Nightstand Assembly Instructions
Note: There is also a more detailed installation video on the product detail page on Amazon.
The assembled nightstand features a top surface with a built-in charging station (outlets and USB ports), an open shelf, and a drawer with a decorative rattan front. It stands on four angled wooden legs.
General Assembly Guidelines
- Ensure that all parts and hardware are available before beginning assembly.
- Follow each step carefully to ensure the proper assembly of this product.
- Two people are recommended for ease in the assembly of this product.
- The main type of hardware used to assemble this product is screws.
- Power tools should not be used to assemble this product.
- Please keep children and animals away from the work area, as swallowing small parts may cause suffocation.
Parts List
- Part 1: Top Panel with charging station cutout
- Part 2: Left Side Panel
- Part 3: Right Side Panel
- Part 4: Shelf
- Part 5: Bottom Panel
- Part 6: Drawer Back Panel
- Part 7: Drawer Bottom Panel
- Part 8: Legs (x4)
- Part 9: Drawer Front Panel
- Part 10: Drawer Left Side Panel
- Part 11: Drawer Right Side Panel
- Part 12: Drawer Bottom Support
- Part 13: Drawer Back Support
- Part 14: Charging Station Unit
Hardware List
- A x 8: Cam Lock Nuts
- B x 8: Cam Lock Bolts
- CR x 1: Drawer Slide Rail (Right)
- CL x 1: Drawer Slide Rail (Left)
- DR x 1: Drawer Slide Rail (Right)
- DL x 1: Drawer Slide Rail (Left)
- E x 12: Wooden Dowels
- F x 8: Screws (Ø5.5*48 mm)
- G x 1: Screw (m4*15 mm)
- H x 1: Drawer Knob
- I x 4: Leg Mounting Plates
- J x 4: Screws (Ø4*30 mm)
- K x 32: Screws (Ø3.5*12 mm)
- L x 4: Back Panel Brackets
- M x 4: Screws (Ø3*16 mm)
- N x 4: Leg Bottom Caps
- O x 1: Allen Wrench (M4 mm)
- P x 1: Screwdriver
The hardware quantities listed above are required for proper assembly. Some extra hardware may also have been included.
Step 1
Connect parts 10 and 11 to part 12 using screws J and screwdriver P.
Step 2
Insert part 13 into the notch of the assembly from Step 1. Install cam lock bolts B into part 9 using screwdriver P.
Step 3
Use screwdriver P to attach cam lock nuts A to the holes on part 9. Connect part 9 to the assembly from Step 2.
Step 4
Use screwdriver P and screws K to install drawer slide rails DR and DL into the assembly from Step 3.
Step 5
Use screwdriver P and screw G to install the drawer knob H into part 9.
Step 6
Use screwdriver P and screws K to attach drawer slide rails CL and CR to parts 2 and 3 respectively.
Step 7
Insert wooden dowels E into parts 4 and 5. Use Allen wrench O and screws F to connect part 3 to parts 4 and 5.
Step 8
Insert wooden dowels E into parts 4 and 5. Use screwdriver P and screws F to connect part 2 to parts 4 and 5.
Step 9
Insert parts 6 and 7 into the notch of the assembly from Step 8.
Step 10
Use screwdriver P and cam lock bolts B to attach the charging station unit (14) to the top panel (1).
Step 11
Insert wooden dowels E into the corresponding holes of part 9. Attach the top panel (1) to the assembly from Step 9 using cam lock nuts A and screwdriver P.
Step 12
Attach the leg mounting plates (I) to the bottom of the nightstand assembly using screws K and screwdriver P.
Step 13
Attach the legs (8) to the leg mounting plates (I) by screwing them in.
Step 14
Attach the leg bottom caps (N) to the bottom of the legs (8).
Step 15
Attach the charging station unit (14) to the top panel (1) using screws K and screwdriver P.
Step 16
Slide the assembled drawer (from previous steps) into the nightstand frame.
Step 17
Attach the back panel brackets (L) to the back panel of the nightstand using screws M and screwdriver P.
Step 18
Final Assembly: The nightstand is now fully assembled.
