1. Download Instructions
Use the link www.conrad.com/downloads (or scan the QR code) to download the complete operating instructions (or new/current versions if available). Follow the instructions on the web page.
2. Intended Use
This product is a wireless remote controller set for industrial applications. It is intended for controlling construction machinery and industrial equipment such as cranes and conveyors. The product has an IP65 ingress protection rating, protecting it against dust and low-pressure water jets from any direction. Do not submerge the product in water. The product is suitable for outdoor use. Using the product for purposes other than those described may damage it. Improper use can lead to short circuits, fires, or other hazards. The product complies with statutory national and European regulations. For safety and approval reasons, do not modify or alter this product. Read the operating instructions carefully and store them safely. Only pass the product on to third parties together with the operating instructions. All company names and product names are trademarks of their respective owners. All rights reserved.
3. Delivery Content
- Remote control (transmitter)
- Receiver
- Strap for transmitter
- 2x battery packs
- Receiver mounting material
- 4x rubber mounting bushings
- 4x (nuts, bolts, washer, spring washer)
- 2x spare fuses (10 A)
- Power adaptor
- Antenna base for receiver
- Antenna
- Operating instructions
4. Description of Symbols
- ⚠️ This symbol warns of hazards that can lead to personal injury.
- ⚡ This symbol warns of dangerous voltage that can lead to personal injury by electric shock.
- ℹ️ Read the operating instructions carefully.
5. Safety Instructions
5.1 General Information
- The product is not a toy. Keep it out of the reach of children and pets.
- Do not leave packaging material unattended.
- Contact technical support for unanswered questions.
- Maintenance and repairs must be performed by qualified personnel only.
5.2 Handling
- Handle the product carefully. Avoid shocks and falls.
5.3 Operating Environment
- Avoid mechanical stress, extreme temperatures, flammable gases, steam, solvents, and direct sunlight.
5.4 Operation
- Consult an expert if you have doubts about operation, safety, or connection.
- If the product is no longer safe to operate, take it out of service and protect it from accidental use. Do not attempt self-repair.
5.5 Power Adapter
- Do not modify or repair the power adapter or its components. Use only the supplied adapter.
- Connect to an accessible wall socket. Check voltage compatibility.
- Avoid wet hands when connecting/disconnecting.
- Unplug by the grip, not the cable. Disconnect during storms.
- Handle damaged adapters with extreme caution; switch off power first before touching.
5.6 LiPo Battery
- Do not damage the battery casing (risk of explosion/fire).
- Avoid short-circuiting battery contacts. Do not incinerate the battery or product.
- Charge regularly, even when not in use.
- Never leave the battery unattended while charging.
- Place the product on a heat-resistant surface during charging.
5.7 Connected Devices
- Observe the safety and operating instructions of connected devices.
6. Battery
6.1 Inserting/Removing (Remote Control)
- Inserting: Align the notch on the battery (top right) and press it into the battery compartment until it clicks.
- Removing: Pull the battery out by the notch. Use a flat screwdriver as a lever if necessary.
6.2 Charging
- Use only the supplied charger.
- Connect the charger to the battery, then to the mains power supply.
- LED Indicator: Red = Charging, Green = Fully charged.
7. Mounting and Connection
7.1 Antenna
- Important: Do not place the antenna in shielded areas. The antenna has a magnetic foot for secure mounting.
- Position the antenna for an interference-free connection to the remote control during operation.
- Connect the antenna cable to the receiver, place the antenna foot, and connect the antenna to the foot.
7.2 Receiver Mounting
- Ensure the antenna position provides a good connection.
- Ensure all receiver wires are connected properly and without tension.
- Mount the receiver using the provided brackets and rubber spacers onto a suitable surface.
7.3 Receiver Wiring
Note: Wire numbers are on the sheaths. Connect wires according to the overview.
| Description | Wire Number | Description | Wire Number | Description | Wire Number |
|---|---|---|---|---|---|
| F1 0.5A Power supply 1 | 1 | F2 10A COM 1 | 3 | F5 10A COM 3 | 19 |
| Power supply 2 | 2 | MAIN / E-STOP | 4 | Main Hook Down 1 | 20 |
| RO | 5 | Main Hook Up 1 | 21 | ||
| F3 10A COM 2 | 6 | Main Hook D/U 2 | 22 | ||
| Trolley Forward 1 | 7 | Trolley Backward 1 | 8 | Main Hook D/U 3 | 23 |
| Trolley F/B 2 | 9 | Main Hook D/U 4 | 24 | ||
| Trolley F/B 3 | 10 | Main Hook D/U 5 | 25 | ||
| Trolley F/B 4 | 11 | Auxiliary Hook Down 1 | 26 | ||
| Trolley F/B 5 | 12 | Auxiliary Hook Up 1 | 27 | ||
| Cart Left 1 | 13 | Auxiliary Hook D/U 2 | 28 | ||
| Cart Right 1 | 14 | Auxiliary Hook D/U 3 | 29 | ||
| Cart L/R 2 | 15 | Auxiliary Hook D/U 4 | 30 | ||
| Cart L/R 3 | 16 | Auxiliary Hook D/U 5 | 31 | ||
| Cart L/R 4 | 17 | F5 10A COM 4 | 32 | ||
| Cart L/R 5 | 18 | AUX 1 | 33 | ||
| C | 34 | ||||
| A | 35 | ||||
| B | 36 | ||||
| D | 37 | ||||
| AUX 2 | 38 | ||||
| AUX 3 | 39 | ||||
| AUX 4 | 40 |
8. Remote Control
8.1 Component Identification
- Left Side: 1. Emergency Stop Button, 2. AUX 1, 3. C/OFF, 4. A-OFF-B, 5. D/OFF, 6. AUX 2.
- Right Side: 7. ON/OFF Rotary Switch, 8. Transmission Enabling Button.
- Top/Center: 14. Left Joystick (8 directions, 5 speed levels), 9. Right Joystick (8 directions, 5 speed levels), 11. Status LEDs, 12. Display, 13. AUX 3, 10. AUX 4.
8.2 Emergency Stop Button (1)
- Stop: Press to disconnect receiver power; all functions are disabled.
- Unlock: Turn clockwise until the button pops out.
8.3 Status LEDs (11)
| Status | Green | Red |
|---|---|---|
| Slow flashing | - | - |
| Fast flashing | Sending | - |
| On | - | Transmitting blocked |
| Flashing | Battery low | - |
8.4 Display (12)
Shows battery status, STOP indicator, transmitting blocked status, transmission start, switch/button status, and joystick status.
8.5 Switching On/Off
- Important: The receiver powers on automatically with the connected device.
- To enable remote transmission: Ensure all switches are OFF, controls are untouched, and the Emergency Stop button (1) is unlocked.
- Switching On: Turn the ON/OFF switch (7) to ON. Press the green transmission enabling button (8).
- Switching Off: Turn the ON/OFF switch (7) to OFF.
9. Belt
The belt supports holding the remote. It can be worn around the neck during operation or over the shoulder for transport. Connect the carabiner hooks to the eyelets on the back of the remote control.
10. Troubleshooting
| Problem | Possible Cause | Suggested Solution |
|---|---|---|
| Green status LED flashes. | Receiver without power. | Check receiver power supply. Check receiver fuses (inspect for damage, replace if blown). |
| Red status LED flashes. | Remote control battery is depleted. | Replace the battery. |
| Contact springs in the battery compartment are corroded. | Clean the contact springs in the battery compartment. |
11. Cleaning and Care
Important: Do not use aggressive cleaning agents, rubbing alcohol, or chemical solvents, as they can damage the housing and cause malfunctions. Do not immerse the product in water. Clean with a dry, lint-free cloth.
12. Disposal
12.1 Product
This device is marked with the WEEE symbol, indicating it should not be disposed of with unsorted municipal waste. Users must dispose of it separately. End users are responsible for data deletion. Observe local regulations for disposal and recycling.
12.2 Batteries
- Remove and dispose of batteries/rechargeable batteries separately. Do not dispose of in household waste.
- Batteries containing hazardous substances are marked with a symbol indicating prohibition of disposal in household waste.
- Return used batteries to collection points. Cover terminals with insulating tape before disposal to prevent short circuits.
13. Declaration of Conformity (DOC)
Conrad Electronic SE declares that this product complies with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at www.conrad.com/downloads.
14. Technical Data
14.1 Remote Control (Transmitter)
| Parameter | Value |
|---|---|
| Model | Q5000-U |
| Power Supply | 7.4 V Battery |
| Rechargeable Battery | 7.4 V, 2200 mAh, LiPo |
| Ingress Protection | IP65 |
| Dimensions | 245 x 140 x 180 mm |
| Weight | 1.58 kg (including battery) |
14.2 Receiver
| Parameter | Value |
|---|---|
| Model | Q5000-U |
| Power Supply | via 2 connection wires |
| Input Voltage | 12-24 V AC/DC |
| Input Power | 5-7 W |
| Relay Load Current | 7 A |
| Output Contact | 250 V @ 7 A |
| Fuses | 4x 10 A (1 Fuse per COM connection) |
| Amount of Connection Wires | 40 |
| Address Code | 32-bit |
| Ingress Protection | IP65 |
| Dimensions | 220 x 205 x 70 mm |
| Weight | 1.68 kg |
14.3 Wireless Transmission
| Parameter | Value |
|---|---|
| Frequency Range | 420.125-450.000 MHz |
| Transmission Power | < 100 mW |
| Transmission Distance | < 100 m |
| Command Response Time | < 50 ms |
| Modulation | GFSK |
| Antenna Impedance | 50 Ω |
| Mode of Operation | Simplex (real-time control technology) |
14.4 Environment
| Parameter | Value |
|---|---|
| Operating Temperature | -25 to +75 °C |
| Storage Temperature | -35 to +80 °C |
14.5 Data according to EU Regulation 2019/1782
| Parameter | Value |
|---|---|
| Manufacturer | Conrad Electronic SE, Klaus-Conrad-Str. 1, 92240 Hirschau, Germany |
| Commercial Registration Number | HRB 3896 |
| Model Identifier | SG-084100012LE |
| Input Voltage | 100-240 V/AC |
| Input AC Frequency | 50/60 Hz |
| Output Voltage | 8.4 V/DC |
| Output Current | 1.0 A |
| Output Power | 8.4 W |
| Average Active Efficiency | 75.6% |
| Efficiency at Low Load (10%) | 86.1% |
| No Load Power Consumption | 0.03 W |
Conrad Electronic » All parts of success
