VALBERG STEAMBOOST-05 Steam Station

Product Overview

Thank you for choosing this VALBERG product. VALBERG products are chosen, tested, and recommended by ELECTRO DEPOT, ensuring a top-quality, easy-to-use product. This device is designed to provide a pleasureable user experience.

Parts Identification

The steam station consists of the following parts:

• A Bottom
• B Water tank
• C Water tank handle
• D Iron lock
• E Iron lock release button
• F Thermal insulation stand
• G Upper cover
• H Display screen
• 1 Indicator: Automatic power failure prompt
• 2 Indicator: Energy Saving steam
• 3 Indicator: Big gear steam
• 4 Indicator: No water in the tank
• 5 Indicator: Clean tips
• I Cleaning button
• J SET Steam mode button
• K Power button
• L Handle
• M Rear cover
• N Cord guard
• O Steam button
• P Wire reel barrel
• Q Foot pad
• R Water pump damping silica gel

Specifications

Product Usage

Suggestions Before First Use

1. The iron may emit a little smoke on first use due to factory grease; this will cease shortly.
2. Remove any plastic protector from the soleplate and clean it with a soft cloth.
3. Avoid ironing over rough metal objects to prevent soleplate scratches.
4. Pure wool fibers (100% wool) can be ironed using the steam function. High steam setting and a dry ironing cloth are recommended.

Thermal Insulation Stand

• When not in use, lock the iron onto the thermal insulation stand (F) for safe storage and easy transport.
• To unlock, press the iron lock release button (E) and lift the iron.
• To lock, place the iron correctly on the stand and push the lock until it clicks.
• Note: The iron should be locked on the stand when not in use.

Using the Product

1. Press the power button (K) to turn the product on.
2. Press and hold the power button (K) for 2 seconds to turn it off.

Steady Temperature

1. Refer to garment care labels for ironing instructions.
2. The electronic temperature control adjusts heat automatically.

Filling the Water Tank

1. Disconnect the power supply.
2. Pull out the water tank (B).
3. Fill the tank to the MAX level through the water apertures.
4. Replace the water tank until it clicks into place on the thermal insulation stand.
5. Note: Use distilled or demineralized water if your local water is hard.

Steam Ironing

1. Fill the water tank as described above.
2. Plug the iron into a power outlet.
3. Steam ironing is only possible once the iron is hot. Otherwise, water may drip from the soleplate.
4. Wait for the indicator light (e.g., 1) to stop flickering, indicating the soleplate is hot.
5. Press the steam button (O) to begin steaming.
6. When finished, place the iron upright or on the stand.
7. Disconnect the iron from the power supply, empty any remaining water from the tank, and allow the iron to cool.

Continuous Steam

1. Once the iron is hot and the temperature is stable, press the steam mode button (J) to switch between Energy Saving steam (2) and Big gear steam (3).

Explosion Steam

1. When the iron is hot and stable, press the steam button (O) twice quickly within one second for a 2-second steam burst.

Auto Shut-off

1. The iron automatically powers off after 10 minutes of inactivity.
2. A power-off indicator will flash on the display, accompanied by six beeps.
3. Press the steam button (O) to resume operation.
4. The iron will not shut off during steam discharge.

Anti-drip

This iron features an anti-drip function that automatically stops steam emission when the temperature is too low, preventing water from dripping out of the soleplate.

Cleaning and Maintenance

Cleaning and Maintenance

1. Ensure there is sufficient water in the tank before cleaning.
2. The device will prompt for cleaning after 25 hours of pump operation.
3. Place the iron in a safe position before cleaning to prevent burns from hot water.
4. Once the iron is hot, press and hold the cleaning button (I) for 3 seconds to enter cleaning mode. The display will flash with 3 beeps.
5. After two minutes, a buzzer will sound three times to indicate cleaning is complete.

Troubleshooting

Storage

• Before storing the steam iron, ensure it has cooled down and is completely dry.
• Make sure the water tank is empty before storing.
• Fold the water supply hose in half, then wind it along the hose storage groove. Secure the power cord with a cable tie.
• Store the appliance in a cool, dry place.

Warranty Conditions

This product is guaranteed against faults caused by manufacturing defects or materials for a period of two years from the date of purchase. This warranty does not cover defects or damage caused by incorrect installation, improper use, or excessive wear and tear. Proof of purchase is required.