Instruction Manual for bouncepad models including: BP-COR-S6, Core Swivel 60 Tablet Stand, Core Swivel 60, Tablet Stand, Stand
Core Swivel 60 Tablet Stand Assembly Guide
Core Swivel 60 Tablet Stand
Core Swivel 60 Assembly Instructions Tools Required: Pencil Electric Drill 7mm Spanner *or adjustable spanner 5.0mm Drillbit *if fixing from below 2.5mm Drillbit *if fixing from above 16mm Holesaw *if routing the tablet cable through your mounting surface Socket Driver Sheet Code: BP-IM-090_REV0 Release Date: 15/08/2024 Copyright 2024 Spotspot Ltd. (T/A Bouncepad) all rights reserved. Confidential, no part of this publication may be reproduced or transmitted in any form without the written permission of the copyright holder. Flat Cable Fixings Kit Tablet Mount Plate Shell Static60 Mounting Arm Rotate In the Box Follow steps A A if "Fixing from above". Minimum Mounting surface thickness : Metric Imperial 34mm 1 5/16" Tighten screw(s) using hand tools, using electric tools may damage your Bouncepad. 90° limit screw position Limit Screw Slotted Driverbit 4x No.8 Countersunk Self tapping Screw 4x M4 Wing Nut 2x 3mm x 6mm Pan Head Screws 4x M4 Split Washer 4x M4x40mm Socketset screw 1x Slotted Driver Bit 8x M4x16mm Buttonhead screw 1x T20 Pin Torx Driver Bit 1x Cable Clamp 4x M3x10mm Countersunk Screw 4x M4 Washer 1x Case Washer 2x Limit screw 1x T10 Pin Torx Allen Key Maximum Mounting surface thickness : Metric 25 1x Cleaningmm 4x M4 Wipe Locking Nut Imperial 1" Fixings List * Due to the modular nature of our product range you may receive additional fixings in the fixings kit Tighten screw(s) using hand tools, using electric tools may damage your Bouncepad. T20 Pin Torx Driverbit M4x16mm Buttonhead screw 90° limit screw position Maximum Mounting surface thickness : Metric Imperial 25mm 1" Follow steps B B if "Fixing from below". 180° limit screw position 180° limit screw position Configure the rotation range - both 1 arrows must point in the same direction. Default configuration is 270°. Insert 2x limit screws. Attach the Static60 Arm. 2 The Static60 Arm must lean forward in the same direction as the two arrows. Using the hole template 3 (see step A or B), mark the hole positions specific to your chosen fixing method. A B B 46.0mm A C A Front A Ø65.5mm Mark `A' positions for "Fixing from above" A1 (Ø2.5mm drillbit). Mark `C' for the cable hole. (Ø20.0mm Holesaw). C Front B B Mark `B' positions for "Fixing from below" B1 (Ø5.0mm drillbit). Mark `C' for routing the cable hole. (Ø20.0mm Holesaw). Drill the 4 required holes. 48.0mm Tighten screw(s) using hand tools, using electric tools may damage your Bouncepad. T20 Pin Torx Driverbit No.8 Countersunk, self tapping Screw M4x40mm Socketset screw M4 Washer M4 Locking nut Tighten screw(s) using hand tools, using electric tools may damage your Bouncepad. M4 Washer M4 Wing nut Lift & hold the A2 rubber screw covers. Secure the Rotate to A3 the mounting surface, then close the covers. A4 Go to step 5 Screw in the 4x Socket B2 Set Screws. Ensure full thread engagment. Secure to the surface. B3 Locking nuts offer greater security. Tighten screw(s) using hand tools, using electric tools may damage your Bouncepad. B4 Go to step 5. T20 Pin Torx Driver Bit M4x16mm Buttonhead screw M4 Split Washer Case Washer Locate & attach the Shell 5 to the Static60 in the correct orientation. *Before attaching the Mounting Plate, fully clean the back of the tablet with the provided wipe and allow it to fully dry. FoLraonpdtismcaalpaedhteasbiolne,tporerisesnfitramtliyoannd leave for 72hrs in a 20°C environment before use. Do not reposition. Do not use prior to the 72hrs. Portrait tablet orientation Landscape Portrait Remove the Mounting Plate adhesive 6 backing. Attach level & centrally to the Tablet back as shown. Attach the Flat Cable 7 to the Tablet with the U-Bend Head. 2x 3mmx6mm Pan Head Screws Cable Clamp Top Fixing Cover T10 Pin Torx Allen Key T10 Pin Torx Allen Key Secure the Flat Cable 8 to the Mounting Plate with the Cable Clamp as shown. Remove the Fixing Covers. Feed 9 the Flat Cable into the assembly & locate the Tablet in the chosen orientation. 4x M3x10mm Countersunk Screw Bottom Fixing Cover Secure the Tablet to the 10 Shell & attach the Fixing Covers as shown. Connect tablet 11 to power & installation is now complete.PDFium PDFium