12

M-B (x4) M6x12

17.6lbs (8kg)
DO NOT EXCEED WEIGHT CAPACITY.

M-C (x4) D6 Washer
01

M-D (x4) spacer
NOTE: Not all hardware included will be used.

ASSEMBLY STEPS
STEP 1: Apply Pads to the Base Bottom

Apply pads (H) to the base

bottom to avoid desk scratches.

H

C

10-60mm 10-90mm

STEP 2: Clamp Installation or Grommet Base Installation
OPTION A: Clamp Installation Mount Bracket (E) to Base Bottom (C) with Bolts (G). Bolts could be tightened by the 4mm Allen Key (O). Similarly, attach Clamp (F) to Bracket (E) with Bolts (G) and 4mm Allen Key (O). Adjust the Clamp width to fit with desk. Secure stand to desktop by tightening Clamp (F) or by Allen key (P).
C

E

OR F

G

E

G O

G O

O

OR

F

P

02

STEP 2: (Continued)
OPTION B: Grommet Base Installation For grommet hole mounting, place Carriage Bolt (K) through the center of Grommet Base (I). Mount Grommet Base to Base Bottom (C) with Bolts (G) and tighten by 4mm allen key (O). Run Carriage Bolt (K) through Grommet Hole on desktop. Attach Support Plate (M) and Wingnut (J). Last step, tighten Wingnut (J).

C I K

G O

M J
03

10-90mm

STEP 3: Arm Installation
Install the lower arm (B) and the upper arm (A) to the base (C). Secure the arm by tightening the inside screw using 3mm Allen key (N).

C F

B N

DO NOT tighten the screw excessively or it might be stripped.

DO NOT tighten the

A

screw excessively or

it might be stripped.

N
Note: Please note that the side with the label"" is installed on the base(C) when installing the lower arm(B) to the base (C).

04

STEP 4: Attach Monitor
OPTION A: Flat Back Monitor
Attach the VESA plate (D) to back of monitor and secure with screws(M-A)or(M-B) with washers(M-C) using 6 mm Allen Key (P). Do not tighten the screws excessively or your monitor might be damaged. .

M-A

M-B

P

D M-C
CAUTION:To select the correct screws(M-A or M-B) for your monitor, you can try to screw it on your monitor by hand. The one can screw inside is the correct screw for your monitor.
OPTION B: Curved Back Monitor
Attach the VESA plate (D) to back of monitor and secure with screws (M-A) or (M-B) with washers (M-C)and spacers(M-D)using 6 mm Allen Key (P). Do not tighten the screws excessively or your monitor might be damaged.

M-D

M-A

M-B

P

D

M-C

05

STEP 5: Hang Monitor
Slide the monitor onto the head of swivel arm, install the security bolt (L). Make sure the security bolt is installed before you rotate the monitor.

L
Important Notice: The gas spring tension is pre-set to the weakest level by default, please hold your monitor by both hands and do not let go so soon after the VESA plate is attached to the swivel arm. It's suggested to loose hold of the monitor in a slow & gentle way while observing if the gas spring arm falls down greatly.
Refer to below illustrations to adjust tilting angle of your monitor.
Tilts down

P
06

Note: 1. Loosen the tilting bolt. 2. Adjust monitor to your
desired tilting angle. 3. Retighten the tilting bolt to

STEP 6: Adjust Tension
For proper functioning of this mount, depending on different weight of monitor you might need to adjust tension in upper arm (A) using 6 mm allen key (P).
P

CAUTION
Note1:
Be sure to keep the arm in horizontal position during adjustment.

Falls down

After being attached to the arm, the monitor falls down and can not stay at the desired height by itself.
Turn counter-clockwise("+"direction) to increase gas spring tension until the monitor can stay at the desired height by itself.

Rises up

After being attached to the arm, the monitor rises up and can not stay at the desired height by itself.
Turn clockwise("-"direction) to reduce gas spring tension until the monitor can stay at the desired height by itself.

Note2:
As for how many circles the screw should be turned, the table below is for reference.

Monitor Weight

2kg 3kg 4kg 5kg 6kg 7kg 8kg

Circles (AT LEAST) min

1

4

8

11

14

17

07

STEP 75: C(aCbolnetMinauneadg) ement
Remove bottom plastic covers from gas spring arm as shown in diagram.
Run cables from monitor through bottom of gas spring arm. Reattach plastic covers as shown in diagram.
08

Adjust as Desired
Adjust monitor position and rotation.
360° 360°

180° 360°

+90° -45°

DESK

DESK

Pay attention while clamp install !

09

3.9" 0.39-3.5"
2.9" 3.9" 4.5" 6.9"-16.9"

Product Dimensions

6.3"

7.2"-10.2"

2.5"

180°

360°

2.9" 3.9" 4.5"
360°

+90° -45°

360°

10

CAUTION AND MAINTENANCE:
· Never allow children to climb, stand, hang, or play on any part of monitor or stand. · This product is intended for indoor use only. Using this product outdoors could lead to
product failure and personal injury. · Check that the bracket is secure and safe to use at regular intervals (at least every three months).
If you have any questions, please contact us.
help@jollyholding.com