HOLOMARQ Sequra H2 Fingerprint Door Knob with Keypad

Hello!

Thank you for choosing the Sequra Fingerprint Door Knob With Keypad! Sequra enhances indoor room security with its robust Zinc Alloy body. It supports up to 50 passcodes and 100 fingerprints, offering versatile use cases. Features like Passage Mode, Auto-Lock, and Anti-Peep passcode provide convenience. With power-saving technology, 4 AA batteries offer up to 2 years of battery life, allowing you to use your key as a backup.

Explore all features in this manual. For questions, contact customer support:

• Email: support@marqsmart.com
• Website: www.marqsmart.com

What's in the Box

The package includes:

• Exterior Assembly
• Interior Assembly
• Latch Assembly
• Keys (x2)
• Strike Plate
• Strike Box
• Screws for door thickness 48mm or above (M4 x 2)
• Screws for door thickness 35-48mm (M4 x 2)
• Screws for door knob set (M4 x 1)
• Strike Plate Screws (4/5" or 20mm) (x4)
• Cable Wire
• Rod Bolts
• Fingerprint Sensor
• USB-C Port
• Battery Compartment
• Interior Cover
• Screws

Tools Required

• Phillips Screwdriver
• Drill
• Hole Saw Drill
• Chisel
• Hammer
• Tape Measure
• Pencil

Batteries

Requires 4 AA Alkaline batteries (Duracell or Energizer recommended), sold separately. 1.2V Rechargeable batteries are not recommended. When batteries are correctly installed, a long beep will sound, and the keypad will illuminate green.

Important: DO NOT mix new and used batteries. Use new batteries from a single brand.

Installation Guide

Step 1: Prepare the door and check dimensions

For installation on new doors:

1. Prepare door and jamb: Take out the 'Door Marking Template'. Fold and place it on the door 36" (915mm) from the ground.
2. Mark the door for drilling: Mark the center hole on the door edge for the 1" (25mm) latch bolt. Mark the center hole on the door face for the 2-3/8" (60mm) or 2-3/4" (70mm) backset.
3. Drill and chisel door: Drill a 2-1/8" (54mm) hole through the door face. Drill a 1" (25mm) hole in the door edge for the latch assembly. Insert the latch assembly, ensuring it's parallel to the door face. Mark the outline and remove the latch. Chisel 1/8" (3mm) deep or until the latch face is flush with the door edge.
4. Mark and drill door jamb: Mark the center hole on the jamb edge, aligned with the latch bolt. Drill a hole in the jamb. Check if the strike plate fits. Outline the strike plate edges and chisel 1/8" (3mm) deep. Install the strike plate using the provided screws.

For installation on doors with pre-drilled holes:

1. Check door compatibility / Remove existing door knob (if applicable). Ensure the door has compatible pre-drilled holes.
2. Double-check door dimensions: Verify backset (2-3/8" or 2-3/4"), door thickness (1-3/8" to 2.5"), hole in the door (2-1/8"), and hole in the door edge (1").

General Installation Notes:

• DO NOT use an electric screwdriver; hand-tighten screws with a Phillips screwdriver.
• DO NOT over-tighten screws.
• DO NOT install if the door thickness is out of range.

Step 2: Install the Latch and Strike Plate

• Hold the latch in front of the door hole, with the latch face flush against the door edge. Ensure the square-shaped hole is centered.
• For a 2-3/4" (70mm) backset, pull to extend the latch to center the squared-shaped hole.
• Install the latch using screws.
• In most cases, the existing strike plate can be used. If not, ensure the bolt aligns correctly with the strike plate.

Step 3: Install the Exterior Assembly

• Ensure the door is open.
• Make sure the keyhole is in a vertical position.
• Insert the Exterior Assembly onto the door, aligning rod bolts with the latch's round holes and the square spindle and control wire with the square-shaped hole. The "UP" mark on the spindle should face upward.
• Connect the control wire to the female socket on the battery compartment. Forcing the control wire elsewhere may damage the connector.

Step 4: Install the Interior Assembly

1. Remove the top screw and pull out the cover.
2. Install the interior knob onto the door, aligning rod bolts with the latch's round holes and the square spindle and control wire with the square-shaped hole.
3. Secure both knobs using the 2-3/8" (60mm) or 1-3/5" (40mm) screws. Tighten with a Phillips screwdriver, but DO NOT over-tighten.
4. Plug the control wire male plug into the female socket on the battery compartment.
5. Install the batteries.
6. Press and hold the reset button until a long beep is heard.
7. Install and secure the cover with the screw.

Step 5: Testing door knob

• Always test with the door open.
• Ensure both interior and exterior knobs are not slanted.
• Enter the default admin passcode (010203) and test the exterior knob; the bolt should move smoothly.
• Use keys to test the exterior knob; the bolt should move smoothly.
• Test the interior knob; the bolt should move smoothly.
• Close the door to ensure the bolt fits correctly in the jamb hole.

NOTE:

• Ensure the door knob has been reset successfully.
• If you forget your passcode or your fingerprint is not recognized, use backup keys.
• If backup keys are lost, contact a locksmith immediately.

Congratulations! Sequra is ready for use. ?

Step 6: Using door knob

Indicator Lights and Buzzer

• Indicator Light: Green indicates success or unlocking; Red indicates failure or low battery.
• Fingerprint Ring Light: Green for successful read, Red for failed read, Blue for reading, White for initializing.
• Enter button
• USB-C Port
• Fingerprint Area

Important Tips

• Lift and rest your finger on the fingerprint sensor repeatedly for 6 times.
• For best results, scan five fingerprint areas following the 6-step sequence when adding a fingerprint.

Batteries

Requires 4 AA Alkaline batteries (Duracell or Energizer recommended), sold separately. 1.2V Rechargeable batteries are not recommended. When batteries are correctly installed, a long beep will sound, and the keypad will illuminate green.

If batteries die due to long idle time, use a USB-C cable with a power source (like a power bank) for emergency power. Replace batteries immediately after successful unlocking.

Buzzer and Status Indicator

Account management

• Administrator Passcode: Default is '010203'. Set a new 4-8 digit code after installation.
• Change Administrator Passcode: > Old admin passcode > 0 > New admin passcode > New passcode (confirm)
• Add a User Passcode: > Admin passcode > 1 > New passcode > New passcode (confirm)
• Change a User Passcode: > Admin passcode > 2 > Old passcode > New passcode > New passcode (confirm)
• Add a Fingerprint: > Admin passcode > 3 > Lift and rest finger on the fingerprint area 6 times.
• Delete a User Passcode: > Admin passcode > 7 > Old passcode
• Delete a Fingerprint: > Admin passcode > 8 > Rest enrolled finger on fingerprint area > Green lights + long beep
• Delete All User Passcodes: > Admin passcode > 97 > 97 (Admin passcode remains)
• Delete All Fingerprints: > Admin passcode > 98 > 98
• Clear all users: > Admin passcode > 99 > 99

Settings

• Resetting the Door Knob: Remove the interior assembly cover. Press and hold the Reset Button until a long beep and green light are heard, followed by another long beep and green light, indicating a successful reset.
• Passage Mode: The door remains unlocked until turned off.
  • Standard Settings: > Admin. passcode > 4
  • Shortcut: > Admin. passcode > Press and hold for 5s
  • Turn off passage mode: Press any key to deactivate.

  *Once succeeded, green light stays for a while with a long beep.

• Anti-Peep: Protects your passcode from prying eyes. Enter up to 20 digits, including your passcode, to unlock.
• Auto-Lock: The door automatically locks after 5 seconds. Passage Mode disables Auto-Lock; it resumes when Passage Mode is off.
• Silent Mode (Buzzer): Turn on/off by > Admin. passcode > 6. This deactivates the buzzer.
• Immediate locking: Press the lock button to lock immediately.

Troubleshooting

• Failed to read fingerprint: Clean the sensor, ensure finger is clean and dry, place finger in the same position, check for damage, or re-add the fingerprint.
• No indicator nor sound response: Check cable wire connection, battery polarity and level, and ensure Silent Mode is off. Use USB-C for emergency power if locked out.
• Latch will not extend or retract: Check door edge hole size, latch installation, and knob orientation.
• Bolt is not able to go through the strike plate: Ensure bolt alignment with the strike plate, smooth sliding, and correct hole depth in the jamb.
• Failed to unlock using a passcode: Reset the door knob, use the administrator passcode to modify the user passcode, or check button functionality (turn off Silent Mode).
• Failed to lock or unlock/Failed to fully turn the knob: Check for overtightened screws, slanted knobs, and ensure proper battery level with no mixed battery types.

Important safeguard

• Protect your administrator code by setting a separate user code for daily use.
• Promptly remove unused fingerprints. Consider deleting all fingerprints or resetting the lock if uncertain.
• Double-check user codes when sending them.
• Dispose of used batteries according to local laws.
• Always have access to your lock's standard key.
• Prevent liquids from entering the lock's electrical parts or battery compartment.
• Replace batteries immediately when warned.

CAUTION: Prevent unauthorized entry. Regularly check the administrator code for alterations, as anyone with interior access can factory reset the knob.

WARNING: No lock offers complete security alone. This lock can be bypassed by force, technical means, or entry elsewhere. Caution, environmental awareness, and common sense are crucial. Consult a qualified locksmith or security professional for enhanced security.