Mpow X3 True Wireless Earbuds
Model: BH432B
Packing List
- Mpow X3 True Wireless Earbuds (Left and Right)
- Charging Case
- USB-C Charging Cable
- Eartips (Sizes S, M, L)
- User Manual
- VIP Card
Product Overview
The Mpow X3 earbuds feature magnetic charging connectors (?), LED indicator lights (?), ANC/talking microphones (?), and multifunction buttons (?) for touch controls. Each earbud is marked with 'L' or 'R' logos.
The charging case includes an LED indicator light (?) and a Type-C charging port (?).
Pairing
To pair the Mpow X3 earbuds:
- Take the earbuds out of the charging case. They will automatically enter pairing mode, indicated by alternating flashing green and red LED lights (??).
- On your device's Bluetooth settings, select 'Mpow X3' to connect.
Note: The earbuds prioritize reconnecting to the last paired device. To pair with a new device, disable Bluetooth on the previously paired device.
Power On/Off
The earbuds automatically power on when removed from the charging case and power off when placed back inside.
Controls
All controls are performed via the multifunction button (MFB) (?) on each earbud.
ANC Modes
To switch noise-control modes, press and hold the MFB (?) on the Right (R) earbud for 2 seconds. This cycles through three modes:
- ANC Activated: ?
- Voice Through: ?️?
- ANC Off: ⚪
Note: ANC functionality is only available when both earbuds are in use (dual mode). It is not supported in mono mode.
FAQ About ANC Technology
How to experience the ANC effect correctly?
For best results, wear both earbuds in a noisy environment without music playing and toggle ANC on/off. You can also test by listening to ambient noise like air conditioners or traffic.
Is ANC valid when using earbuds for a phone call?
Yes, Mpow X3 offers noise reduction during calls. Note that call noise reduction differs from Active Noise Cancellation (ANC), which is designed for low-frequency ambient noise.
Is ANC valid when wearing only one earbud?
No, ANC is only effective in binaural (dual earbud) mode.
Why is the noise cancelling effect not very significant?
Ensure a proper seal with the correct eartip size, twist earbuds slightly to lock them in place, and test in a noisy environment without music.
Resetting the Earbuds
To reset the Mpow X3 earbuds and clear all paired devices:
- Turn off Bluetooth (?) on your phone or other connected devices.
- Remove the Right (R) earbud from the charging case.
- Press and hold the MFB (?) on the Right (R) earbud for 10 seconds. The red LED (?) will flash three times, indicating the pairing information has been successfully cleared.
Charging
The earbuds charge when placed in the case. The charging case has a Type-C charging port (?). Output: DC 5V.
LED indicators (?) show charging status:
- 0%-25%
- 25%-50%
- 50%-75%
- 75%-100%
Important: Do not place wet earbuds into the charging case.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
This marking (♻️) on the product or its literature indicates it should not be disposed of with household waste. Separate it from other waste and recycle responsibly to promote the sustainable reuse of material resources. Contact your retailer or local government for guidance on environmentally safe recycling.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
