Maximum Controls MANUFACTURER OF BRUSHLESS DC SLIDE GATE OPERATORS, SWING GATE OPERATORS AND LONG-RANGE WIRELESS INTERCOMS
Installation Guide for MAX models including: Max-WETX, Max-WERX, Max-WETX Wireless Edge 900, Max-WETX, Wireless Edge 900, Edge 900, 900
Maximum Controls, LLC WI-EDGE-900
File Info : application/pdf, 15 Pages, 11.41MB
DocumentDocumentQUICK INSTALLATION GUIDE MAX WIRELESS EDGE 900 RESIDENTIAL / COMMERCIAL / INDUSTRIAL APPLICATION 200 FT RANGE Max Wi Tx Edge 1 Max-WETX 10K Opening Edge (Sold Separately) Max Wi Edge Receiver Max-WERX Max Wi Tx Edge 2 Max-WETX 10K Closing Edge (Sold Separately) MAX Wi Edge Kit Works exclusively with Max Gate Operators Maximum Controls LLC · 949.699.0220 10530 Lawson River Ave. Fountain Valley CA 92708 · www.MAX.US.com TABLE OF CONTENTS Max Wireless Edge Wi Edge KIT Overview 3 Wi Edge Receiver Installation Overview 4 Installing Opening 10k Edge using Wi Tx Edge 1 5 Installing Closing 10k Edge using Wi Tx Edge 2 6 RF Channel Selection 7 RF Power Lever Selection 8 Troubleshooting 9 TECHNICAL DATA Operating range Operating frequency Response time Environmental rating Power supply Battery Type Current draw MAX-WETX Up to 200 ft. (line of sight) 915 MHz 100ms UL 325 Compliant MAX-WERX Up to 200 ft. (line of sight) 915 MHz 100ms UL 325 Compliant 12 VDC (From Matrix III 10K UL Sensor Port) AA8 Lithium batteries Energizer "Ultimate Lithium" (3500 mAH) NA 70 mA Operating temperature -10°...156°F -10°...156°F Dimensions (L x W x H) 2.25" d x 1"w x 7.125" h 1.625" d x 2.5"w x 4.5" h Weight 0.3 lbs 0.8 lbs Battery life Approximately 2 years * Only use the specified battery type listed above. (ENERGIZER L91 Ultimate Lithium) 2 MAX WIRELESS EDGE 900 MAX WIRELESS EDGE KIT OVERVIEW Max Wi Tx Edge 1 Max-WETX Max Wi Tx Edge 2 Max-WETX EDGE 1 RF CHANNEL RANGE OK LED TX OFFLINE ERROR STATUS LEDs PAIR OK LED (EDGE 1) PAIR BUTTON WITH TX EDGE 1 LED ON WHEN TX EDGE 1 IS TRIGGERED HOUSING BATTERY HOLDER 200 FT RANGE (LINE OF SIGHT) Max Wi Edge Receiver Max-WETX PAIR POWER PAIR OK LED BUTTON PLUG EDGE 2 RF POWER LEVEL (HI OR LOW) RANGE OK LED TX OFFLINE ERROR STATUS LEDs PAIR OK LED (EDGE 2) PAIR BUTTON WITH TX EDGE 2 LED ON WHEN TX EDGE 2 IS TRIGGERED POWER LED MAX WI EDGE RECEIVER MAX WIRELESS EDGE 900 3 MAX WIRELESS EDGE RECEIVER INSTALLATION A Max Wi Edge Receiver module can communicate with two wireless edge transmitters. For instance one for OPENING direction and one for CLOSING. Wi Tx Edge 1 can be used for OPENING 10k Edge and Wi Tx Edge 2 for CLOSING 10k Edge. WI EDGE RECEIVER with mounting bracket (provided) INSTALLING WI EDGE RECEIVER ON MAX SLIDER OPERATOR 1 Mount Wi Edge Receiver with bracket to the back metal plate of Max Slider Operator. Wi Edge Receiver can be installed facing right or left direction depending on gate configuration 2 Align the hole of Wi Edge Receiver bracket with the hole of the slider back bracket and secure it using screw provided 4 MAX WIRELESS EDGE 900 INSTALLING OPENING 10K EDGE USING TX EDGE 1 SINGLE GATE 3 Plug Wi Edge Receiver connector with adapter board to "Module Port" of Matrix III MATRIX III 4 Plug cable with blue connector to "UL Sensors 10K" port EDGE 1 Wi Tx Edge EDGE 2 5 Install Wi Tx Edge on gate so it is in line-of-site with Wi Edge Rx MAX WIRELESS EDGE 900 NOTE Latest Matrix 3 boards are compatible with Max Wireless Edge 900; prior boards without the yellow sticker require factory programming. 5 10K Opening Edge sensor Wi Tx Edge 1 INSTALLING OPENING 10K EDGE USING TX EDGE 1 SINGLE GATE INSTALLING OPENING 10K EDGE 1 Install the OPENING 10K edge sensor on the gate 2 Mount the Wi Tx Edge 1 housing next to the 10K Edge on the front side of the gate using self tapping screws 3 Loosen bottom 2 screws and pull down plug to remove it EDGE 10K 6 Connect the 10K edge wires to the Wi Tx Edge 1 circuit board, screw terminals. (Feed 10k Edge wires through plug first) Slide circuit board back into housing. 7 Push the PAIR BUTTON on the Wi Tx Edge 1 circuit board. Pair LED will start PAIR PAIR LED Button blinking 8 Go to the Wi Edge Receiver and PUSH the PAIR BUTTON for Edge 1. PAIR LED for Edge 1 will become solid when pairing process is successful. Troubleshooting: if PAIR LED keeps blinking, pairing has failed. Ensure Wi Tx Edge 1 is within range of Wi Receiver. 6 4 Remove Wi Edge Tx circuit board by sliding it out of housing (remove board by gently pulling down the jumper cable on the connector) 5 Install 2 batteries on circuit board following battery orientation on battery holder. Power LED will turn ON 9 Reattach PLUG to housing and secure it with 2 screws (provided) Check if the RF Channels of Wi Edge Rx matches RF channels of Wi Edge Tx (see page 7). For additional info check troubleshooting page. MAX WIRELESS EDGE 900 10K CLOSING Edge sensor Wi Tx Edge 2 INSTALLING CLOSING 10K EDGE USING TX EDGE 2 SINGLE GATE INSTALLING CLOSING 10K EDGE 1 Mount the CLOSING 10K edge sensor on the gate and secure position. 2 Mount the Wi Tx Edge 2 housing next to the 10K Edge on the front side of the gate using self tapping screws 3 Loosen bottom 2 screws and pull down plug to remove it EDGE 10K 6 Connect the 10K edge wires to the Wi Tx Edge 2 circuit board screw terminals. (Feed 10k Edge wires through plug first) Slide circuit board back into housing. 7 Push the PAIR BUTTON on the Wi Tx Edge 2 circuit board. Pair LED PAIR PAIR LED Button will start blinking 8 Go to the Wi Edge Receiver and PUSH the PAIR BUTTON for Edge 2. PAIR LED for Edge 2 will become solid when pairing process is successful. Troubleshooting: if PAIR LED keeps blinking, pairing has failed. Ensure Wi Tx Edge 2 is within range of Wi Receiver. MAX WIRELESS EDGE 900 4 Remove Wi Edge Tx circuit board by sliding it out of housing (remove board by gently pulling down the jumper cable on the connector) 5 Install 2 batteries on circuit board following battery orientation on battery holder. Power LED will turn ON 9 Reattach PLUG to housing and secure it with 2 screws (provided) Check if the RF Channels of Wi Edge Rx matches RF channels of Wi Edge Tx (see page 7). For additional info check troubleshooting page. 7 Wi Tx Edge Wi Tx Edge INSTALLING OPENING 10K EDGE USING TX EDGE 1 ENTRY/EXIT AND DUAL GATES ENTRY / EXIT ADJACENT GATES ENTRY GATE 1 Set ENTRY GATE Wi Edge Rx & Tx 1 and 2 on RF CHANNEL 1 refer to next page for instruction EXIT GATE 2 Set EXIT GATE Wi Edge Rx & Tx 1 and 2 on RF CHANNEL 2 refer to next page for instruction PRIMARY / SECONDARY GATES Wi Tx Edge Wi Tx Edge 10K Opening Edge sensor PRIMARY 1 Set PRIMARY Wi Edge Rx & Tx 1 and 2 on RF CHANNEL 1 refer to next page for instruction 8 SECONDARY 2 Set SECONDARY Wi Edge Rx & Tx 1 and 2 on RF CHANNEL 2 refer to next page for instruction MAX WIRELESS EDGE 900 RF CHANNEL SELECTION SINGLE GATE Select a different RF Channel if you have the following conditions: 1) Entry/Exit Gates or nearby adjacent gate that also has Wi Edge 900 installed 2) Dual Gates. Secondary gate that also has Wi Edge 900 installed 3) "Tx Offline" LED turning ON intermittently 4) "Range OK" LED turning OFF intermittently 1 SELECT RF CHANNELS On Wi EDGE Rx 1 - 915 MHz 2 - 920 MHz 3 - 925 MHz 2 Power Cycle Wi Edge Rx. Unplug/Plug IN both Matrix III 10k Port and Module Port 3 SELECT MATCHING RF CHANNEL ON Wi Tx Edge 1 & 2 1 2 3 4 CHNL 1 2 3 4 CHNL 1 2 3 4 CHNL NO JUMPER 915 MHz 1 234 920 MHz 1 234 JUMPER 3 - 4 925 MHz 1 234 JUMPER 2- 3 4 Power Cycle both Wi Edge Tx 1 & 2 by removing and reinstalling batteries 5 Pair Wi Edge Rx with Tx 1 & 2 MAX WIRELESS EDGE 900 9 PAIRING WI EDGE RX AND WI EDGE TX 1 & 2 1 Unpair Wi Edge Rx from Wi Edge Tx 1 & 2 PRESS and HOLD the PAIR BUTTON on Wi Edge Rx until Pair OK LED turns OFF (do this for Edge 1 & 2) 2 PRESS and HOLD the PAIR BUTTON on the Wi Tx Edge 1 until PAIR LED turns OFF. Pair LED will start blinking 3 PRESS and HOLD the PAIR BUTTON on the Wi Tx Edge 2 until PAIR LED turns OFF. Pair LED will start blinking 4 Power cycle Wi Edge Tx 1 & 2 by removing and reinstalling their batteries 5 Push the PAIR BUTTON on the Wi Tx Edge 1 circuit board. Pair LED will start blinking PAIR PAIR LED Button PAIR PAIR LED Button PAIR PAIR LED Button Go to the Wi Edge Receiver and PUSH 6 the PAIR BUTTON for Edge 1. PAIR LED for Edge 1 will become solid when pairing process is successful. Troubleshooting: if PAIR LED keeps blinking, pairing has failed. Ensure Wi Tx Edge 2 is within range of Wi Receiver. Check if the RF Channels of Wi Edge Rx matches RF channels of Wi Edge Tx (Refer to RF Channels Selection page). For additional info check troubleshooting page. 7 Repeat steps 5 and 6 to PAIR Wi Tx Edge 1 to Wi Edge Rx MAX WIRELESS EDGE 900 10 RF POWER LEVEL SELECTION OPTIONAL FEATURE Lower "RF POWER" settings to reduce crosstalk between adjacent gates that have Wi Edge 900 Installed Power Output Max 1 SELECT RF POWER OUTPUT (HI / LO) ON Wi EDGE RECEIVER Power Output Min 2 SELECT RF POWER OUTPUT (HI / LO) ON WI TX EDGE 1 OR 2 1 2 3 4 RF PWR NO JUMPER Pwr HI (Max) 1 234 Pwr LO (Min) 1 234 JUMPER 3 - 4 11 MAX WIRELESS EDGE 900 PAIRING ISSUES TROUBLESHOOTING SYMPTOM POSSIBLE CAUSE SOLUTION Unable to PAIR Wi Tx Edge 1 (or 2) to Wi Edge Rx 1) Wi Tx Edge 1 (or 2) could be already paired. Need to unpair Wi Tx Edge 1 (or 2) from its original Wi Edge Rx 2) Wi Tx Edge 1 (or 2) are too far away from Wi Edge Rx. 1) To unpair them, press PAIR button on Wi Tx Edge 1 (or 2) for at least 5 sec. Then press corresponding PAIR button on Wi Edge Rx also for at least 5 seconds. Try pairing again by following pairing sequence. (See p 5-6) (Power cycle Wi Tx Edge 1 (or 2) - If necessary) 2) Move Wi Tx Edge 1 (or 2) closer to Wi Edge Rx. Try pairing again by following pairing sequence. (See p 5-6) Pair LED Blinking Wi Edge Rx or Tx Tx or Rx PAIR LED Blinking indicate pairing mode Pair with corresponding device Rx or Tx (Refer to pairing on page 5, 6 ) "TX OFFLINE" LED is ON for Edge 1 (or 2) 1) Wi Tx Edge 1 (or 2) is not powered ON. Battery is not installed or batteries are low 2) Wi Tx Edge 1 (or 2) is out of range of the Wi Edge Rx 3) Wi Tx Edge 1 (or 2) is NOT paired to Wi Edge Rx 1) Install or replace batteries on Wi Tx Edge 1 (or 2) 2) Move Wi Tx Edge 1 (or 2) closer to Wi Edge Rx (Refer to pairing on page 5, 6) "EDGE NOT DETECTED" LED is ON for Edge 1 (or 2) 10K Edge is not detected on Wi Tx Edge 1 (or 2). Install a 10K Edge on Wi Tx Edge 1 (or 2) ERROR STATUS LED'S "BATTERY LOW" LED is ON for Edge 1 (or 2) Low battery condition detected on Wi Tx Edge 1 (or 2) (Battery Voltage less than 2.7V) Replace batteries on Wi Tx Edge 1 (or 2) MAX WIRELESS EDGE 900 12 RANGE STATUS LED SYMPTOM TROUBLESHOOTING POSSIBLE CAUSE SOLUTION "RANGE OK" LED is OFF for Edge 1 (or 2) Poor range is detected between Wi Edge Rx and Wi Tx Edge 1 (or 2) 1) Check if Batt Low LED is ON, indicating low battery if so change batteries 2) Wi Tx Edge 1 (or 2) is too far away. Move or reposition Wi Tx Edge 1 (or 2) "RANGE OK" LED is OFF intermittently for Edge 1 (or 2) Tx or Rx PAIR LED Blinking indicate pairing mode 1) Choose different RF channel for Wi Edge Rx and Tx Edge 1 or 2 (see p 7) 2) Lower RF power on Wi Edge Rx and Tx Edge 1 or 2 (see p 8) 13 MAX WIRELESS EDGE 900 NOTES MAX WIRELESS EDGE 900 14 QUICK INSTALLATION GUIDE MAX WIRELESS EDGE 900 RESIDENTIAL / COMMERCIAL / INDUSTRIAL APPLICATION Max Wi Tx Edge 1 Max-WETX 10K Opening Edge (Sold Separately) Max Wi Edge Receiver Max-WERX Max Wi Tx Edge 2 Max-WETX 10K Closing Edge (Sold Separately) MAX Wi Edge Kit Works exclusively with Max Gate Operators Maximum Controls LLC · 949.699.0220 10530 Lawson River Ave. Fountain Valley CA 92708 · www.MAX.US.com