1. Summary
The PXN-9607X is a Bluetooth controller with vibration, specifically designed for the Nintendo SWITCH platform. It is also compatible with PC and Android platforms.
2. Functional Characteristics
- Bluetooth 5.0 connectivity.
- Compatible with Nintendo SWITCH host platform and PC platform.
- Features a low power mode (disconnects after sleep).
- Supports sensor induction function on the SWITCH host platform.
- Equipped with a double motor vibration function.
- Offers a linear transmission distance of over 10 meters.
- Built-in 3.7V lithium battery, providing over 20 hours of use.
- Rechargeable via TYPE-C USB.
3. Product Diagram
The diagram illustrates a wireless game controller. It features a D-pad, four face buttons labeled A, B, X, Y, two analog sticks, shoulder buttons (ZL, ZR, L, R), and other function buttons.
4. Instructions
4.1 Initial Setup
The first step is to enable wired communication settings on the host device. This is shown in the following system settings screenshot:
Screenshot Description: The image displays the Nintendo Switch system settings menu. Key options visible include 'System Settings', 'Controllers and Sensors', and 'Controller Vibration' which is set to 'ON'. 'Pro Controller Wired Communication' is also enabled ('ON'). This setting allows the controller to communicate via wired connection when plugged in using the USB charging cable, disabling the NFC function.
4.2 Power ON/OFF
- POWER ON: Press and hold the "HOME" button for 3 seconds to activate the controller. The four LEDs will flash once per second.
- POWER OFF: Press and hold the "HOME" button for 1 second to close the controller.
4.3 Connection
- SWITCH Host: Press and hold the "Y" button, then press the "HOME" button to initiate pairing. The four LEDs will flash rapidly. Upon successful connection (indicated by a solid LED), the LEDs will light up. LED1 indicates the first connected device, LED2 the second, and so on.
- Android Platform: Press the "A" button, then press the "HOME" button again. LEDs 2 and 3 will flash quickly and then light up solid upon successful connection.
- PC Connection: Connect the gamepad to the computer using the USB Micro data cable. It will function as an x-input key value gamepad.
4.4 Low Power Prompt
- The current connection light flashes twice per second when low power is detected.
- Shutdown voltage is 3.2V.
4.5 Charging Tips
- Charging while connected: The charging indicator light will flash slowly for 1 second and then light up normally when fully charged.
- Disconnect charging: Insert the charging cable. Four LED lights will flash once every 1 second. The four LED lights will turn off when charging is complete.
4.6 Controller Sleep Function
- Press the "HOME" button to wake the controller from its reconnect state. If no signal is received for 10 seconds, it will enter sleep mode.
- After connecting the controller, it will automatically enter sleep mode if there is no keystroke or axis movement for 5 minutes.
4.7 Calibration of the Controller
When the controller is off, press and hold the "-" button, "B" button, and "HOME" button simultaneously. The four LEDs will illuminate alternately in two groups. Place the controller on a horizontal surface, then press the "+" button to complete calibration.
5. Other Parameters
| NO. | Button | SWITCH Code | PC X-INPUT Code | Android Code |
|---|---|---|---|---|
| 1 | A | A | B | 97 |
| 2 | B | B | A | 96 |
| 3 | X | X | Y | 100 |
| 4 | Y | Y | X | 99 |
| 5 | L | L | LB | 102 |
| 6 | R | R | RB | 103 |
| 7 | - | - | BACK | 109 |
| 8 | + | + | START | 108 |
| 9 | 0 | screenshots | NO | NO |
| 10 | 3D press L | 3D press L | Thumb L | 106 |
| 11 | 3D press R | 3D press R | Thumb R | 107 |
| 12 | ZL | ZL | LT | 104 |
| 13 | ZR | ZR | RT | 105 |
| 14 | ML-> X (3D VR) | ML-> X (3D VR) | ML->X (3D VR) | ML-> X (3D VR) |
| 15 | ML-> Y (3D VR) | ML-> Y (3D VR) | ML->Y (3D VR) | ML-> Y (3D VR) |
| 16 | MR->X (3D VR) | MR->X (3D VR) | MR->X (3D VR) | MR- >X (3D VR) |
| 17 | MR ->Y (3D VR) | MR ->Y (3D VR) | MR ->Y (3D VR) | MR->Y (3D VR) |
| 18 | D-PAD-UP | D-PAD- UP | D-PAD- UP | 19 |
| 19 | D-PAD-DOWN | D-PAD- DOWN | D-PAD- DOWN | 20 |
| 20 | D-PAD-LEFT | D-PAD- LEFT | D-PAD- LEFT | 21 |
| 21 | D-PAD-RIGHT | D-PAD- RIGHT | D-PAD- RIGHT | 22 |
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
