User Guide for BOSCH models including: SMS2ITI04Y, SMS2ITI04Y Dishwasher, Dishwasher
en Before using for the first time, read the instruction manual and the safety information it contains. Setting up Home Connect.
19 ore fa — en Before using for the first time, read the instruction manual and the safety information it contains. Setting up Home Connect.
*9001827584*. Quick reference guide Dishwasher en Before using for the first time, read the instruction manual and the safety information it contains.
Quick reference guideDishwasher en Before using for the first time, read the instruction manual and the safety information it contains. Setting up Home Connect Tip: Connect your appliance to a mobile device. You can conveniently change all settings using the Home Connect app. 1. Install the Home Connect app on your mo- bile device and follow the instructions. 2. Scan the QR code with the Home Connect app. Overview of water hardness settings You can find an overview of the water hardness values that can be selected here. A table of country-specific units can be found in the instruction manual. Hardness range Soft Medium Hard Hard mmol/l 0 - 1.1 1.2 - 2.9 3.0 - 3.7 3.8 - 6.2 Level 0 1 2 3 LED A LED B LED C Setting the water softening system 1. Press . 2. To open the appliance settings, press for 3 seconds. a flashes. 3. Press repeatedly until the right water hardness has been set. 0, 1, 2 or 3 LEDs will light up ac- cordingly. 4. To save the settings, press for 3 seconds. Adding special salt To avoid damage to the appliance, only add special salt to the dispenser for special salt just before the programme starts. 1. Unscrew the lid of the dispenser for special salt and remove. 2. On initial start-up: Fill the dispenser right up with water. 3. Add the special salt to the dispenser. The water in the dispenser is displaced and forced out. Never add detergent. 4. Place the lid back on the dispenser and turn to close. Adding rinse aid Programmes The programme data has been measured in the laboratory according to European standard EN 60436. The consumption figures depend on the programme and additional function selected. The running time will change if the rinse aid system is switched off or rinse aid needs to be added. Programme Intensive 70° Auto 45-65° Eco 50° Express 65° - 1h Machine Care Favourite 1) Duration [h:min] 2) Energy [kWh] 3) Water [l] 1) 2:10 - 2:15 2) 1.300 - 1.350 3) 11.0 - 13.5 1) 1:45 - 2:45 2) 0.850 - 1.350 3) 9.5 - 15.5 1) 4:30 2) 0.923 3) 10.5 1) 1:00 2) 1.100 3) 10.0 1) 2:10 2) 1.450 3) 15.0 1) 0:15 - 0:15 2) 0.050 - 0.050 3) 4.0 - 4.0 1. Press the catch on the lid of the dispenser for rinse aid and lift . 2. Add rinse aid up to the 2 max mark. max 1 3. Close the lid of the dispenser for rinse aid. a The lid clicks into position. Adding detergent 1. Add the detergent to the dry detergent dispenser. 50 ml 25 ml 2. Close the lid of the detergent dispenser. 15 ml a The lid clicks into position. 9001827584(030131)SMS2ITI04Y *9001827584* How to use your appliance 1. Load the tableware. tate freely. Only clean tableware that is suitable for dish- 2. Add detergent. washers. Remove large remnants of food from 3. Switch on the appliance . the tableware. Check that the spray arms can ro- 4. Select the programme. 5. Start the programme . 6. Remove the tableware at the end of the pro- gramme. 7. To cancel the programme, press for approx. 4 seconds. The programme is cancelled and ends after ap- prox. 1 minute. Cleaning filters 1. After each wash check the filters for residue. 2. Turn the coarse filter anticlock- 2 wise and re- move the filter system . 1 3. Pull down the micro filter to remove. 4. Press the locking catches to- gether and lift 1 the coarse filter out . Cleaning spray arms 1. Unscrew the upper spray arm and 2 pull down to remove . 1 2 5. Clean the filter elements under running water. 6. Re-assemble the filter system. 7. Insert the filter system into the appliance and turn the coarse filter clockwise. Make sure that the arrow markings match up. 2. Pull up the lower spray arm to remove. 3. Check the outlet nozzles on the spray arms for blockages under running water and remove any foreign bodies. 4. Insert the lower spray arm. a The spray arm clicks into position. 5. Insert the upper spray arm and screw it firmly in place. Clean wastewater pump 1. Disconnect the appliance from the power supply. 2. Remove the filter system. 3. Scoop out any water. 4. Prise off the pump cover using a spoon and grip it by the crosspiece. 5. Lift the pump cover inwards at an angle and remove. 6. Remove any remnants of food and foreign bodies in the area of the impeller. 7. Insert the pump cover and press down . 2 a The pump cover clicks into position. 1 8. Install the filter system. Troubleshooting Fault Remnants of food on tableware. Cause and troubleshooting Tableware is placed too close together or basket is overfilled. 1. Arrange tableware with sufficient space in between. The spray jets must reach the surfaces of the tableware. 2. Avoid points of contact. Spray arm rotation is blocked. Arrange tableware so that it does not obstruct spray arm ro- tation. Spray arm nozzles are blocked. Clean the Spray arms. Filters are soiled. Clean the filters. Fault Cause and troubleshooting Remnants of food on tableware. Filters are inserted incorrectly and/or not engaged. 1. Insert the filters properly. 2. Engage the filters. Washing programme selected too weak. Select a more intensive washing programme. Removable streaks are Amount of rinse aid to be dispensed is set too high. present on glasses, glass- Set the rinse aid system to a lower setting. ware with a metallic appearance and cutlery. No rinse aid has been added. Add rinse aid. Rust spots on cutlery. Cutlery is not sufficiently rust-resistant. Knife blades are often more severely affected. Use rust-resistant tableware. Fault Rust spots on cutlery. Detergent residue is present in the detergent dispenser or the tablet collecting tray. All LEDs light up or flash or the rinse programme does not continue running. Cause and troubleshooting Cutlery may also rust if washed together with rusting items. Do not wash rusting items. Spray arms were blocked by tableware so detergent was not rinsed out. Check that the spray arms are not blocked and can rotate freely. Electronics have detected a fault. Press the main switch button for approx. 4 seconds. The appliance is reset and restarted.ST4 PDF Engine (Build 12.0.1.0)