Manuals+

Bosch Dishwasher Quick Reference Guide

Model: SMS2ITI09E

Setting up Home Connect

Tip: Connect your appliance to a mobile device. You can conveniently change all settings using the Home Connect app.

1. Scan the following QR code: [QR Code for Home Connect]

You can install the Home Connect app and connect your appliance via the QR code.

2. Follow the instructions in the Home Connect app.

Water Hardness Settings

You can find an overview of the water hardness values that can be selected here. A table of country-specific units can be found in the instruction manual.

Hardness mmol/l range Setting value Hardness range mmol/l Setting value
SoftH00Soft0-1.1H00
MediumH01Medium1.2-1.4H01
MediumH02Medium1.5-1.8H02
MediumH03Medium1.9-2.1H03
MediumH04Medium2.2-2.9H04
HardH05Hard3.0-3.7H05
HardH06Hard3.8-5.4H06
HardH07Hard5.5-8.9H07

Setting the Water Softening System

1. Press the [Setup button].

2. To open the basic settings, press the [Setup button] for 3 seconds. The display shows Hxx. The display shows 'set'.

3. Press the [Start button] repeatedly until the right water hardness has been set.

4. To save the settings, press the [Setup button] for 3 seconds.

Adding Special Salt

To avoid damage to the appliance, only add special salt to the dispenser for special salt just before the programme starts.

1. Unscrew the lid of the dispenser for special salt and remove it. [Diagram: Hand unscrewing lid of salt dispenser]

2. On initial start-up: Fill the dispenser right up with water. [Diagram: Filling salt dispenser with water]

3. Add the special salt to the dispenser. The water in the dispenser is displaced and forced out. Never add detergent. [Diagram: Adding salt granules to dispenser]

4. Place the lid back on the dispenser and turn to close.

Adding Rinse Aid

1. Press the catch on the lid of the dispenser for rinse aid and lift it. [Diagram: Hand pressing catch and lifting lid of rinse aid dispenser]

2. Add rinse aid up to the max mark. [Diagram: Pouring rinse aid into dispenser up to MAX line]

3. Close the lid of the dispenser for rinse aid. The lid clicks into position. [Diagram: Closing rinse aid dispenser lid]

Adding Detergent

1. Add the detergent to the dry detergent dispenser. [Diagram: Adding detergent powder/liquid to detergent dispenser]

2. Close the lid of the detergent dispenser. The lid clicks into position. [Diagram: Closing detergent dispenser lid]

Programmes

The programme data has been measured in the laboratory according to European standard EN 60436. The consumption figures are guide values (except Eco) and depend on the programme and additional function selected. The running time will change if the rinse aid system is switched off or rinse aid needs to be added.

Programme 1) Duration [h:min] 2) Energy consumption [kWh] 3) Water [l]
Intensive 70°2:10 - 2:151.350 - 1.40010.5-13.5
Auto 45-65°1:45 - 2:450.850-1.2509.5-15.5
Eco 50°4:100.9379.5
Express 65° - 1h1:001.20010.0
Machine Care2:101.45015.0
Favourite0:15 - 0:150.050 -0.0504.0-4.0

How to Use Your Appliance

1. Load the tableware. Only clean tableware that is suitable for dishwashers. Remove large remnants of food from the tableware. Check that the spray arms can rotate freely. [Diagram: Loading dishwasher racks with tableware]

2. Add detergent. [Diagram: Adding detergent to dispenser]

3. Switch on the appliance. [Diagram: Power button on dishwasher]

4. Select the programme. [Diagram: Programme selection dial/buttons]

5. Start the programme. [Diagram: Start button on dishwasher]

6. Remove the tableware at the end of the programme.

7. To cancel the programme, press the [Reset button] for approx. 4 seconds. The programme is cancelled and ends after approx. 1 minute.

Cleaning Filters

1. After each wash check the filters for residue.

2. Turn the coarse filter anticlockwise and remove the filter system. [Diagram: Turning and removing coarse filter]

3. Pull down the micro filter to remove. [Diagram: Pulling down micro filter]

4. Press the locking catches together and lift the coarse filter out. [Diagram: Pressing catches and lifting coarse filter]

5. Clean the filter elements under running water.

6. Re-assemble the filter system.

7. Insert the filter system into the appliance and turn the coarse filter clockwise. Make sure that the arrow markings match up. [Diagram: Re-inserting filter system and turning coarse filter clockwise]

8. Install the filter system.

Cleaning Spray Arms

1. Unscrew the upper spray arm and pull down to remove. [Diagram: Unscrewing and removing upper spray arm]

2. Pull up the lower spray arm to remove. [Diagram: Pulling up lower spray arm]

3. Check the outlet nozzles on the spray arms for blockages under running water and remove any foreign objects.

4. Insert the lower spray arm. The spray arm clicks into position. [Diagram: Inserting lower spray arm]

5. Insert the upper spray arm and screw it firmly in place. [Diagram: Screwing in upper spray arm]

Clean Wastewater Pump

1. Disconnect the appliance from the power supply.

2. Remove the filter system.

3. Scoop out any water.

4. Prise off the pump cover using a spoon and grip it by the crosspiece. [Diagram: Using spoon to pry off pump cover]

5. Lift the pump cover inwards at an angle and remove. [Diagram: Removing pump cover]

6. Remove any remnants of food and foreign bodies in the area of the impeller.

7. Insert the pump cover and press down. The pump cover clicks into position. [Diagram: Re-inserting and pressing pump cover]

8. Install the filter system.

Troubleshooting

Fault Cause and troubleshooting
E:32-00 will light up alternately or indicator for water supply lights up.
  • Supply hose is kinked. Install the supply hose without kinks.
  • Water tap is turned off. Turn on the water tap.
  • Water tap is jammed or furred up. Turn on the water tap. The flow rate must be at least 10 l/min when the water supply is open.
  • The filters in the water connection of the supply or AquaStop hose are blocked.
    1. Switch off the appliance.
    2. Pull out the mains plug.
    3. Turn off the water tap.
    4. Unscrew the water connection.
    5. Remove the filter from the supply hose. [Diagram: Removing filter from supply hose]
    6. Clean the filter.
    7. Re-insert the filter in the supply hose.
    8. Screw the water connection back on.
    9. Check the water connection for leaks.
    10. Restore the power supply.
    11. Switch the appliance on.
E:61-02 will light up alternately.
  • Wastewater pump is blocked. Clean the wastewater pump.
  • Cover of the wastewater pump is loose. Secure the cover of the Wastewater pump so it clicks into position.
E:92-40 will light up alternately.
  • Filters are soiled or blocked. Clean the filters.
  • Tableware is placed too close together or basket is overfilled.
    1. Arrange tableware with sufficient space in between. The spray jets must reach the surfaces of the tableware.
    2. Avoid points of contact.
  • Spray arm rotation is blocked. Arrange tableware so that it does not obstruct spray arm rotation.
  • Spray arm nozzles are blocked. Clean the Spray arms.
  • Filters are soiled. Clean the filters.
  • Filters are inserted incorrectly and/or not engaged.
    1. Insert the filters properly.
    2. Engage the filters.
  • Washing programme selected too weak. Select a more intensive washing programme.
Remnants of food on tableware.
  • Tableware is placed too close together or basket is overfilled.
    1. Arrange tableware with sufficient space in between. The spray jets must reach the surfaces of the tableware.
    2. Avoid points of contact.
  • Spray arm rotation is blocked. Arrange tableware so that it does not obstruct spray arm rotation.
  • Spray arm nozzles are blocked. Clean the Spray arms.
  • Filters are soiled. Clean the filters.
  • Filters are inserted incorrectly and/or not engaged.
    1. Insert the filters properly.
    2. Engage the filters.
  • Washing programme selected too weak. Select a more intensive washing programme.
Removable streaks are present on glasses, glassware with a metallic appearance and cutlery.
  • Amount of rinse aid to be dispensed is set too high. Set the rinse aid system to a lower setting.
  • No rinse aid has been added. Add rinse aid.
Rust spots on cutlery.
  • Cutlery is not sufficiently rust-resistant. Knife blades are often more severely affected. Use rust-resistant tableware. Cutlery may also rust if washed together with rusting items. Do not wash rusting items.
Detergent residue is present in the detergent dispenser or the tablet collecting tray.
  • Spray arms were blocked by tableware so detergent was not rinsed out. Check that the spray arms are not blocked and can rotate freely.
All LEDs light up or flash or the rinse programme does not continue running.
  • Electronics have detected a fault. Press the main switch button for approx. 4 seconds. The appliance is reset and restarted.
Models: SMS2ITI09E, SMS2ITI09E Dishwasher, SMS2ITI09E, Dishwasher

PDF preview unavailable. Download the PDF instead.

9001995443 B ST4 PDF Engine (Build 12.0.4.0)

Related Documents

Preview Bosch SMS2ITI04Y Dishwasher Quick Reference Guide
A quick reference guide for the Bosch SMS2ITI04Y dishwasher, covering setup, operation, cleaning, and troubleshooting.
Preview Bosch SMI4HBS19E Dishwasher Quick Reference Guide
A quick reference guide for the Bosch SMI4HBS19E dishwasher, covering setup, operation, cleaning, and troubleshooting. Learn how to connect to Home Connect, manage water hardness, add detergent and rinse aid, select programmes, and maintain your appliance.
Preview Bosch SPH4EKX24E Dishwasher Quick Reference Guide
A concise guide to setting up, operating, and maintaining your Bosch SPH4EKX24E dishwasher, including water hardness settings, program details, cleaning instructions, and troubleshooting.
Preview Bosch SMS4HTW03E Dishwasher Quick Reference Guide
Concise guide for Bosch SMS4HTW03E dishwasher users, covering Home Connect setup, water hardness settings, programme selection, loading tips, cleaning procedures for filters, spray arms, and wastewater pump, and troubleshooting common faults. Essential information for optimal appliance use.
Preview Bosch Dishwasher SMS4ETI14E Quick Reference Guide
A concise guide for setting up, using, and maintaining the Bosch Dishwasher SMS4ETI14E, covering Home Connect setup, water hardness, programmes, cleaning, and troubleshooting.
Preview Bosch SPS4EMW61E Dishwasher Quick Reference Guide
A quick reference guide for the Bosch SPS4EMW61E dishwasher, covering setup, operation, cleaning, and troubleshooting steps.
Preview Bosch Dishwasher Quick Reference Guide: Setup, Programmes, and Troubleshooting
A concise guide for Bosch dishwashers, covering initial setup, Home Connect, water hardness settings, programmes, usage, cleaning, and troubleshooting common faults.
Preview Bosch SMS4HVI14E Dishwasher: Quick Reference Guide & Setup
Concise guide for setting up and using your Bosch SMS4HVI14E dishwasher, including Home Connect setup, water hardness, programmes, cleaning, and troubleshooting.