One moment, please...One moment, please...
User Guide for WIRELESS PACIFIC models including: Elite Plus, Pro Plus, X10DR Elite Plus and Pro Plus Models, X10DR, Elite Plus and Pro Plus Models, Pro Plus Models, Plus Models
To put Gateway into programming mode: Turn off gateway. Then hold gateway ON/OFF button down while attaching the programming cable to device micro-USB port and ...
File Info : application/pdf, 13 Pages, 4.05MB
DocumentDocumentOut of Vehicle Communications Solution Programming Parameter Guide For Elite Plus and Pro Plus Models Some features are only applicable to firmware version 5.0 or later Rev 1 How to install Programmer: Runs On PC or Mac running Windows 10/11 NOTE: Requires USB 2 Port. The programmer will not work with USB 3 - if your PC only has USB3 ports suggest you attach X10DR device via a usb patch block most are USB 2.) Included with the Programmer download file application are instructions on how to set-up the programmer on your Windows 10/11 PC. Please follow those instructions to install the programmer correctly onto your computer. www.x10dr.com How to use Programmer: Runs On PC running Windows 10/11 Requires USB 2 Port. To put Handset into programming mode: Turn off Handset, attach programming cable between device hirose port and PC then press the Handset's Red right side button while holding PTT. The Handset's LED will light red. To put Gateway into programming mode: Turn off gateway. Then hold gateway ON/OFF button down while attaching the programming cable to device micro-USB port and PC USB port. The Gateway's LED will light red. Note: The gateway's RJ45 socket should not be connected to the host radio. Always READ device before proceeding further. We suggest you SAVE the file onto your PC for re-loading if required. A GREYED out feature means your device does support that capability. Read Device Press to load current programming parameters from device to screen. Program Device Press to load current screen programming parameters to a device. Restart (important) Press to restart programmed device before removing programming cable. Lock - Unlock File Press to lock your desired parameter configuration before undertaking batch fleet programming. This will prevent you errantly changing a parameter unknowingly during reprogramming. Load File Press to load a previously saved programming parameters to device from its saved PC location. Save File Press to save a programming parameters from screen to desired PC location saved location. Defaults Press to reset with default device parameters Exit Press to exit program. Handset Parameters Radio PTT key beep Sounds talk permit two tone sequence whenever PTT is pressed and Handset is within range of its gateway. Default - OFF Emergency key beep Sounds single tone whenever Emergency button is pressed and Handset is within range of its gateway. Default - ON Talkaround PTT key beep Sounds talkaround triple tone sequence whenever Talkaround button is pressed and Handset is within range of its gateway. Default - ON Stealth mode always active Disables all alert tones and LED status light. User can manually enable stealth mode if programmed off. Default - OFF Mute speaker on PTT Disables all speaker audio whenever PTT is pressed. Default - OFF Mute speaker on charge Disables speaker when Handset is in gateway or a charger. Default - ON LED charge indicate Disables "momentary blink" charge indicate when Handset is placed into gateway or a charger and device is charging. Default - ON Auto turn on when charging Causes Handset to automatically turn on whenever it is placed in gateway or a charger. Default - ON Minimum volume is off Allows user to turn the speaker audio off instead of level 1. Default - OFF Mandown Monitor* Enables/disables Mandown function via programmer Default - OFF Internal Mic Only Operation Maintains operation via internal microphone when accessory attached to Hirose port required for when WPEH-X10/WPTEP-X10 earpieces connect via Hirose headset port rather than the 3.5 audio jack. Default - OFF * (when fitted) Out of range turn off time Sets time in hours that a Handset that is not actively connected to a gateway will remain powered on before turning itself off. Default - 8 hours Handset Programming: Basic functions Low battery beep voltage Sets the remaining battery voltage that will cause the low battery alert tones to be generated. (for longer shift life you may set voltage lower but you may get less warning before device automatically shuts off. Default - 3.5V Low battery beep interval timer Sets the interval that the low battery alert tones are sounded in the Handset. Default - 5 minutes Handsfree Function Enables user selectable handsfree intercom function in Plus Handsets. Default - ON Toggle PTT/TA Button Assignment Configures Handset so that pressing the side Grey button toggles the side PTT button assignment between host radio PTT and Talkaround or 2nd Radio device(Legacy Mode) PTT /PA Mode when used with XSJB or similar. Default - OFF Top 1 Top 2 Microphone PTT Left 1 Left 2 Status light Automatic Relay Mode / Command Relay Mode Selects the Relay Mode type in Plus Handsets. Default - Command Relay ON Right 1 Charging Contacts Hirose audio jack 3.5mm earpiece audio jack We recommend you use the XGALA Gateway Audio Level Adjustment software tool for setting levels between host radio and X10DR gateway. It can be downloaded at https://www.x10dr.com/supports for setting audio in and out between the gateway and the host mobile radio. The following Handset adjustments are designed to cater for different audio accessories and/or user applications requiring alternate audio sensitivities to suit different operating conditions. Internal Mic Gain Sets the internal microphone's transmit audio level sensitivity. Default - 3 Internal Mic High Gain Boost Sets the internal microphone's sensitivity when "Live Mic" is active. Default - 6 External Mic Gain Sets the external microphone's transmit audio level sensitivity. Default - 6 External Mic High Gain Boost Sets the external microphone's sensitivity when the X10DR's "Live Mic" is active or when user manually selects high gain by powering up microphone with blue volume up button pressed. Default - 6 Remote PTT Gain Boost Increases sensitivity of internal microphone when remote/handlebar PTT is pressed. Default - 9 Fixed Alert Tone Volume Limits all user monitored alert tones to level set below rather than being controlled by Handset volume controls . Default - OFF Handset Programming: Audio Levels 3 Alert Tone Volume Sets the value of the "Fixed Alert Tone" when enabled that a user will hear from their Handset. Default - 5 When Handset is configured for press & hold Emergency Audio link active time Sets the duration the transmit audio is active after Emergency button is released. Feature is intended for those mobiles that activate their own internal "Live Mic" functionality whenever emergency is triggered. This allows the Handset's Tx audio to be broadcast over the radio's transmit channel, (Note: This assumes mobile sources "Live Mic audio" from its external mic input). Default - 0 When Handset is configured for short/long press Advanced Emergency Transmit Time Sets the time duration that X10DR's internal "Live Mic" functionality Tx audio is active when Emergency activated. Default - 0 Receive Time Sets the time duration that X10DR's internal "Live Mic" function enables radio receive audio to be heard by the user, before transmitting further "Live Mic" audio over the host mobile radio when Emergency repeat cycles is greater than zero. Default - 0 Emergency repeat cycles Sets the number of "Live Mic", Tx and Rx cycles when Advanced Emergency is triggered. Default - 1 Transmit audible emergency tone Causes an audible emergency warble tone to be transmitted over the host mobile radio channel when emergency is activated. Default - Off Handset Programming: Emergency Hirose Pin 2 function Sets Hirose pin 2 to be either BAT+ (~3.3VDC) to power external accessories or bridged output speaker audio when pin 2 is set for speaker negative. Default - Speaker -VE Acc PTT Sets whether Hirose PTT input generates Talkaround or Radio PTT. Default - Radio PTT PTT Sets function of main large PTT button. Choose from drop down box. Default - Radio PTT Top 1 Sets function of top left Orange button. Choose from drop down box. Default - Emergency Top 2 Sets function of top right Grey button. Choose from drop down box. Default - Talkaround PTT Left 1 Sets function of top left button. Default - SP: Volume up / LP: Relay mode ON/OFF Left 2 Sets function of bottom left button. Default - SP: Volume down Right 1 Sets the function of right side button. Re-assigning requires hardware modifications. Default - LP: OFF/ON Long Press Duration Sets time button must be pressed to action a Long Press. Default - 5000mSec 5 Handset Programming: Hardware 5 Handset Programming: Dropdown box button assignment selection Plus Handset Right 1 Button - Short Press Assignments: Search - Resets connection to its paired gateway, other paired gateways or Relay Mode paired Handsets. LTE RSM - Special Application Aux 1 (or 2) - Special function when used with XFSB/ XSJB Smart boxes. Relay Mode On/Off - Toggles Relay Mode ON / OFF to allow Handsets to talk directly or mesh back to vehicle when one Handset is out of vehicle gateway range Default - Toggle Radio/ TA PTT Toggle Radio PTT - Toggles Side PTT button between Network or Local transmit (Talkaround) Dual Radio - Toggles top Yellow button between Radio One and Radio two ( requires use of XSJB/ XFSB) Plus Handset Top 1/2, Left 1/2 Button - Short Press Assignments: Search - Resets connection to its paired gateway, other paired gateways or Relay Mode paired Handsets. Volume Up - Increases Handset speaker audio volume in 7 steps. Volume Down - Decreases Handset speaker audio volume in 7 steps. Aux 1 (or 2) - Special function when used with XFSB/ XSJB Smart boxes. Emergency - Triggers Emergency on host mobile/wireless network device where available. HF On/Off - Toggles Handsfree local full duplex intercom operation ON / OFF. Relay Mode On/Off - Toggles Relay Mode ON / OFF to allow Handsets to talk directly or mesh back to vehicle when one Handset is out of vehicle gateway range. Toggle Radio PTT - Toggles Side PTT button between Network (Radio) or Local transmit (Talkaround) Mandown Alert- used with XMD mandown option for user audible alerts Dual Radio - Toggles top Yellow button between Radio One and Radio Two ( requires use of XSJB/ XFSB) Plus Handset Right 1 Button - Long Press Assignments: On/Off - Manually powers Off and On the Handset. Power On - Manually powers ON a Handset that is OFF. When so assigned we suggest that the blue Volume Down button (L2) be programmed for Long Press: Power OFF for intuitive operation (other buttons can be chosen if desired). This assignment is suggested when short press is assigned other than to its default setting. Plus Handset Top 1/2, Left 1/2 Button - Long Press Assignments: as per above short press selection but with following addition assignable function: Power Off - Manually powers OFF a Handset that is ON. (Default button assignment : Volume down (L2) button) Default Plus Assignments Right 1 SP: Search / LP Power On/Off Top 1 Emergency Top 2 Talkaround PTT Left 1 SP Volume Up / LP Relay Mode On/Off Left 2 SP Volume Down Right 1 Top 1 Top 2 Left 1 Left 2 Pro Plus Gateway Parameters Elite Plus XRTG Elite Plus Status light Function Button - Manual Off/On - Touchless Pairing - Master Reset - Find Me Hold while powering up for programming (LED glows solid RED) Status light *We highly recommend use of the XGALA Gateway Audio Level Adjustment tool for setting audio levels. Download here: https://www.x10dr.com/supports Programming XRTG As the XRTG is externally mounted, the Function Button and related LED indicator are internally enclosed but readily accessible when you remove the front cover. Use the button and LED the same as standard or XIVG function button. Pairing a XRTG or XIVG Gateway Use the Auto pairing method where you power up the gateway with its host radio turned off. For the next 30 seconds the gateway will be in pairing mode. Powering on the radio will in most cases abort the process. XIVG Gateway Elite Plus and Pro Plus models available Function Button - Manual Off/On - Erase Pairing - Find Me- Hold while powering up for programming (LED glows solid RED) Receiver Input Gain From Radio Sets the receive input sensitivity. Default - 0 Transmit Output Gain To Radio Sets the audio output level to radio when local/remote /handlebar PTT is pressed or when "Live Mic" is active. Default - 0 Talk Around Output Gain to other X10DRs Sets the "intercom" microphone audio level. Default - 0 Find MeTM Function Enables Find Me function in gateway. User double presses gateway Function button to trigger Find Me alert tones or triggers Remote FindMe. Default - OFF Radio Receive VOX/COR Enables VOX derived COR. Default - ON VOX Trigger Level Sets the gateway's audio detect sensitivity for VOX derived COR. Default - 70 Public Address Mode Sets the gateway so only Handset Talkaround audio is sent to the gateway 3.5mm jack. When unchecked both Radio PTT and Talkaround audio is available for in-car monitor use. Default - OFF Monitor Emergency Input Alert Tone Causes Emergency warble alert tone to sound in all cross connected X10DR Handsets whenever emergency input is triggered. (i.e. triggered from another gateway or externally supplied ground input). Default - OFF Trunking Support Enables speaker audio upon PTT for 500mS, so host trunked mobile's Channel Grant /Talk Permit tones can be clearly distinguished by user. Handset Mic audio is also muted for 500mS to prevent those tones being rebroadcast over talkgroup. For optimum performance set VOX trigger level for 90-100 for fastest response. Default - OFF Gateway Programming: Audio Levels XSJB/XFSB Dual Radio Support Enables Dual Radio with Talkaround functionality when used with XSJB/ XFSB accessories Default - OFF Multi Operational Mics Allows two or three Elite Series Mics to be simultaneously operational through the one Elite gateway unit. Default - ON Remote Find MeTM Enables Find Me function in gateway via grounding the white wire connected to pin 8 (Replaces Remote PTT function) Default - OFF I/O Defines whether the specific gateway interface pin is assigned as an input or an output. Active Sets whether the interface pin needs to be held low or pulled up high to activate assigned functionality. Function Assigns desired functionality to Interface pin. Choose the desired input or output from the dropdown boxes. Pulse Defines the length of time an input must be activated before the function is triggered or alternatively how long an output is activated when the assigned function has been triggered. A value of zero means an input triggers instantly. Gateway Programming: Hardware Pro Plus Default settings: Handset - Gateway All rights reserved Wireless Corporation Limited ©2024 Wireless PacificTM, X10DR®, Liberate your mobileTM, Find MeTM, Powerfully SimpleTM and their logos are trademarks or registered trademarks of Wireless Corporation Limited : Manual revision 1