Safety Manual NE1611B

Installation Instructions

Position the device vertically on a stable surface, ensuring the foot stand is properly attached.
Wall Mounting: Mounting holes are located on the back of the device. Fasten 2 screws horizontally on the wall (132 mm apart) using hollow wall anchors for stability (see Figure 1). The screw dimensions are illustrated in Figure 2.
Install the unit near a power outlet so that the AC adaptor can be used without stressing the cable, and it can be easily connected to a power outlet. Observe the maximum load of the electrical outlet.
Connect the device according to the installation instructions in Figure 3.

Figure 1: Distance of the Pothook

[Diagram showing hole spacing for wall mounting]

Figure 2: Screw Dimensions

[Diagram showing screw dimensions]

Connect your phone to the TEL1 port. A second device (phone, fax, answering machine) can be connected to the TEL2 port.

Figure 3: Connection Diagram

[Diagram illustrating the connection of power, coaxial cable, phone lines, and Ethernet cables to the device and external components.]

Connect one end of a 75 ohm coaxial cable to the RF cable port. Connect the other end to the cable wall outlet.

Connect the round (DC) connector to the plug on the modem, and the power adaptor into the wall outlet. Push the ON/OFF button down to power up the device.

Connect your computer to one of the Ethernet ports.

IMPORTANT:

READ THESE INSTRUCTIONS BEFORE USING THE DEVICE

EuroDOCSIS / DOCSIS WeMTA

Physical Specifications

Items	Features
Operating Temperature	0 to 40°C
Operating Relative Humidity	10-90% (Non condensing)
Storage Temperature	-40 to 70°C
Dimensions (H x W x D)	218 x 155 x 55mm
Diagnostic LED's (Front)	POWER, US, DS, ONLINE, 2.4G, 5G, TEL1, TEL2
Diagnostic LED's (Rear)	Ethernet Link/Speed

Interfaces

Items	Features
RF Interface	External 'F' type connector
Data Interfaces	4 x 10/100/1000 Base-T Ethernet (RJ-45 connector)
Analog Telephony Interface	2 lines, RJ-11
Input Voltage	100~240VAC, 50/60 Hz

Telephony

Item	Features
Supervisory Voltage	48 Vdc nominal
Ringing Load Capacity	10 REN total; 5 per line
Provisionable High Loop Current Mode	Yes (40mA constant current source)

RF Downstream

Items	Features
Bonded Channels	Up to 24
Tuner Configuration	Full capture tuning range
Frequency Range	108~1002 MHz
Data Rate (Max.)	Up to 1320 Mbps
RF Input Sensitivity Level	-15 to +15 dBmV
Modulation Type	64QAM and 256QAM

RF Upstream

Items	Features
Bonded Channels	Up to 8
Frequency Range	5~85 MHz
Data Rate (Max.)	240 Mbps
RF Output Level	+57 dBmV (32QAM and 64QAM, single upstream) +54 dBmV (32QAM and 64QAM, 4-8 upstreams) +58 dBmV (8QAM and 16QAM, single upstream) +56 dBmV (SCDMA, single upstream) +53 dBmV (SCDMA, 2-8 upstreams)
Modulation Type	QPSK, 8-QAM, 16-QAM, 32-QAM, 64-QAM

Wireless

Items	Features
Frequency Range	2.4GHz and 5GHz
Transmit Power	2.4GHz +20dBm (MCS0), +17dbm (MCS7) 5.8GHz +19dBm (MCS0), +15dbm (MCS9)
Receive Levels	2.4GHz <-80dBM 802.11n (MCS0), <-69dBm 802.11n (MCS7), HT20 5.8GHz <-78dBM 802.11ac (MCS0), <-55dBm 802.11ac (MCS9), VHT80
Spatial Streams (Max.)	5
Data Rate (Max.)	2.4G(2x2): 300Mbps 5G(3x3): 1300Mbps

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices).

This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference,
This device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement:

The equipment complies with FCC Radiation exposure limits set forth for uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Models: NE161134AB, 2AW68-NE161134AB, 2AW68NE161134AB, NE1611B WiFi Cable Modem Router, NE1611B, WiFi Cable Modem Router, Cable Modem Router, Modem Router, Router

File Info : application/pdf, 3 Pages, 3.34MB

GetApplicationAttachment.html?id=5882487 Adobe Illustrator CC 22.0 (Windows) Adobe PDF library 15.00

	NE6037 DOCSIS 3.1 Cable Modem Quick Installation Guide Quick installation guide for the NE6037 DOCSIS 3.1 Cable Modem from Shenzhen SDMC Technology Co., Ltd., detailing package contents, setup instructions, specifications, and FCC compliance.
	NE3034W DOCSIS 3.1 Cable Modem Quick Installation Guide This guide provides quick installation instructions for the NE3034W DOCSIS 3.1 Cable Modem, including package contents, connection diagrams, and technical specifications.
	NM3015 AX3000 Dual Band WiFi 6 Mesh Router Quick Installation Guide A quick installation guide for the NM3015 AX3000 Dual Band WiFi 6 Mesh Router, covering package contents, port descriptions, LED indicators, button functions, and basic setup instructions for master and slave routers.
	Shenzhen SDMC Technology Co., Ltd. NP3081GA-V2 AX3000 Dual Band Wi-Fi GPON Terminal User Guide This document provides a user guide for the Shenzhen SDMC Technology Co., Ltd. NP3081GA-V2 AX3000 Dual Band Wi-Fi GPON Terminal. It covers package contents, ports and indicators, hardware connections, Wi-Fi connection methods (SSID and WPS), web configuration, environmental specifications, FCC statements, and wall mounting instructions.