Connects2 CTSFO008.2 Ford Steering Wheel Control Interface
Version 1.04/18
Vehicle Application
This interface is compatible with the following Ford vehicles:
- Ford Ranger 2012>
- Ford B-Max 2012>
- Ford Kuga 2013>
- Ford Fiesta (JA8, US & Euro Models) 2012>
- Ford C-Max (DXA) 2010>
- Ford Focus (DYB) 2011>
- Ford Transit Custom (FCC, Not Euro 6) 2012 - 2016
- Ford Escape 2013>
- Ford Ecosport 2013>
- Ford Transit Connect 2013>
- Ford Taurus 2008 - 2012
Key Features
- Retains Steering Wheel Controls (if equipped)
- Retains Time/Date Change
- Retains Parking Sensor Audio
- Provides Speed Pulse, Park Brake, Reverse Gear, Antenna Remote & Illumination
About This Product
The CTSFO008.2 is a CAN-Bus Steering Wheel Control Interface for Ford vehicles. It retains essential vehicle functions such as steering wheel controls, parking sensor audio, and allows for time/date adjustments directly from the steering wheel.
Wiring Colour Codes
| Wire Colour | Function | Wire Colour | Function |
|---|---|---|---|
| Purple | Right Rear Speaker + | Yellow | Permanent 12V |
| Purple/Black | Right Rear Speaker - | Black | Ground |
| Green | Left Rear Speaker + | Red | Ignition 12V |
| Green/Black | Left Rear Speaker - | Orange | Illumination |
| Grey | Right Front Speaker + | Green | Park Brake |
| Grey/Black | Right Front Speaker - | Pink | Speed Pulse |
| White | Left Front Speaker + | Purple/White | Reverse Gear |
| White/Black | Left Front Speaker - | Blue/White | Antenna Remote |
Prior to Installation
Read the manual thoroughly before installation. Technical knowledge is required. Ensure the installation location is dry and away from heat sources. Use appropriate tools to prevent damage to the vehicle or product. Connects2 is not liable for installation errors.
Technical Support
Connects2 Ltd. offers technical support for any installation issues. To contact the support team, please submit a ticket at support.connects2.com, providing detailed information about the problem.
Fitting Guide
- Remove and disconnect the original head unit.
- Connect the 12-way molex connector of the head unit patch lead (supplied separately) to the interface.
- Connect the other end of the head unit patch lead to the steering wheel control input on the back of the aftermarket head unit. Note: This may be a 3.5mm jack plug or a wire input depending on the head unit brand. Refer to the head unit's installation manual for details. Important: This step must be completed before connecting power to the interface to ensure steering wheel control functionality.
- Connect the 14-way molex connector to the interface.
- Connect the male power/speaker ISO harness to the female power/speaker ISO harness from the aftermarket head unit. For units without an ISO connector, refer to the "Wiring Colour Codes" on Page 2.
- Connect the female vehicle-specific connectors on the harness to the corresponding male vehicle connectors.
- Connect the chime speaker box to the loom using the 4-pin connector and the red/white RCA connectors to the stereo Aux Input.
- Remove the car display connector from the vehicle and plug it into the interface (ensure the dust cover is removed from the interface first).
- Connect the display connector from the loom to the vehicle's display port (the port previously occupied by the car display connector removed in Step 8).
Test the head unit for correct operation.
Steering Wheel Control Functionality
| Original Button | Function |
|---|---|
| Volume + | Volume + |
| Volume - | Volume - |
| Track + | Track + |
| Track - | Track - |
| Speech | Mute |
Setting the Time/Date
- Press 'Speech' to turn on the vehicle display.
- Press and hold 'Speech' for two seconds to enter menu mode.
- Press 'Volume +/-' to navigate to the clock setting menu and press 'Speech' to confirm.
- Adjust the time using 'Volume +/-' and press 'Speech' to confirm.
- Follow the same process to adjust the date.
- Once the time and date are set, press 'Speech' to confirm.
Note: The menu will time out after 15-20 seconds of inactivity.
Connects2
