Ambius Security and Sensor Lights

Product Overview

The Ambius Security and Sensor Lights are designed for reliable outdoor illumination and security. They feature adjustable heads, selectable color temperatures, and adjustable detection range and duration.

IP55 rated, constructed from Polycarbonate (PC) material.

Light Specifications

• Power: 16W (2x 8W)
• Color Temperature/Lumens: 3000K - 1300LM / 4000K - 1500LM / 5700K - 1400LM
• Non Dimmable
• Power/Lumen Adjustable
• Beam Angle: 90°
• Detection Range: 6-8 meters
• Detection Angle: 150°
• LUX Adjustment: 3, 30, 300, 2000 LUX
• Time Adjustment: 10 seconds to 15 minutes
• Manual Override Function available
• Base: Easy mount base plate
• Material: Polycarbonate (PC)
• Estimated Life: LM80 35,000 hours
• Power Supply: 220-240V 50/60Hz

Fully Adjustable Heads

Each light head can be independently adjusted for rotation and tilt to achieve optimal light performance where required.

[Description: Diagram showing two adjustable LED light heads on a base, with arrows indicating tilt and rotation adjustment.]

Mounting Options

The lights can be mounted on a wall or a ceiling.

[Description: Diagram illustrating a wall mount configuration and a ceiling mount configuration.]

Time Adjustment

The duration the light stays on after motion is detected can be adjusted from 10 seconds to 15 minutes. Approximate positions for 5 and 9 minute settings are indicated.

[Description: Diagram of a dial labeled "TIME ADJUSTMENT" with markings for 10 sec, 5 min, 9 min, 15 min, and a pointer.]

LUX Adjustment

This setting determines the ambient light level at which the sensor activates.

• To operate in daylight, position the dial at the [plus symbol] mark.
• To operate only at night, position the dial at the [moon symbol] mark (approximately 3 lux).
• The other two positions are for low light conditions, indicated as approximately 30 lux and 300 lux.

[Description: Diagram of a dial labeled "LUX ADJUSTMENT" with markings for a sun symbol (daylight), a moon symbol (night/3 lux), and intermediate positions for 30 lux and 300 lux.]

Color Temperature Selection

Choose your desired color temperature by moving the switch to either 3000K, 4000K, or 5700K.

[Description: Diagram showing three color temperature options: 3000K, 4000K, 5700K.]

Installation

1. Ensure the power is turned off before installation.
2. Unscrew the retention screws on the front of the unit and remove the base plate.
3. Feed the power cable through the aperture provided in the base plate.
4. For Vertical Installation, ensure the arrow on the base plate points upwards.
5. For Horizontal Installation, ensure the arrow on the base plate points opposite to the sensor/lights.
6. Fix the base plate securely to the wall or ceiling using the provided screw holes.
7. Connect the power source wires: Neutral (N) to the blue wire, and Live (L) to the brown wire, following the wiring diagram.
8. Plug the light unit back into the base by aligning the arrow on the light with the arrow on the base and ensuring the 3-Pin terminals connect correctly. Refer to Fig 1.
9. Turn on the power.

[Description: Fig 1 shows a 3-pin connection terminal block with 'UP' indicators for correct alignment during installation.]

Testing

To test the sensor's functionality:

• Set the TIME dial to the [minus symbol] (shortest duration) and the LUX dial to the [sun symbol] (daylight/maximum sensitivity).
• After approximately 30 seconds, the sensor should detect presence, turn the light on, and then turn off after the set time (10 seconds in this test).
• To simulate nighttime conditions for testing during the day, turn the LUX dial towards the [moon symbol] and cover the sensor face with your hand to simulate darkness.

Manual Override Function

This function allows the light to stay ON for extended periods.

1. With the light in PIR mode and currently ON, turn the power OFF and then ON again within 3 seconds. Wait at least 1 second between each power cycle to ensure the sensor fully shuts off.
2. Perform this OFF/ON sequence twice.
3. A single flash from the spotlights indicates the unit has entered Manual Override Mode, and the light will remain ON.
4. To return the sensor to PIR mode, turn the power OFF, wait 10 seconds, and then turn the power ON. The light will automatically revert to PIR mode.

Care and Cleaning

Wipe the exterior of the light with a damp cloth. Do not immerse the unit in water.

Proof of Purchase

Please retain your purchase receipt for all warranty claims.

Warranty

This product is warranted against manufacturing faults for a period of 3 years when used in normal domestic conditions. CDB Group will replace the product free of charge if found to be defective due to a manufacturing fault during the warranty period. This warranty excludes damage caused by misuse, neglect, shipping accidents, incorrect installation, or unauthorized repairs. For warranty service, return the product to the retailer with proof of purchase. In New Zealand, the product is also covered by the Consumers Guarantee Act (1993).

Contact Information

CDB GROUP

New Zealand
PO Box 100-707
N.S.M.C
Auckland 0745
Phone: +64 (0)9 917 4000
Phone: 0800 232 633
Email: info@cdb.co.nz

Australia
PO Box 574
South Morang
Victoria, 3752
Phone: +61 (0)3 9336 4423
Phone: 1300 465 324
Email: info@cdbgoldair.com.au