Holystone HS600 Drone User Manual

Model: HS600

Version: 2.0

Important Safety Information

WARNING: Only intended for ages 16+

Contact: +1 (833) 766-4733 | www.holystone.com

Support: usa@holystone.com (USA), eu@holystone.com (EU), ca@holystone.com (CA), au@holystone.com (AU)

Reading Guidance

Icon Key:

⚠️: Essential precautions.
?: Tips for operation and usage.

This product offers tutorial videos and user guides. For a smooth start, watch tutorial videos and review the "Disclaimer and Safety Guidelines" and "Quick Start Guide". For a comprehensive understanding, refer to the "User Manual".

Scan QR code [QR code placeholder] to view tutorial videos.

1. Product Introduction

Drone Diagram

The drone features:

Propellers (A and B)
Gimbal and Camera
Camera Cover
TF Card Slot
Optical Flow Indicator
Optical Flow Lens

Transmitter Diagram

The transmitter includes:

Cellphone Holder
Joysticks (Left and Right)
LCD Screen
Control buttons: Takeoff/Landing, Emergency Stop, Speed Switch, Cruise Control, Take Photo, Record Video, Return to Home, GPS Switch, Zoom Dial, Gimbal Dial.
Power Switch
Charging Port (Type-C)
Connection Port
Cellphone Slot
Storage Slots for Joysticks

Transmitter LCD Screen Information

The LCD screen displays:

Transmitter WiFi Signal
Transmitter Battery Level
GPS Signal Strength
Transmitter Signal Strength
Camera Status
Flight Speed
Drone Status
Drone Battery Level
Flight Distance
Flight Height
Horizontal Speed
Vertical Speed

Unit Switching: Press and hold the button while simultaneously pressing the power button twice to toggle between "m" and "ft".

Low Transmitter Battery: Recharge the transmitter when its battery icon is low.

2. Operation Guidance

Charging

Drone Battery: Use the provided Type-C charging cable with a 5V/3A USB adapter or power bank. Charging takes about 2 hours. Battery level indicators show charging status.

Transmitter: Use the provided Type-C charging cable. Charging takes about 2 hours, providing approximately 2.5 hours of usage.

Note: Read "Battery Safety" before charging. Allow battery to cool before charging. Do not turn on the transmitter while charging.

Pre-Flight Preparations

Mount joysticks onto the transmitter.
Unfold the front landing gears.
Remove the camera cover (gently pull forward). Protect the gimbal when not in use.
Install propellers (A/B) by aligning with the motor shaft, pressing down, and rotating to lock/unlock. Ensure correct propeller placement.
Insert the drone battery securely into the compartment, ensuring buckles click. Remove only when powered off.
Insert a TF card (Class 10 or above, up to 128GB) before inserting the battery for photo/video storage.

Flight

Pre-Flight Checklist

Ensure transmitter, cellphone, and drone battery are fully charged.
Ensure drone battery and propellers are installed securely.
Ensure drone arms are fully expanded.
Ensure motors are clear of obstructions.
Ensure the camera cover is removed.
Use only company-provided accessories.

Takeoff Procedure

Environment: Operate outdoors in an open area.

Turn on Drone: Press and hold the Power Switch for 3 seconds. Place on a level surface, head forward. Drone status indicator blinks red, waiting to pair.
Turn on Transmitter: Short press the power switch, then hold for 3 seconds.
Auto-Pairing: Takes about 40 seconds. Transmitter beeps, then long beeps once when pairing is complete. Transmitter signal strength on LCD is full.
Cellphone Connection: Pull out the phone holder. Connect the appropriate cable (Type-C, Micro-USB, Lightning) between the transmitter and your cellphone. For Android, select "charge only".
Run App: Launch the "HS FLY" app and open the live-feed interface.

Compass Calibration

Note: Perform calibration approximately 3 ft above the ground.

Push both joysticks towards the inner, upper corners simultaneously.
Rotate the drone horizontally until the transmitter beeps once.
Point the drone head upward and rotate until the transmitter beeps again. Calibration is complete.

Caution: Do not calibrate near magnetic interference (e.g., parking structures, steel structures, cars). Do not carry ferromagnetic objects (like mobile phones) near the drone during calibration.

GPS Mode

Note: Do not use indoors.

The drone searches for GPS signals. The front indicator turns solid white, rear solid blue when signals are acquired. GPS signal strength on the LCD will be full. Blinking lights indicate searching.

If GPS is weak or unavailable, press the Return to Home button for 2 seconds to exit GPS mode and enter Attitude Mode ("ATT"). In ATT mode, GPS functions are unavailable.

Takeoff and Landing

Unlock Motors: Push both joysticks simultaneously toward the inner, lower corners. Motors start spinning. Motors auto-lock after 20 seconds of inactivity or can be manually locked by pushing joysticks to inner corners.

Takeoff: Short press the takeoff/landing button. The drone ascends slowly. Control with joysticks.

Landing: While airborne, short press the takeoff/landing button. The drone descends slowly.

Orientation: Periodically adjust transmitter/drone orientation for optimal communication range.

3. Product Functions

Drone Functions

Cruise Control: Long press the speed switch button to activate. The drone flies straight at its current speed. Long press again to exit.
Gimbal Control: The 2-axis gimbal stabilizes the camera. Tilt range is -80° to 0°. Use the Gimbal Dial to adjust the camera tilt.
Zoom: Use the Zoom Dial. Scroll right to zoom in, left to zoom out.
Emergency Stop: Long press the button for 2 seconds. Works only when the drone's altitude is below 16ft. Use only in emergencies.
Speed Switch: Short press the button to cycle through speeds: Low (1 beep), Middle (2 beeps), High (3 beeps).
Take Photo: Short press the button. The photo icon on the LCD blinks.
Record Video: Short press the button. The video icon on the LCD blinks. Short press again to stop. The "Take Photo" function is disabled during recording.
Return to Home (RTH): Brings the drone back to the recorded Home Point. Requires GPS mode.
- Smart RTH: Short press the RTH button. Transmitter beeps. Short press again to exit.
- Failsafe RTH: Activates automatically if GPS is strong, Home Point is recorded, transmitter connection is lost, and compass has no interference. Drone returns automatically. Can be manually ended if connection is re-established.
- RTH Altitude: If drone altitude is higher than or equal to the set Return Altitude (RA), it flies over the Home Point then descends. If lower than RA, it ascends to RA, flies over Home Point, then descends.
- Low Voltage RTH:
  - First Stage: Drone returns to Home Point, transmitter beeps continuously, LCD displays "LOW VOLTAGE." Drone is restricted to a limited area around the Home Point.
  - Second Stage: Drone returns directly to Home Point and lands automatically.
Note: Drone cannot avoid obstacles during RTH. RTH requires a stable GPS signal.

3. Product Functions (Continued)

APP Functions (HS FLY)

Homepage: Return to main menu.
System Status: View flight status and warnings.
Interference Index of Compass: Monitor electromagnetic interference.
Transmitter/Drone Battery Level: Real-time display.
GPS Signal: Display GPS signal strength.
Settings: Adjust flight height/distance, return altitude, PTZ parameters, etc.
Takeoff/Landing: Initiate takeoff or landing via the app.
Return to Home: Activate RTH from the app.
Image Follow: The camera tracks a selected target, maintaining its position.
GPS Follow: The drone follows the GPS coordinates of your mobile phone. Use in open areas; drone has no obstacle avoidance.
VR Screen-Split: View 3D live feed with VR glasses.
Point of Interest (POI): Drone circles a designated point at a set radius.
Catapult: Drone flies backward and ascends while recording, keeping the camera on the subject.
One-key Ascension: Drone ascends while recording, keeping the camera on the subject.
Gesture Selfie: Trigger the camera shutter using a "V" sign or palm gesture.
TapFly: Draw a flight path on the screen for the drone to follow.
Camera Filters: Apply visual filters.
Spiral Up: Drone ascends and spirals around a subject while recording.
Portrait Mode: Switches camera orientation to portrait.
Camera Settings: Configure camera parameters.
Shooting Modes: Time-lapse, Slow Motion, Panorama.
Take Photo/Record Video: Initiate photo capture or video recording.
Album: Preview captured media.
Voice Recording: Record audio via the mobile phone.
Map View: Switch between camera feed and map display.
Flight Parameters: View distance, altitude, speeds.

Flight Settings on APP

Beginner Mode: Default mode with limited flight height and distance. Return altitude during RTH is 65ft.

Users can adjust parameters like flight height, distance, and return altitude in the Settings menu.

4. Appendix

Specifications

Drone

Model: HS600
Weight: 603g / 21.3oz
Max Wind Speed Resistance: 7.9m/s
Max Takeoff Altitude: 9842ft / 3000m
Operating Temperature Range: 32°F to 104°F (0°C to 40°C)
Size (folded): 202*95*83 mm
Size (unfolded): 375*258*83 mm
Max Flight Height: 394ft / 120m

Drone Battery

Capacity: 3500mAh
Battery Type: Lithium-ion Polymer Battery
Charging Temperature Range: 41°F to 104°F
Voltage: 11.1V
Rated Power: 38.85Wh
Charging Time: Approx. 2 hours

USB Charging Cable

Input: 5V/3A

Troubleshooting

Issue	Possible Causes	Suggested Solutions
Gimbal protection activated / Gimbal cannot be adjusted	Gimbal cover not removed; Drone not level; In compass calibration mode; Drone on uneven surfaces.	Remove cover; Place drone levelly; Wait for self-check; Use landing pad or even surface; Ensure space below gimbal.
Compass interference / Abnormal posture	Compass interference; Abnormal posture.	Recalibrate compass; Operate in open areas away from interference sources (buildings, power lines, signal towers).
Video lag or limited transmission range	Propeller deformation/damage; Interference with video signal; Transmitter/device not oriented towards drone; Overly rapid joystick movements; Phone performance issues.	Replace propellers; Operate in open areas; Orient devices towards drone; Adjust joystick movements smoothly; Close background apps.

5. Compliance Information

FCC Notice: This device complies with part 15 of the FCC Rules. Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Supplier's Declaration of Conformity is available at: https://www.holystone.com/Download/US/HS600_FCC_sDoC.pdf

This equipment complies with FCC Rules for Class B digital devices, designed to provide reasonable protection against harmful interference in residential installations. If interference occurs, users are encouraged to correct it by reorienting antennas, increasing separation, connecting to a different circuit, or consulting a dealer/technician.

Unauthorized modifications may void the user's authority to operate the equipment.