TELTONIKA FMC250 GPS Tracker User Manual

User Manual for TELTONIKA models including: FMC250, FMC250 GPS Tracker, FMC250 Tracker, GPS Tracker, Tracker

FMC250 - Teltonika GPS

You must read these instructions carefully and follow them strictly before operating the device! • The device uses SELV limited power source. The nominal.

21 ore fa — Quick Manual v1.0 // FMC250. 10. QUICK SMS CONFIGURATION ... This sign on the package means that it is necessary to read the User's Manual before your start using ...

1 day ago — Quick Manual v1.0 // FMC250. 10. QUICK SMS CONFIGURATION ... This sign on the package means that it is necessary to read the User's Manual before your start using ...

File Info : application/pdf, 20 Pages, 1.31MB

Quick Manual FMC250 v1.0

FMC250
Advanced watter resistant tracker with CAN data reading feature
Quick Manual v1.0

CONTENT
Know your device................................................................................................................................................................................................3 Pinout ...................................................................................................................................................................................................................4 FMC250-QJIB0 Wiring scheme...........................................................................................................................................................................5 Set up your device ..............................................................................................................................................................................................6 PC Connection (Windows)..................................................................................................................................................................................7 How to install USB drivers (Windows) ..............................................................................................................................................................7 Configuration (Windows) ...................................................................................................................................................................................8 Quick SMS configuration................................................................................................................................................................................. 10 Mounting recommendations.......................................................................................................................................................................... 12 Basic characteristics ........................................................................................................................................................................................ 13 LED indications................................................................................................................................................................................................. 13 Electrical characteristics.................................................................................................................................................................................. 16 Safety information .......................................................................................................................................................................................... 18 Certification and Approvals ............................................................................................................................................................................ 19 Warranty ........................................................................................................................................................................................................... 20 Warranty disclaimer ........................................................................................................................................................................................ 20
Quick Manual v1.0 // FMC250 2

KNOW YOUR DEVICE

TOP VIEW
2x6 SOCKET

BOTTOM VIEW (WITHOUT COVER) TOP VIEW (WITHOUT COVER)
MICRO USB
GSM ANTENNA
NAVIGATE LED

GNSS ANTENNA

BATTERY SOCKET

STATUS LED

CAN LED
MICRO SIM SLOT

Quick Manual v1.0 // FMC250 3

PINOUT

PIN NUMBER PIN NAME

DESCRIPTION

VCC (10-30) V DC (+) Power supply (+10-30 V DC)

Digital input, channel 3 /

DIN 3 / AIN 2

Analog input, channel 2, Input

range: 0-30 V DC

Digital output, channel 3 with

DIN2-N / AIN1

ground sense / Analog input,

DIN1

chanel 1. Input range: 0-30 V DC Digital input, channel 1

CAN1L

CAN2L

CAN2 Low

DIN1

CAN1L

CAN1 Low

DIN2-N/AIN1

GND (-)

Ground

DIN3/AIN2

DOUT 1

DOUT 2

Digital output, channel 1. Open

+10...30 V DC

collector output. Max. 3,3 A DC. FMC250 QJIBO pinout

Digital output, channel 2. Open

collector output. Max. 3,3 A DC.

1WIRE DATA

Data for 1Wire devices.

CAN2H

CAN2 High

CAN1H

CAN1 High

CAN1H

CAN2H

1WIRE DATA

DOUT2

DOUT1

GND

Quick Manual v1.0 // FMC250 4

FMC250-QJIB0 WIRING SCHEME

1WIRE PWR
DIN3 DIN2-N

IGNITION DETECTION
RELAY 87 87a
86 85 30

ALARM BUTTON
DIN2 AIN2
FUEL GAUGE

CAN BUS

CAN1L

CAN2L

DIN1

DIN2-N/AIN1 3

DIN3/AIN2 2

+10...30 V DC 1

CAN1H

CAN2H

10 1WIRE DATA

DOUT2

DOUT1

GND

STARTER

ANALOG LLS SENSOR

DOOR SENSOR

POWER SUPPLY 10 - 30V DC

MULTIPLE TEMPERATURE
SENSORS
BUZZER

IBUTTON LED LIGHTS

Quick Manual v1.0 // FMC250 5

SET UP YOUR DEVICE
HOW TO INSERT MICRO-SIM CARD AND CONNECT THE BATTERY

1 PARTLY CLOSED DEVICE
You will receive your device partly closed.

2 COVER REMOVAL
Gently remove top and bottom covers.

3 SIM CARD INSERT
Insert SIM card as shown with PIN request disabled or read our Wiki1 how to enter it later in Teltonika Configurator2. Make sure that Micro-SIM card cut-off corner is pointing outward from slot. SIM slot 1 is closer to PCB, SIM slot 2 is the top one.
1wiki.teltonika-gps.com/view/FMC230_Security_info 2wiki.teltonika-gps.com/view/Teltonika_Configurator

4 BATTERY CONNECTION
Connect battery as shown to device. Position the battery in place where it does not obstruct other components.

5 ATTACHING COVER BACK
After configuration, see "PC Connection (Windows)1", attach device top and bottom cover back and press them twice to the full closure.
1Page 7, "PC Connection (Windows)

6 COMPLETELY CLOSED DEVICE
Make sure that product casing is closed correctly.

IMPORTANT!
This device has an IP67 casing with a two-phase closing, that ensures reliable protection and ease of use. Please make sure that product casing corner clips are fixed tightly and cable is connected to the device in order to maintain the degree of IP67 protection.

Quick Manual v1.0 // FMC250 6

PC CONNECTION (WINDOWS)
1. Power-up FMC250 with DC voltage (10 30 V) power supply using supplied power cable. LED's should start blinking, see "LED indications1".
2. Connect device to computer using Micro-USB cable or Bluetooth® connection: · Using Micro-USB cable · You will need to install USB drivers, see "How to install USB drivers (Windows)2" · Using Bluetooth® · FMC250 Bluetooth® is enabled by default. Turn on Bluetooth® connection on your PC, then select Add Bluetooth® or other device > Bluetooth®. Choose your device named "FMC250_last_7_imei_digits", without LE in the end. Enter default password 5555, press Connect and then select Done.
3. You are now ready to use the device on your computer.
1wiki.teltonika-gps.com/view/FMC250_LED_status 2Page 7, "How to install USB drivers"
HOW TO INSTALL USB DRIVERS (WINDOWS)
1. Please download COM port drivers from here1. 2. Extract and run TeltonikaCOMDriver.exe. 3. Click Next in driver installation window. 4. In the following window click Install button. 5. Setup will continue installing the driver and eventually the confirmation window will appear. Click Finish to complete the
setup.
1teltonika-gps.com/downloads/en/FMC250/TeltonikaCOMDriver.zip
Quick Manual v1.0 // FMC250 7

CONFIGURATION (WINDOWS)
At first FMC250 device will have default factory settings set. These settings should be changed according to the users needs. Main configuration can be performed via Teltonika Configurator1 software. Get the latest Configurator version from here2. Configurator operates on Microsoft Windows OS and uses prerequisite MS .NET Framework. Make sure you have the correct version installed.
1wiki.teltonika-gps.com/view/Teltonika_Configurator 2wiki.teltonika-gps.com/view/Teltonika_Configurator_versions

MS .NET REQUIREMENTS
Operating system
Windows Vista Windows 7 Windows 8.1 Windows 10

MS .NET Framework version Version

MS .NET Framework 4.6.2

32 and 64 bit

1dotnet.microsoft.com/en-us/download/dotnet-framework/net462

Links www.microsoft.com1

Quick Manual v1.0 // FMC250 8

Various Status window1 tabs display information about GNSS2, GSM3, I/O4, Maintenance5 and etc. FMC250 has one user editable profile, which can be loaded and saved to the device. After any modification of configuration the changes need to be saved to device using Save to device button. Main buttons offer following functionality:

Downloaded Configurator will be in compressed archive.
Extract it and launch Configurator.exe. After launch software
language can be changed by clicking in the right bottom corner.
FMC250
Configuration process begins by pressing on connected device.

Load from device loads configuration from device. Save to device saves configuration to device. Load from file loads configuration from file. Save to file saves configuration to file. Update firmware updates firmware on device. Read records reads records from the device.

FFMMCC125500
After connection to Configurator Status window will be displayed.

Reboot device restarts device.
Reset configuration sets device configuration to default.
Most important configurator section is GPRS where all your server and GPRS settings6 can be configured and Data Acquisition7 where data acquiring parameters can be configured. More details about FMC250 configuration using Configurator can be found in our Wiki8. 1wiki.teltonika-gps.com/view/FMC250_Status_info 2wiki.teltonika-gps.com/view/FMC250_Status_info#GNSS_Info 3wiki.teltonika-gps.com/view/FMC2501_Status_info#GSM_Info 4wiki.teltonika-gps.com/view/FMC250_Status_info#I.2FO_Info 5wiki.teltonika-gps.com/view/FMC250_Status_info#Maintenance 6wiki.teltonika-gps.com/index.php?title=FMC250_GPRS_settings 7wiki.teltonika-gps.com/index.php?title=FMC250_Data_acquisition_ settings 8wiki.teltonika-gps.com/index.php?title=FMC250_Configuration

Quick Manual v1.0 // FMC250 9

QUICK SMS CONFIGURATION

Default configuration has optimal parameters present to ensure best performance of track quality and data usage. Quickly set up your device by sending this SMS command to it:

« setparam 2001:APN;2002:APN_username;2003:APN_password;2004:Domain;2005:Port;2006:0»

Note: Before SMS text, two space symbols should be inserted.

GPRS SETTINGS: 1 2001 APN

2 2002 APN username (if there are no APN username, empty field should be left)

2003 APN password (if there are no APN password, empty field should be left)

SERVER SETTINGS: 4 2004 Domain 5 2005 Port 6 2006 Data sending protocol (0 TCP, 1 UDP)

Quick Manual v1.0 // FMC250 10

DEFAULT CONFIGURATION SETTINGS
MOVEMENT AND IGNITION DETECTION:

DEVICE MAKES A RECORD ON MOVING IF ONE OF THESE EVENTS HAPPEN:

VEHICLE MOVEMENT will be detected by accelerometer

IGNITION will be detected by vehicle power voltage between 13,2 30 V

DEVICE MAKES A RECORD ON STOP IF:

RECORDS SENDING TO SERVER:

PASSES 300 seconds

VEHICLE DRIVES 100 meters

VEHICLE TURNS 10 degrees

SPEED DIFFERENCE between last coordinate and current position is greater than 10 km/h

1 HOUR PASSES while vehicle is stationary and ignition is off

EVERY 120 SECOND it is sent to the server If device has made a record

After successful SMS configuration, FMC250 device will synchronize time and update records to configured server. Time intervals and default I/O elements can be changed by using Teltonika Configurator1 or SMS parameters2.
1wiki.teltonika-gps.com/view/Teltonika_Configurator 2wiki.teltonika-gps.com/view/Template:FMC_Device_Family_Parameter_list
Quick Manual v1.0 // FMC250 11

MOUNTING RECOMMENDATIONS
CONNECTING WIRES
· Wires should be fastened to the other wires or non-moving parts. Try to avoid heat emitting and moving objects near the wires.
· The connections should not be seen very clearly. If factory isolation was removed while connecting wires, it should be applied again.
· If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be applied.
· Wires cannot be connected to the board computers or control units.
CONNECTING POWER SOURCE
· Be sure that after the car computer falls asleep, power is still available on chosen wire. Depending on car, this may happen in 5 to 30 minutes period.
· When module is connected, measure voltage again to make sure it did not decrease. · It is recommended to connect to the main power cable in the fuse box. · Use 3A, 125V external fuse.
CONNECTING IGNITION WIRE
· Be sure to check if it is a real ignition wire i. e. power does not disappear after starting the engine. · Check if this is not an ACC wire (when key is in the first position, most of the vehicle electronics are available). · Check if power is still available when you turn off any of vehicles devices. · Ignition is connected to the ignition relay output. As alternative, any other relay, which has power output when ignition is on,
may be chosen.
CONNECTING GROUND WIRE
· Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame. · If the wire is fixed with the bolt, the loop must be connected to the end of the wire. · For better contact scrub paint from the spot where loop is going to be connected.
Quick Manual v1.0 // FMC250 12

LED INDICATIONS

NAVIGATION LED INDICATIONS

BEHAVIOUR

MEANING

Permanently switched on

GNSS signal is not received

Blinking every second Normal mode, GNSS is working

GNSS is turned off because:

Off

Device is not working or Device is in

sleep mode

Blinking fast constantly

Device firmware is being flashed

STATUS LED INDICATIONS

BEHAVIOUR

MEANING

Blinking every second Normal mode

Blinking every two seconds

Sleep mode

Blinking fast for a short time

Modem activity

Off

Device is not working or Device is in boot mode

CAN STATUS LED INDICATIONS

BEHAVIOUR

MEANING

Blinking very fast

FW is being flashed for CAN IC

Fast blinking

The flashed FW image is corrupted or not found

Short blink and long No CAN configuration uploaded in

wait

device

2 short blinks and long wait

CAN configuration is loaded for parsing CAN data

3 short blinks and long wait

Data is being read from CAN bus

BASIC CHARACTERISTICS

MODULE Name Technology

FMC250-QJIB0: Quectel EG915U-EU
GSM, GPRS, GNSS, BLUETOOTH LE, LTE

GNSS GNSS Receiver Tracking sensitivity

GPS, GLONASS, GALILEO, BEIDOU, QZSS, AGPS
Tracking: 33
-165 dBM

Quick Manual v1.0 // FMC250 13

Accuracy Hot start Warm start Cold start CELLULAR Technology 2G bands 4G bands
Data transfer
Data support
Transmit power

< 3 m < 1 s < 25 s < 35 s
LTE Cat 1, GSM FMC250-QJIB0: GSM: B2/B3/B5/B8 FMC250-QJIB0: LTE FDD: B1/B3/B5/ B7/B8/B20/B28 LTE: LTE FDD : Max 10Mbps (DL)/ Max 5Mbps (UL) GSM: GPRS: Max 85.6Kbps (DL)/ Max 85.6Kbps (UL) SMS (text/data)
Class 5 for GSM900: 36dBm Class 3 for DCS1800: 33dBm Class 3 for LTE-FDD: 25.7dBm Bluetooth®: 5.56dBm Bluetooth® LE: -3.17dBm

POWER

Input voltage range

10-30 V DC with overvoltage protection

Back-up battery

170 mAh Li-Ion battery 3.7 V (0.63 Wh)

Internal fuse

3 A, 125 V

Power Consumption

At 12V < 6 mA (Ultra Deep Sleep1) At 12V < 8 mA (Deep Sleep2) At 12V < 11 mA (Online Deep Sleep3) At 12V < 20 mA (GPS Sleep4) At 12V < 35 mA (nominal with no load)
At 12V < 250 mA Max. (with full Load/ Peak)

BLUETOOTH® TECHNOLOGY

Specification

4.0 + LE

Supported peripherals

Temperature and Humidity sensor5, Inateck Barcode Scanner, Universal Bluetooth® LE sensors support

INTERFACE Digital Inputs Negative Inputs Impuls Inputs Analog Inputs

FMC250-QJIB0: 3
FMC250-QJIB0: 1 (Digital Input 2) FMC250-QJIB0: 2 (Digital Input 1, Digital Input 2) FMC250-QJIB0: 2

1wiki.teltonika-gps.com/view/FMC250_Sleep_modes#Ultra_Deep_Sleep_ mode 2wiki.teltonika-gps.com/view/FMC250_Sleep_modes#Deep_Sleep_mode 3teltonika-gps.com/view/FMC250_Sleep_modes#Online_Deep_Sleep_ mode 4wiki.teltonika-gps.com/view/FMC250_Sleep_modes#GPS_Sleep_mode 5teltonika.lt/product/bluetooth-sensor/
Quick Manual v1.0 // FMC250 14

Digital outputs CAN interfaces 1-Wire
GNSS antenna
GSM antenna USB LED indication SIM Memory

FMC250-QJIB0: 2 2 1 (1-Wire data)
Internal High Gain
Internal High Gain 2.0 Micro-USB 3 status LED lights Micro-SIM or eSIM 128MB internal flash memory

PHYSICAL SPECIFICATION

Dimensions

70,5 x 67,0 x 25,6 mm (L x W x H)
85,0 x 67,0 x 25,6 mm (L x W x H) (length with connector socket)

Weight

73.5 g

OPERATING ENVIRONMENT

Operating temperature (without battery)

-40 °C to +85 °C

Storage temperature (without battery)

-40 °C to +85 °C

Operating temperature (with battery)

-20 °C to +40 °C

Storage temperature -20 °C to +45 °C for 1 month

(with battery)

-20 °C to +35 °C for 6 months

Operating humidity 5% to 95% non-condensing

Ingress Protection Rating
Battery charge temperature
Battery storage temperature

IP67
0 °C to +45 °C -20 °C to +45 °C for 1 month -20 °C to +35 °C for 6 months

FEATURES CAN Data Sensors
Scenarios

Fuel Level (Dashboard), Total fuel consumption, Vehicle speed (wheel), Vehicle driven distance, Engine speed (RPM), Accelerator pedal position
Accelerometer
Green Driving, Over Speeding detection, Jamming detection, GNSS Fuel Counter, DOUT Control Via Call, Excessive Idling detection, Immobilizer, iButton Read Notification, Unplug detection, Towing detection, Crash detection, Auto Geofence, Manual Geofence, Trip6

6wiki.teltonika-gps.com/view/FMC250_Accelerometer_Features_settings Quick Manual v1.0 // FMC250 15

Sleep modes

GPS Sleep, Online Deep Sleep, Deep Sleep, Ultra Deep Sleep7

Configuration and firmware update

FOTA Web8, FOTA9, Teltonika Configurator10 (USB, Bluetooth® wireless technology), FMBT mobile application11 (Configuration)

SMS

Configuration, Events, DOUT control, Debug

GPRS commands

Configuration, DOUT control, Debug

Time Synchronization GPS, NITZ, NTP

Ignition detection

Digital Input 1, Accelerometer, External Power Voltage, Engine

7wiki.teltonika-gps.com/view/FMC250_Sleep_modes 8wiki.teltonika.lt/view/FOTA_WEB 9wiki.teltonika.lt/view/FOTA 10wiki.teltonika.lt/view/Teltonika_Configurator 11teltonika.lt/product/fmbt-mobile-application/

ELECTRICAL CHARACTERISTICS

CHARACTERISTIC DESCRIPTION
MIN.

SUPPLY VOLTAGE

Supply Voltage

(Recommended

+10

Operating Conditions)

VALUE

TYP.

MAX. UNIT

+30

DIGITAL OUTPUT (OPEN DRAIN GRADE)

Drain current (Digital Output OFF)

120

µA

Drain current (Digital Output ON, Recommended Operating Conditions)

0.1

0.5

Static Drain-Source resistance (Digital Output ON)

400

600

DIGITAL INPUT

Input resistance (DIN1) 47

Input resistance (DIN2) 38.45

Quick Manual v1.0 // FMC250 16

CHARACTERISTIC DESCRIPTION
MIN.

Input resistance (DIN3) 150

Input voltage

(Recommended

Operating Conditions)

Input Voltage threshold (DIN1)

Input Voltage threshold (DIN2)

Input Voltage threshold (DIN3)

VALUE

TYP.

MAX. UNIT

Supply voltage

7.5

2.5

OUTPUT SUPPLY VOLTAGE 1-WIRE

Supply voltage

+4.5

Output inner resistance

Output current (Uout > 3.0 V)

Short circuit current (Uout = 0)

+4.7 V mA
mA

NEGATIVE INPUT
Input resistance
Input voltage (Recommended Operating Conditions)

38.45 0

Supply voltage

CHARACTERISTIC DESCRIPTION
MIN.
Input voltage threshold
Sink current

VALUE

TYP.

MAX. UNIT

0.5

180

CAN INTERFACE

Internal terminal

resistors CAN bus (no internal termination

resistors)

Differential input resistance

Recessive output voltage

2.5

Differential receiver threshold voltage

0.5

0.7

0.9

Common mode input voltage

-30

Quick Manual v1.0 // FMC250 17

SAFETY INFORMATION
This message contains information on how to operate FMC250 safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!
· The device uses SELV limited power source. The nominal voltage is +12 V DC. The allowed voltage range is +10...+30 V DC.
· To avoid mechanical damage, it is advised to transport the device in an impact-proof package. Before usage, the device should be placed so that its LED indicators are visible. They show the status of device operation.
· When connecting the 2x6 connector wires to the vehicle, the appropriate jumpers of the vehicle power supply should be disconnected.
· Before unmounting the device from the vehicle, the 2x6 connector must be disconnected. The device is designed to be mounted in a zone of limited access, which is inaccessible to the operator. All related devices must meet the requirements of EN 62368-1 standard. The device FMC250 is not designed as a navigational device for boats.

Do not disassemble the device. If the device is damaged, the power supply cables are not isolated or the isolation is damaged, DO NOT touch the device before unplugging the power supply.
All wireless data transferring devices produce interference that may affect other devices which are placed nearby.
The device must be connected only by qualified personnel.
The device must be firmly fastened in a predefined location.
The programming must be performed using a PC with autonomic power supply.
Installation and/or handling during a lightning storm is prohibited.
The device is susceptible to water and humidity if the device housing is not properly closed
CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
Battery should not be disposed of with general household waste. Bring damaged or worn-out batteries to your local recycling center or dispose them to battery recycle bin found in stores.
Quick Manual v1.0 // FMC250 18

CERTIFICATION AND APPROVALS

This sign on the package means that it is necessary to read the User`s Manual before your start using the device. Full User`s Manual version can be found in our Wiki1.
1wiki.teltonika-gps.com/index.php?title=FMC250

This sign on the package means that all used electronic and electric equipment should not be mixed with general household waste.

Hereby, Teltonika declare under our sole responsibility that the above described product is in conformity with the relevant Community harmonization: European Directive 2014/53/EU (RED).

The RoHS1 is a directive regulating the manufacture, import and distribution of Electronics and Electrical Equipment (EEE) within the EU, which bans from use 10 different hazardous materials (to date).

UK Conformity Assessed (UKCA) marking is a conformity mark that indicates conformity with the applicable requirements for above described products sold within Great Britain.

E57

E-Mark and e-Mark are the European conformity marks issued by the transport sector, indicating that the products comply with relevant laws and regulations or directives. Vehicles and related products need to go through the E-Mark certification process to be legally sold in Europe.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by UAB Teltonika Telematics is under license. Other trademarks and trade names are those of their respective owners.

CHECK ALL CERTIFICATES
All newest certificates may be found in our Wiki2. 2 wiki.teltonika-gps.com/view/FMC250_Certification_%26_Approvals

Quick Manual v1.0 // FMC250 19

WARRANTY
We guarantee our products 24-month warranty1 period. All batteries carry a 6-month warranty period. Post-warranty repair service for products is not provided. If a product stops operating within this specific warranty time, the product can be: · Repaired · Replaced with a new product · Replaced with an equivalent repaired product fulfilling the same functionality · Replaced with a different product fulfilling the same functionality in case of EOL for the original product
1Additional agreement for an extended warranty period can be agreed upon separately.
WARRANTY DISCLAIMER
· Customers are only allowed to return products as a result of the product being defective, due to order assembly or manufacturing fault.
· Products are intended to be used by personnel with training and experience. · Warranty does not cover defects or malfunctions caused by accidents, misuse, abuse, catastrophes, improper maintenance
or inadequate installation not following operating instructions (including failure to heed warnings) or use with equipment with which it is not intended to be used. · Warranty does not apply to any consequential damages. · Warranty is not applicable for supplementary product equipment (i. e. PSU, power cables, antennas) unless the accessory is defective on arrival. · More information on what is RMA1
1wiki.teltonika-gps.com/view/RMA_guidelines
Quick Manual v1.0 // FMC250 20

References

Adobe PDF Library 17.0 Adobe InDesign 19.0 (Windows)