NM3015 AX3000 Dual Band WiFi 6 Mesh Router

Package Content

• NM3015 x 1
• Power Adapter x 1
• Ethernet Cable x 1
• Quick Installation Guide x 1

Ports and Indicators

AX3000 Dual Band WiFi 6 Mesh Router

Ports:

• 12V= (Power Input)
• WAN
• LAN1
• LAN2
• LAN3
• WPS
• RESET

Indicators:

• Power: Indicates the router's power status.
• Wi-Fi: Indicates Wi-Fi status.
• WPS/Mesh: Indicates WPS and Mesh networking status.

1. Connecting the Master Mesh Router

1. Take the router out of the box. Connect one end of the network cable to the Modem or broadband network port, and the other end to the WAN port of the router.
2. Use the included power adapter to connect the NM3015 to a power socket. Wait for approximately 60 seconds. The system will finish the startup process, and the Wi-Fi LED indicator will light up blue.
3. Connect your wireless or wired device to the mesh router.
   • Wireless: Find your SSID and wireless password on the device label.
   • Wired: Use an Ethernet cable to connect a LAN port of the mesh router to your computer.

Diagram Description: A diagram shows the router connected to a modem via a WAN port, and a computer connected via a LAN port. The power adapter is shown connecting to the router and a power outlet.

2. Add a Slave Mesh Router

1. Power on a new mesh router. Place it within the wireless coverage of another mesh router. The optimal distance is no more than 20 meters. Consider the following suggestions:
   • Do not exceed two walls between the master mesh router and the slave mesh router; the maximum distance should not exceed 20 meters.
   • Keep the router away from interference sources such as microwave ovens, induction cookers, and refrigerators.
   • Position the router higher from the ground with fewer obstructions around for better performance.
2. When the new mesh router is powered on, wait for approximately 60 seconds for the startup process to complete.
3. Ensure the master mesh router is online. Press the WPS button on both the master and slave mesh routers successively. The Wi-Fi indicator and WPS indicator will start blinking.
4. After about 2-5 minutes, the WPS indicator on the master mesh router and the new mesh router will turn off, and the Wi-Fi indicator will turn white, indicating a successful network connection.

Note: To add another new mesh router, repeat the above steps.

LED Indicator and Explanation

Button Explanation

• WPS: Press the button to build a mesh network.
• Reset: Hold down the WPS button for about 5 seconds and release it to use the WPS connect the device. Hold down for about 6 seconds to restore the factory settings.

FAQ

Q1: How can I remove a mesh router from my Wi-Fi mesh network?

A1: You can remove your router from your network by restoring it to factory settings.

Q2: How to restore my mesh router to factory settings?

A2: With your router powered on, hold down the reset button for about 6 seconds. The LED indicator light will go out. Then the router will restart automatically and restore to factory settings.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement: This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment must be installed and operated in accordance with provided instructions, and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Caution! Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.