Lockly Vision™ Elite Installation Guide - Deadbolt Edition

Getting Started

For the latest version of this installation guide, visit Lockly.com/installation.

Alternatively, scan the QR code on your phone to watch step-by-step video installation.

Welcome!

This guide will walk you through the step-by-step process to install and get your Lockly Vision™ Elite up and running. Installation typically takes less than 30 minutes. For any questions, please refer to our online support at Lockly.com/support or call (669) 500-8835 for assistance.

A foldout overview of installation parts is available on the back page.

Preparation

Tools Required:

• Phillips Screwdriver
• Flathead Screwdriver
• Tape measure or ruler

Important Notes:

Door Preparation:

Prepare your door by removing the existing deadbolt or using the provided template to bore new holes. Ensure the door's cross-bore is 2-1/8" (54mm) and the backset is either 2-3/8" (60mm) or 2-3/4" (70mm). The edge bore should be 1" (25mm).

REPLACE YOUR EXISTING OLD DEADBOLT. USE THE INCLUDED DEADBOLT DESIGNED AND OPTIMIZED FOR LOCKLY SMART LOCKS. The integrated deadbolt includes a smart door sensor to detect the open/closed status of your door. You may need to increase the depth of the groove depending on the gap between the door and door frame.

Step 1: Adjust Deadbolt and Install

The deadbolt defaults to a 2-3/4" (70mm) backset. If the deadbolt slot is aligned with the center of the door hole, you can skip the following adjustment steps.

To adjust the deadbolt to a 2-3/8" (60mm) backset:

• Hold the metal plate (C) and twist the deadbolt body (D) clockwise until it snaps into the 2-3/8" (60mm) position.
• To return to the default 2-3/4" (70mm) setting, hold the metal plate (C) and twist the deadbolt body (D) counter-clockwise until it snaps into place.

Extend the deadbolt by inserting a flat-head screwdriver into the slot and turning clockwise.

Insert the extended deadbolt into the door edge. Ensure the right side is up and the slot is vertical. Secure it with two (2) K screws.

Observe the cable's position to ensure it aligns with your door's opening orientation (Left/Right Swing) and the Backset size (60mm/70mm).

Step 2: Installing Exterior Assembly (B)

1. Peel off the protective film from the adhesive strips (E).
2. Ensure the torque blade is in a vertical position with the deadbolt extended.
3. Guide the cable through under the deadbolt by gently pulling it from the inside, ensuring it remains straight and not bent. Mount the exterior assembly by aligning it securely with the exterior surface of the door and ensuring it is flush.

Step 3: Installing Interior Assembly (G)

1. Peel off the protective film from the adhesive strips on the back of the mounting plate (D). Guide connection cables through the hole and secure to the notch on the lower left corner. Align the mounting plate onto the door and firmly press to secure it in place.
2. Insert and hand-tighten two (2) F screws on the left and right of the blade. Check alignment and insert screws through the circular holes on both sides of the deadbolt torque blade, aligning them with the screw holes on the exterior assembly. Ensure screws do not compress or damage the cable, then tighten with a screwdriver until the mounting plate is securely attached to the door.
   ? QUICK TIP: When installing screws by hand, turn them clockwise several turns, then counterclockwise one turn to ensure smooth threading and prevent cross-threading.
3. Use the key to ensure the deadbolt locks and unlocks smoothly. Rapid beeping indicates an issue, such as misalignment or excessive rubbing/binding.

4. Plug the cables coming through mounting plate (D) into the interior assembly (G) as shown, routing them to the right of the interior assembly (G).

Connect A1 to A2, B1 to B2, C1 to C2, and D1 to D2 as illustrated.

For assistance if pins are not centered or bent, call Customer Care at (669) 500-8835.

5. Insert the connected cables (C1+C2) and (D1+D2) into the grooves on the side. Ensure the foam pads attached to the cables are secured to prevent movement.

Tuck the cables behind the cable rail of the interior assembly.

Hold the cables together to prevent movement and prepare for mounting onto the door.

6. Before placing the interior assembly onto the mounting plate, ensure the thumb turn is vertical.

7. Place the interior assembly against the mounting plate, ensuring the torque blade is inserted into the thumb turn shaft.

8. Secure the interior assembly to the mounting plate with two (2) H screws.

Torque Blade & Thumb Turn Shaft Alignment: Ensure both are in the vertical position.

Step 4: Installing Battery

1. With the door open and deadbolt fully extended, insert the lithium battery. Secure it on the provided slot of the interior assembly. (Optional) Tighten the screw on the right side.
   ❗ IMPORTANT: If this is your first time using the battery, ensure it has been fully charged using any standard 5V USB charger.
2. After securing the battery, use the pin key from the accessory bag to HOLD the program button for 10 seconds. The lock will start a self-check. Release the button once the check begins. This process determines the door swing direction and is crucial for correct installation.
   ❗ IMPORTANT: If the lock is not properly installed, it will open and close repeatedly.
3. Once the self-check completes, ensure the lock operates smoothly by manually locking and unlocking the door using the thumb turn. The deadbolt should operate without interference or binding. If issues occur, repeat step 2, ensuring (a) the deadbolt was extended and (b) the torque blade was inserted vertically.
4. Swipe your hand across the touchscreen. The lock should close (lock). If the touchscreen is ON, touch the lock icon [?], and the lock should also engage. If the deadbolt bounces back or unlocks automatically, it indicates an incorrect installation. Go back and repeat step 2.

Step 5: Installing Strike Plate

Use the supplied door strike plate (L), which includes a built-in door sensor magnet.

If your door gap is larger than 5mm, it is recommended to install the Strike Spacer (P) to reduce the gap and ensure proper operation of the door sensor.

USE THE INCLUDED DOOR STRIKE PLATE WITH INTEGRATED DOOR SENSOR. Depending on your door and door frame gap, you may need to increase the groove depth or use a strike spacer.

When installing the deadbolt and door strike, ensure the two red marks are aligned.

Side View (70mm)

Side View (60mm)

Step 6: Setup the Hub

To enable video doorbell, live monitoring, and voice control with Hey Google and Alexa, you need to set up the included Vision Connect Wi-Fi hub with your Lockly Vision™ Elite smart lock + video doorbell.

Hub Components: Antenna, LED status lights, LAN cable, Power adapter, TF card.

Step 7: Lockly App & Unique Activation Code

Before setting up the Vision Connect Hub, download the Lockly app on your smartphone. This is required to complete the connection setup between the hub and the lock.

Scan the QR code, visit the app store, or go to Lockly.com/app.

You will also need the Activation Card with a unique pre-paired QR code for your lock. This card is in the packaging. The QR code can also be found at the bottom of the Vision Connect Hub. Keep it in a safe place, as it is required for setup and for resetting your smartphone or access code.

Step 8: Location Guidelines

The Vision Connect Hub connects directly to your Wi-Fi router via the provided LAN cable. Choose an appropriate location for optimal performance. For best connectivity, set up the hub LESS than 100 feet (30 meters) away from the lock and elevated at least 3 feet (1 meter) off the ground.

During setup, position yourself between the lock and the Vision Connect hub, ideally no more than 100 feet (30 meters) apart. Ensure your iOS or Android™ device has both Bluetooth® and Wi-Fi enabled.

Step 9: Vision Connect Hub Setup

Ensure the TF card included with Vision Connect is properly inserted.

Connect the LAN cable to the closest Wi-Fi router to the Lockly Vision™ Elite lock (within 100ft). Always keep the Antenna in the UP position.

Connect the power cable and plug the USB power adapter into an outlet.

Wait 2 minutes for the hub to self-calibrate. The LEDs will turn RED and blink yellow.

Vision Connect is now ready to connect to your iOS or Android™ device. Refer to the troubleshooting section if LEDs do not meet the described conditions.

Step 10: Pair Vision Lock to App

Launch the Lockly App and select "add a new device", then select "Vision". You will be prompted to scan the QR code from the Activation Card or the Vision Connect Hub.

Vision Connect Status & Troubleshooting

During Setup:

• Solid red ON: After connecting LAN cable and power adapter, wait 2 minutes for Vision Connect to self-calibrate. Status: Power ON / Successfully paired.
• Yellow slow blinking: Status: Network connected.
• Red slow blinking: Status: Pairing / Network NOT yet connected.
• Red fast blinking: Status: Pairing unsuccessful.
• Yellow OFF: Status: Router or LAN cable issue, NO network connection.
• Blinking red goes to blue, then turns OFF: Status: Resetting.

During Firmware Update:

• Blue slow blinking: Status: Update in progress*.
• Blue ON: Status: Update Successful.
• Blinking from red to blue: Status: Update has failed.

*Power interruption during firmware update may damage the Vision Connect hub. Do not interrupt or turn the power off while firmware update is in progress.

Smart Home Ready - Voice Control

Hands-free voice control: Control and check your status using only your voice with Amazon Alexa or Google Assistant-enabled devices.

Example: "Alexa, is my Front Door locked?" Response: "Your Front Door is locked."

To set up voice control, download the Amazon Alexa or Google Home App and add the "Lockly" skill for Alexa or "Lockly Action" on Google.

In the Google Home or Amazon Alexa app, add the Lockly skill/action and follow the on-screen instructions. For a full list of commands, help videos, or troubleshooting, visit Lockly.com/help.

Google, Android, Google Play and Google Home are trademarks of Google LLC.

FCC Warning

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. It should be installed and operated with a minimum distance of 20cm between the radiator and your body.

IC WARNING

This device contains licence-exempt transmitter(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

IC Radiation Exposure Statement: This equipment meets the exemption from the routine evaluation limits in section 2.5 of RSS-102. It should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.

French Compliance Statement: L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: 1. L'appareil ne doit pas produire de brouillage; 2. L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Cet équipement est conforme à l'exemption des limites d'évaluation habituelle de la section 2.5 de la norme RSS-102. Il doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et toute partie de votre corps.

California Proposition 65 Warning

WARNING: This product can expose you to chemicals including Lead, which is known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov.

Installation Overview and Parts List

The Lockly Vision™ Elite can be fitted for both right swing doors and left swing doors.

Parts List:

Support and Resources

We're here to help! Email: help@Lockly.com

For the most up-to-date version of this guide, please visit: Lockly.com/help

© Copyright 2023 Lockly All rights reserved.

Patent information available.

Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. Other trademarks and trade names are those of their respective owners. Google, Android, Google Play and Google Home are trademarks of Google LLC. Amazon.com, Inc. and its affiliates.