REMOTE CONTROLLER OWNER'S MANUAL

Remote Controller Specifications

Quick Start Guide

NOT SURE WHAT A FUNCTION DOES? Refer to the 'How to Use Basic Functions' and 'How to Use Advanced Functions' sections of this manual for a detailed description of how to use your air conditioner.

SPECIAL NOTE:

• Button designs on your unit may differ slightly from the example shown.
• If the indoor unit does not have a particular function, pressing that function's button on the remote control will have no effect.
• When there are wide differences between "Remote controller Manual" and "USER'S MANUAL" on function description, the description of "USER'S MANUAL" shall prevail.

Handling the Remote Controller

Inserting and Replacing Batteries

Your air conditioning unit may come with two batteries (some units). Put the batteries in the remote control before use.

BATTERY NOTES

For optimum product performance:

• Do not mix old and new batteries, or batteries of different types.
• Do not leave batteries in the remote control if you don't plan on using the device for more than 2 months.

BATTERY DISPOSAL

Do not dispose of batteries as unsorted municipal waste. Refer to local laws for proper disposal of batteries.

TIPS FOR USING REMOTE CONTROL

• The remote control must be used within 8 meters of the unit.
• The unit will beep when remote signal is received.
• Curtains, other materials, and direct sunlight can interfere with the infrared signal receiver.
• Remove batteries if the remote will not be used more than 2 months.

NOTES FOR USING REMOTE CONTROL

The device could comply with local national regulations.

• In Canada, it should comply with CAN ICES-3(B)/NMB-3(B).
• In USA, this device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
  • (1) This device may not cause harmful interference, and
  • (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not approved by the party responsible for compliance could void user's authority to operate the equipment.

Buttons and Functions

Before you begin using your new air conditioner, make sure to familiarize yourself with its remote control. The following is a brief introduction to the remote control itself. For instructions on how to operate your air conditioner, refer to the 'How to Use Basic Functions' section of this manual.

Remote Model RG10F(D)/BGEF, RG10F1(D)/BGEF:

• Mode: Selects operation mode.
• SET: Used to select functions.
• OK: Confirms selected functions.
• Swing: Controls louver movement.
• Timer on: Sets timer to turn unit on.
• Timer off: Sets timer to turn unit off.
• LED: Controls indoor unit display and buzzer.
• [Power Symbol]: Turns the unit on or off.

Remote Model RG10F(E)/BGEF, RG10F1(E)/BGEF:

• Mode: Selects operation mode.
• SET: Used to select functions.
• OK: Confirms selected functions.
• Swing: Controls louver movement.
• Timer on: Sets timer to turn unit on.
• Timer off: Sets timer to turn unit off.
• LED: Controls indoor unit display and buzzer.
• iSense: Temperature sensing and room temperature display.
• [Power Symbol]: Turns the unit on or off.

Remote Model RG10F(F/G/H/S)/BGEF, RG10F1(F/G/H)/BGEF:

• Mode: Selects operation mode.
• SET: Used to select functions.
• OK: Confirms selected functions.
• Swing: Controls louver movement.
• Timer on: Sets timer to turn unit on.
• Timer off: Sets timer to turn unit off.
• LED: Controls indoor unit display and buzzer.
• iSense: Temperature sensing and room temperature display.
• [Power Symbol]: Turns the unit on or off.

NOTE: Press SET button to select the operation functions in the following order: Fresh (?️) → AP mode (?) → Fresh...

The selected symbol will flash on the display area, press the OK button to confirm.

Fresh feature is not available for models of RG10F(D)/BGEF, RG10F(E)/BGEF and RG10F(F/G/H/S)/BGEF.

Remote Model RG10F2(D1)/BGEFU1, RG10F3(D1)/BGEFU1:

• Mode: Selects operation mode.
• SET: Used to select functions.
• OK: Confirms selected functions.
• Swing: Controls louver movement.
• Timer on: Sets timer to turn unit on.
• Timer off: Sets timer to turn unit off.
• LED: Controls indoor unit display and buzzer.
• [Temp Up/Down]: Adjusts temperature.
• °C/°F: Switches temperature display.
• [Power Symbol]: Turns the unit on or off.

Remote Model RG10F2(E1)/BGEFU1, RG10F3(E1)/BGEFU1:

• Mode: Selects operation mode.
• SET: Used to select functions.
• OK: Confirms selected functions.
• Swing: Controls louver movement.
• Timer on: Sets timer to turn unit on.
• Timer off: Sets timer to turn unit off.
• LED: Controls indoor unit display and buzzer.
• iSense: Temperature sensing and room temperature display.
• [Temp Up/Down]: Adjusts temperature.
• °C/°F: Switches temperature display.
• [Power Symbol]: Turns the unit on or off.

Remote Model RG10F2(F1/G1/H1)/BGEFU1, RG10F3(F1/G1/H1)/BGEFU1:

• Mode: Selects operation mode.
• SET: Used to select functions.
• OK: Confirms selected functions.
• Swing: Controls louver movement.
• Timer on: Sets timer to turn unit on.
• Timer off: Sets timer to turn unit off.
• LED: Controls indoor unit display and buzzer.
• iSense: Temperature sensing and room temperature display.
• [Temp Up/Down]: Adjusts temperature.
• °C/°F: Switches temperature display.
• [Power Symbol]: Turns the unit on or off.

NOTE: Press SET button to select the operation functions in the following order: Fresh (?️) → I Sense (?️) → AP mode (?) → Fresh...

The selected symbol will flash on the display area, press the OK button to confirm.

Fresh feature is not available for models of RG10F2(D1)/BGEFU1, RG10F2(E1)/BGEFU1 and RG10F2(F1/G1/H1)/BGEFU1.

Button Functions Explained

• [Power Symbol] ON/OFF: Turns the unit on or off.
• TEMP [Up Arrow]: Increases temperature in 1°C (1°F) increments. Max. temperature is 30 °C (86 °F).
• TEMP [Down Arrow]: Decreases temperature in 1 °C (1 °F) increments. Max. temperature is 17 °C (62 °F).
• FAN SPEED: Selects fan speeds in the following order: AUTO → LOW → MED → HIGH.
  NOTE: Holding this button down for 2 seconds will activate Silence feature (some units).
• TIMER ON: Sets timer to turn unit on (refer to 'How to Use Basic Functions' for instructions).
• MODE: Scrolls through operation modes as follows: AUTO → COOL → DRY → HEAT → FAN.
  NOTE: HEAT mode is not supported by cooling-only appliances.
• SHORTCUT: Used to restore the current settings or resume previous settings.
• OK: Used to confirm the selected functions.
• SWING: Starts and stops the horizontal louver movement. Hold down for 2 seconds to initiate vertical louver auto swing feature (some units).
• TIMER OFF: Sets timer to turn unit off (refer to 'How to Use Basic Functions' for instructions).
• I SENSE: Temperature sensing and room temperature display button.
• SLEEP (☰): Saves energy during sleeping hours.
• LED (?): Turns indoor unit's LED display and air conditioner buzzer (some units) on and off, creating a comfortable and quiet environment.
• °C/°F: Press this button to alternate the temperature display between °C and °F.
• LOCK (?): Press together the two buttons simultaneously for 5 seconds to lock the keyboard. Press together the two buttons for 2 seconds to unlock the keyboard.

Remote Screen Indicators

Information is displayed when the remote controller is powered up.

• Transmission Indicator: Lights up when the remote sends a signal to the indoor unit.
• Fresh feature display (?, some units): No display when Fresh feature is activated.
• Sleep mode display (?).
• I Sense feature display (?).
• Wireless control feature display (?).
• Low battery detection display (?, if flashes).
• MODE display: Displays the current mode, including AUTO, COOL, DRY, HEAT, FAN.
• TIMER ON display (?).
• TIMER OFF display (?).
• Not available for this unit.
• FAN SPEED display: Displays selected fan speed: LOW, MED, HIGH, AUTO.
  This fan speed cannot be adjusted in AUTO or DRY mode.
• ECO display: Not available for this unit.
• LOCK display (?): Displays when LOCK feature is activated.
• Temperature/Timer/Fan speed display: Displays the set temperature by default, or fan speed or timer setting when using TIMER ON/OFF functions.
  
  • Temperature range: 17-30°C/62-86°F
  • Timer setting range: 0-24 hours
  This display is blank when operating in FAN mode.

Note: All indicators shown in the figure are for the purpose of clear presentation. During actual operation, only the relative function signs are shown on the display window.

How to Use Basic Functions

ATTENTION: Before operation, please ensure the unit is plugged in and power is available.

SETTING TEMPERATURE

The operating temperature range for units is 17-30°C (62-86°F). You can increase or decrease the set temperature in 1°C (1°F) increments.

AUTO Mode

NOTE:

• In AUTO mode, the unit will automatically select the COOL, FAN, or HEAT function based on the set temperature.
• In AUTO mode, fan speed cannot be set.

COOL or HEAT Mode

NOTE: As outdoor temperature drops, the performance of your unit's HEAT function may be affected. In such instances, it is recommended to use this air conditioner in conjunction with other heating appliances.

DRY Mode

NOTE: In DRY mode, fan speed cannot be set since it has already been automatically controlled.

FAN Mode

NOTE: In FAN mode, you cannot set the temperature. As a result, no temperature displays on the remote screen.

Setting the TIMER

TIMER ON/OFF - Set the amount of time after which the unit will automatically turn on/off.

TIMER ON setting

TIMER OFF setting

NOTE:

• When setting the TIMER ON or TIMER OFF, the time will increase by 30-minute increments with each press, up to 10 hours. After 10 hours and up to 24, it will increase in 1-hour increments. (For example, press 5 times to get 2.5h, and press 10 times to get 5h.) The timer will revert to 0.0 after 24 hours.
• Cancel either function by setting its timer to 0.0h.

TIMER ON & OFF setting (example)

Keep in mind that the time periods you set for both functions refer to hours after the current time.

How to Use Advanced Functions

Swing function

LED DISPLAY

FP function

The unit will operate at high fan speed (while compressor is on) with the temperature automatically set to 8°C/46°F.

Note: This function is for heat pump air conditioners only.

To activate FP function, press this button 2 times during one second under HEAT Mode and setting temperature of 17°C/62°F. Pressing On/Off, Sleep, Mode, Fan, and Temp. buttons while operating will cancel this function.

SHORTCUT function

Push the 'SHORTCUT' button when the remote controller is on; the system will automatically revert back to the previous settings, including operating mode, setting temperature, fan speed level, and sleep feature (if activated).

If pushing for more than 2 seconds, the system will automatically restore the current operation settings, including operating mode, setting temperature, fan speed level, and sleep feature (if activated).

SLEEP function (?)

The SLEEP function is used to decrease energy use while you sleep (and you don't need the same temperature settings to stay comfortable). This function can only be activated via remote control. The sleep function is not available in Fan or Dry mode. Please refer to the OWNER'S MANUAL for more details.

SET function

To cancel the selected function, just perform the same procedures as above.

Press the 'SET' button to scroll through operation functions as follows: Fresh (?) → I Sense (?) → AP mode (?)

[*]: If your remote controller has an 'I Sense' button, you cannot use the 'SET' button to select the I Sense feature.

FRESH function (?, some units)

When the FRESH function is initiated, the ion generator is energized and will help to purify the air in the room.

AP function (?, some units)

Choose AP mode to do wireless network configuration. For some units, it doesn't work by pressing the SET button. To enter the AP mode, continuously press the LED button seven times in 10 seconds.

I Sense function (?)

The I Sense function enables the remote control to measure the temperature at its current location and send this signal to the air conditioner every 3 minutes interval. When using AUTO, COOL, or HEAT modes, measuring ambient temperature from the remote control (instead of from the indoor unit itself) will enable the air conditioner to optimize the temperature around you and ensure maximum comfort.

NOTE: Press and hold the 'I Sense' button for seven seconds to start/stop the memory feature of the I Sense function. For remote controls without an 'I Sense' button, press and hold the 'SLEEP' button for seven seconds to start/stop the memory feature of the I Sense function.

• If the memory feature is activated, "On" displays for 3 seconds on the screen.
• If the memory feature is stopped, "OF" displays for 3 seconds on the screen.
• While the memory feature is activated, pressing the ON/OFF button, shifting the mode, or power failure will not cancel the I Sense function.