Magnadyne - Entertaining your RV travels for over 50 years
magnadyne.comALA-21P Instructions
Installation Guide for CARBINE models including: 76CSR, Remote Start with Security and Keyless Entry System
Pin. Color. Function. Pin. Color. Function. 1. White/Violet. (-) 2nd Unlock Output. 14. Black/Yellow. (-) Dome Light Supervision Output.
Nutek Corporation MTRUF Transceiver ELVMTRUF ELVMTRUF mtruf
File Info : application/pdf, 2 Pages, 437.21KB
DocumentDocument® REMOTE START with SECURITY & KEYLESS ENTRY SYSTEM FOR PROFESSIONAL INSTALLATION ONLY! If you are not proficient in the installation of this product or would like a full version of the installation manual, please visit our web site @www.magnadyne.com Receiver/Control Center(RCC) Fortin or iDatalink Bypass Module 2nd Sensor Port Green: (+) Starter Input Violet: (+) Start Output Red / Black: (+) Battery Input (1) 20A Orange: (+) Accessory Output Pink / Black: (+) Ignition 2/ Acc Isolation Red / White: (+) Igniton 2/ Flex Relay 20A Pink / White: (+) 2nd Ignition or 2nd Accessory Output Pink: (+) Ignition Input/Output Red: (+) Battery Input (2) 20A Red: +12V Battery Power 15A Brown: (+) Siren Output Black: System Main Ground White: Parking Light Relay Output White: Parking Light Relay Power Input 10A 26 PIN (see chart) Blue: - Negative Door Unlock Output Green: - Negative Door Lock Output 26 25 24 23 22 21 20 19 18 17 16 15 14 26 Pin Harness Pin Color 1 White/Violet 2 Red/White 3 Orange 4 Brown 5 Gray 6 Black/White 7 Blue 8 White/Blue 9 Gray/Black 10 Violet 11 Green 12 EMPTY 13 Violet/White 13 12 11 10 9 8 7 6 5 4 3 2 1 Function (-) 2nd Unlock Output (-) Channel #3 Output (-) Ground When Armed (+) Brake Switch Shutdown (-) Hood Pin Shutdown (-) Parking Brake Switch Input (-) Instant trigger Trunk/Hood pin input (-) External Activation Input (-) Diesel What to Start Input (+) Door Trigger Input (-) Door Trigger Input No Connection (AC) Tach Input Pin Color Function 14 Black/Yellow (-) Dome Light Supervision Output 15 Blue/White (-) 2nd Status or Rear Defog Output 16 Dark Blue (-) 1st Status Output 17 Green/White (-) Re-Arm the Factory Alarm Output 18 Lt. Green/Black (-) Disarm the Factory Alarm Output 19 Brown/Black (-) Horn Output 20 Orange/Black (-) AUX Channel #6 Output 21 White/Black (-) AUX Channel #5 Output 22 Violet/Black (-) AUX Channel #4 Output 23 Violet/Yellow (-) Starter Output 24 Orange/White (-) Accessory Output 25 Pink/White (-) 2nd Ignition or Acc Output 26 Pink (-) Ignition Output Quick Reference Install Guide Mounting the Receiver/Control Center (RCC): 1. Choose a location on the upper or sides of the vehicle windshield. A higher location is best. 2. Remove the backing liner from the mounting tape on the backside of the RCC and stick it to the windshield glass. 3. Route the RCC cable to the location of the control module. Programming System Features: All CARBINE remote start systems have a menu of features that can be programmed to suit the installation requirements of any vehicle. These features can be set by using the RCC button learning procedure or by Windows PC programming and the CARBINE web app. Feature Programming by RCC Button 1. Open the driver's door. 2. Turn the ignition key ON then OFF. 3. Within 5 seconds, press and hold the RCC button to select the menu. - A single chirp indicates Menu #1. - Hold the button longer for two chirps. You are in menu #2. - Continue holding the RCC button for three chirps. You are in menu #3. 4. When the desired menu is reached, release the RCC button. 5. Within 5 seconds, press and release the RCC button the number of times corresponding to the feature you want to change then press and hold the button once more to lock the feature. The siren / horn will chirp to match the feature selected. Release the RCC button. Note: RCC switch pushes are sequential. For example, if you start at feature #1, then push and release the valet switch 2 more times, you will be at feature #3 and so on. Always remember to push and hold the valet switch one more time after each selection to lock the feature before using the transmitter to change the setting. 6. Use the or buttons on the CARBINE remote to adjust the feature. 7. For features with only two options, the (lock icon) = 1 Chirp setting, while the = 2 Chirp setting. 8. For features with more than two settings, the button selects the settings in ascending order. Press and release the button as many times necessary to adjust the feature. 9. The horn/siren will chirp indicating which setting is selected. 10.Turn the ignition key to ON to exit feature programming. Menu #1 (Default in Bold) Chirps Item Feature 1 2 3 4 5 6 789 1 Data Protocol ADS Fortin 2 Confirmation Chirps On Off 3 System Arming Active Passive 4 Door Locking Mode Active Passive 5 Forced Passive Arming On Off Ignition Key 6 Controlled Off On Locking Ignition Key 7 Controlled Off On Unlocking 8 Panic with Ignition On Off On Menu #1 continued (Default in Bold) Chirps Item Feature 1 2 3 456 9 Armed While Driving Off On 10 Auto Starter Disable On Off 11 Door Lock 0.8 Pulse sec 3.5 sec 0.4 Sec 12 Horn Output 20 ms 30 ms 40 50 Panic ms ms Only 13 Horn Honk Mode Pulsed Constant 14 Comfort Closure Off CC1 CC2 15 Tilt Sensor Adjust 3* 1.5* Off 789 Menu #2 (Default in Bold) Chirps Item Feature 1 2 3 4 5 6789 1 Progressive Door Trigger On Off 2 Nuisance Prevention Circuit On Off 3 Valet Switch Pulse Count for Override 1 Pulse 2 3 4 5 Pulses Pulses Pulses Pulses 4 Door Trigger Error Chirp On Off 5 Double Pulse Unlock Off On 6 Double Pulse Lock Off On Ignition Key 7 Controlled On Off Dome Light 8 Siren Duration 30 sec 60 sec Factory Alarm 9 Disarm with On Off Trunk Release 10 Factory Alarm Disarm Pulse Single Double 11 Factory Alarm With Disarm Unlock Before Unlock Remote Start Only 12 Channel #4 Linking None Arm Disarm Remote Start 13 Channel #4 Output Type Button Hold Latched Latched Off with ignition 30 sec 60 90 sec sec 14 Channel #5 Linking None Arm Disarm Remote Start 15 Channel #5 Output Type Button Hold Latched Latched Off with ignition 30 sec 60 90 sec sec 16 Channel #6 Linking None Arm Disarm Remote Start 17 Channel #6 Output Type Button Hold Latched Latched Off with 30 Sec ignition 60 sec 90 sec Menu #3 (Default in Bold) Item Feature 1 2 Chirps 3 4 5 6 789 1 Transmission Type Automatic Manual 2 Engine Checking Mode Wireless Tach Voltage Wired Tach Off 3 Cranking Duration 0.6 Sec 0.8 sec 1.0 sec 1.2 sec 1.4 sec 1.6 sec 1.8 2.0 4.0 sec sec sec 4 Remote Start Run 12 24 60 Time Minutes Minutes Minutes 5 Anti-Grind Output On Off 6 Wired Diesel Start Delay Wait to Start Timer 15 sec Timer Timer 35 sec 45 sec ACC Output 7 During Diesel Off On Wait to Start 8 2nd Ignition Behavior Ignition 1 Accessory 9 Blue/White Wire Function Ground Rear DeWhen fog Latch Running 10 min Rear Defog Pulse 10 External Remote Start Trigger Pulse Count 1 Pulse 2 Pulses 11 Parking Light Behavior Constant Flashing 12 Timer Mode Run 12 3 6 9 Time Minutes Minutes Minutes Minutes 13 Turbo Timer Run 1 3 5 10 Time Minute Minutes Minutes Minutes 14 Timer Start Mode Timer Start Temp Start Access another feature within the same menu 1. RCC switch pushes are sequential. For example, if you start at feature #1, then push and release the valet switch 2 more times, you will be at feature #3 and so on. 2. Press and hold the RCC button after your selection. The siren/horn will chirp to match the feature selected. 3. Use the and buttons on the remote to adjust the feature. Access another menu 1. Press and hold the RCC Button. 2. After 3 seconds, the system will advance to the next menu and confirm with siren/horn chirps. Exiting the feature program mode 1. Set the ignition key to ON. A long confirmation chirp will be heard if a horn or siren is connected. 2. Automatic after 30 seconds with no input from the RCC button (long chirp). Feature Programming by PC/Web All CARBINE Security and Remote Starter Systems with programmable features can programmed using a PC computer (excluding the 32CS model). 1. A Windows computer with internet support is required. The web interface supports Windows 7 (sp1) thru Windows 10 operating systems (Apple/Mac computers are not supported) 2. The web interface supports Microsoft Edge and Google Chrome browsers. 3. The USB programming adaptor model #ALA-21P is required. 4. Navigate to https://magnadyne.com/ala-21p-instructions and register an account. 5. Follow the instructions provided on the webpage and install any dongle drivers or browser updates recommended. Engine Checking Mode: The engine checking mode on all CARBINE remote start systems is set at "Voltage" by default. Once all the wiring is complete and correct, the engine can be remote started without any other changes. Engine type, Extreme weather etc. may require a more defined type of engine checking for reliable operation. Use the information enclosed to setup alternate engine checking modes. Hardwire Tach or Data Tach - Hardwire Tach requires the Lt.Violet/White wire to be connected to a fuel injector wire or a coil wire. - Check the data bypass module spec to make sure it will provide a data tach signal. Additional pre-programming of the data module may be required. Refer to the data module instructions. To learn the tach signal 1. Start the vehicle with the key. 2. Within 5 seconds, press and hold the valet button on the RCC. 3. Once the tach signal is learned, the blue LED on the RCC will light or flash. - When tach learning from a hardwire connection, the parking lights will flash one time - When tach learning via the data module, the parking lights will flash two times. Note: Depending on the data bypass module used, you may have to put the bypass module into tach learning mode first before performing the above procedure. Review the instructions of the data bypass module before proceeding. Wireless Tach Learning To program Wireless Tach 1. After the installation is completed, use the CARBINE key fob and initiate the remote start sequence. 2. If the engine does not start on the first attempt, let the CARBINE module cycle and attempt to start the engine again. Up to (3) cranking attempts may be needed to start and run the engine. 3. When the engine starts and runs, let it run for at least 30 seconds. 4. Use the CARBINE key fob to shut down the engine. Wireless Tach is programmed. Remote Start Shutdown Diagnostics If the remote starter activates but the engine fails to remain running, a diagnostic procedure can be run to try and determine where the fault in the system is. To Perform Shutdown Diagnostics 1. With the ignition key Off, press and hold the RCC button. 2. While holding the RCC button, turn the ignition key On then Off. 3. Release the RCC button. 4. Press and release the RCC button one time. The RCC LED will report the last shutdown reason for 1 minute or until the ignition key is turned On again. Compare the LED flashes to the chart below. Status LED Flashes 1 2 3 4 5 6 7 9 10 11 Reason for Shutdown Over-Rev Shutdown Runtime Expired Shutdown by Transmitter (or Optional Push button) Low or No RPM Detection Hood Open Shutdown (+) Brake Shutdown (-) Parking Brake Shutdown Low Vehicle Battery (Voltage Checking Mode Only) Wait-to-Start Alarm Trigger During Remote Start Programming the Digital Shock Sensor: Follow the enclosed procedure to set the sensitivity of the digital shock sensor. Note: The pre-warning sensitivity adjusts in proportion to the shock sensitivity. 1. Set the system in disarmed mode. 2. Turn the ignition key ON/OFF 3 times (ending in off). 3. Within 5 seconds, press + buttons together for 2 seconds. The horn/siren will emit (1) long chirp to indicate you are in Shock Sensor Sensitivity Adjustment Mode. 4. To increase sensitivity, press the button. Each time you press the button you will hear (1) chirp. When you reach the MAX level adjustment, you will hear 1 short + 1 long chirp. 5. To decrease sensitivity, press the button. Each time you press the button you will hear (2) chirps. When you reach the MAX level adjustment, you will hear 2 short + 1 long chirp. 6. The shock sensor has 20 steps available for adjustment. The default setting is 10. 7. To return the shock sensor back to it's default setting, press and release the button. You will hear 3 chirps. 8. During the process you can test by knocking: 1short chirp - prewarn; 1 Long chirp - TRIGGER To exit the Shock Sensor Sensitivity Adjustment Mode, turn the ignition key on. You will hear 3 long chirps. Reset and Deletion: If the programmable features need to be reset to default or the Wireless Tach feature needs to be reset for re-programming, follow the enclosed procedure. 1. Open at least one door on the vehicle 2. Turn the ignition key to the ON position 3. Within 5 seconds, press and release the RCC button the number of times required below to perform the task. - Press and release the RCC button two times to delete all of the programmed remote controls. - Press and release the RCC button three times to delete all features programming back to their default settings. Note: This procedure does not erase Wireless Tach information. - Press and release the RCC button four times to erase all pre-learned Wireless Tach information. 4. Once you have selected the function you want to perform, press and hold the RCC button. The RCC LED will flash and the horn will chirp (if connected) to confirm the functional step chosen. Do Not release the button. 5. Press and release the button of a programmed re¬mote. The horn will chirp to confirm the feature has been reset/deleted. 6. Release the RCC button and turn off the ignition key. The siren/horn will chirp (if connected) to confirm exit. Magnadyne Corporation 1111 W. Victoria Street Compton CA 90210 (310) 735-2000 For Warranty Information: Please Visit Our Website at www.magnadyne.com IM_QS-76CSR