Ryobi Electric Pressure Washer Water Broom

Introduction

This operator's manual provides essential information for the safe and effective use of the Ryobi 11-inch Water Broom accessory with your electric pressure washer. Please read and understand the entire manual before operating the accessory. Always refer to your pressure washer's operator's manual for specific operating instructions.

Safety Warnings

WARNING: To reduce the risk of injury, always read and understand the operator's manual for your pressure washer before using this accessory. Ensure all accessories are properly connected before starting any cleaning project. Always wear eye protection with side shields compliant with ANSI Z87.1. Never point the spray stream at people, pets, electrical devices, or the unit itself. Turn off the pressure washer before changing or adjusting accessories. This accessory is for cold water use only.

Risk of Injection: Do not point the spray stream at people, pets, or electrical devices. Never place any body part in the stream. Leaking hoses and fittings can also cause injection injury. Do not hold hoses or fittings.

Kickback: To reduce the risk of injury from kickback, hold the spray wand securely with both hands when the machine is on.

WARNING: Never lift the water broom while operating the pressure washer. Do not depress the trigger until the water broom nozzles are completely underneath the surface being cleaned, and always release the trigger before removing the water broom from underneath the surface.

Product Specifications

• Connections: 1/4 in. Quick Connect Plug
• Broom Width: 11 in.
• Maximum Pressure: 3,300 psi
• Maximum Water Flow: 3.0 gpm
• Maximum Water Temperature: 140°F

Installation of the Water Broom on the Spray Wand

Refer to Figure 1. Insert the water broom inlet plug (A) into the spray wand quick connect coupler (B) and secure it.

Using the Water Broom

Refer to Figures 2-4.

• Connect the hose to the pressure washer as described in your pressure washer manual.
• Start the pressure washer as described in your pressure washer manual.
• Pull out the pivot knob (A, Fig. 2) and move the pivot coupler (B, Fig. 2) back or forward to achieve the desired nozzle orientation.
• For cleaning large flat surfaces (sidewalks, driveways): Use with nozzles pointed down and forward (pivot coupler in back position, Fig. 3). Walk slowly behind the water broom, cleaning as you go.
• For cleaning undersides of elevated items (e.g., car undercarriage): Pivot so nozzles point upward (pivot coupler in forward position, Fig. 4). Ensure nozzles are completely underneath the surface before engaging the trigger.

Nozzle Maintenance

Refer to Figure 5.

The nozzles (B, Fig. 5) are pre-assembled and suitable for pressure washers operating at 2300 to 3300 psi with a maximum flow rate of 3.0 gpm. Clogged or dirty nozzles can cause excessive pump pressure.

• Turn off the pressure washer and water supply. With the water broom on the ground, pull the trigger to release water pressure.
• Disconnect the water broom from the spray wand.
• Use a straightened paper clip (A, Fig. 5) or fine needle to clear any foreign material clogging the nozzles (B, Fig. 5).
• Remove the high-pressure filter (see next section) and flush debris from the nozzles using a garden hose, allowing water to drain through the inlet plug.
• Reinstall the high-pressure filter and reconnect the water broom.
• Turn on the water supply and start the pressure washer.

Changing the High Pressure Filter

Refer to Figure 6.

• Disconnect the water broom from the spray wand.
• Place a flat head screwdriver in the slot of the inlet plug (A, Fig. 6) and turn counterclockwise to remove the filter (B, Fig. 6).
• Replace the old filter with a new one (not included).
• Using a flat head screwdriver, turn the new filter clockwise until it is no longer visible over the top of the inlet plug.
• Reconnect the water broom to the spray wand.

Replacement Parts

The following replacement parts can be ordered by calling the customer service department at 1-800-860-4050:

• High Pressure Filter (Part No. 308103010)
• 3/4 in. Retaining Ring (2) (Part No. 694723003)
• O-Ring (4.5 mm ID x 1.8 mm CS) (Part No. 570742132)

Contact Information

TECHTRONIC INDUSTRIES POWER EQUIPMENT
P.O. Box 1288, Anderson, SC 29622 USA
1-800-860-4050
www.ryobitools.com