Product Overview
This document provides instructions for assembling the Yaheetech Rolling 2-Story Animal Cage. The cage is designed for small animals such as chinchillas, rats, and ferrets. It features a multi-level design with removable ramps and platforms, and is mounted on wheels for easy mobility.
Important Assembly Information:
- [1 or more people recommended] for assembly.
- Estimated assembly time: [1 hour].
- This product is [Not intended for use by children].
- [Keep away from fire or other heat sources].
- [We recommend wearing protective gloves] during assembly.
Assembly Precautions
To prevent damage to the product or your flooring during assembly, please follow the instructions carefully and use a protective pad or cover underneath the cage components.
Visual Guide:
Diagram showing a box labeled 'CARTON' and a person discarding a trash bin with a red cross symbol, indicating an incorrect method (cage placed directly on floor). The second diagram shows the same box and cage, with a person using a protective pad and a green checkmark symbol, indicating the correct method to avoid damage during assembly.
Parts List
| Part ID | Description | Quantity |
|---|---|---|
| ① | Wire Panel | 2 |
| ② | Wire Panel | 2 |
| ③ | Base Panel | 1 |
| ④ | Wire Panel | 1 |
| ⑤ | Wire Panel | 4 |
| ⑥ | Wire Panel | 1 |
| ⑦ | Tray/Shelf | 1 |
| ⑧ | Frame Part | 1 |
| ⑨ | Frame Part | 1 |
| ⑩ | Base Panel | 1 |
| ⑪ | Frame Part | 2 |
| ⑫ | Ramp/Platform | 3 |
| ⑬ | Ramp/Platform | 2 |
| ⑭ | Caster Wheel | 4 |
| ⑮ | Screw (30mm) | 24 |
| ⑯ | Screw (25mm) | 8 |
| ⑰ | Plastic Connector | 3 |
| ⑱ | Plastic Connector | 2 |
| ⑲ | Allen Wrench | 1 |
Assembly Steps
General Instruction: During assembly, please first half-tighten all screws into the holes. After all screws are set, fully tighten them.
Step 1
Attach two wire panels (①) and two wire panels (②) to the base panel (③) using eight screws (⑮). The diagram shows these panels forming the lower sides and back of the cage.
Step 2
Attach one wire panel (④) and one wire panel (⑥) to the structure assembled in Step 1, using screws (⑮). This forms the upper rear and side sections.
Step 3
Assemble the base frame by attaching frame parts (⑧, ⑨, ⑪) and base panel (⑩) using screws (⑮). Attach four caster wheels (⑭) to the bottom of the base structure using screws (⑮).
Step 4
Attach the wire panels (⑤) to the sides of the cage structure. Install the tray/shelf (⑦) and secure it. The diagram shows screws (⑯) being used to attach shelves.
Step 5
Install the ramps/platforms (⑫, ⑬) and plastic connectors (⑰, ⑱). The diagrams illustrate how to connect the ramps/platforms to the cage levels using the plastic connectors.
Diagram NO.1: Shows parts (⑫) x3, (⑬) x2, (⑰) x3, (⑱) x2, illustrating how ramps/platforms connect.
Diagram NO.2: Shows a close-up of how the plastic connectors attach to the cage wire and the ramp/platform.
Support and Contact Information
If you are not entirely satisfied with your purchase, please feel free to contact the seller by following these steps:
- Go to Your Orders.
- Find your order in the list.
- Select "Problem with order".
- Choose your topic from the list displayed.
- Select "Contact seller".
Manufacturer: Made in PRC
Importer: Yahee GmbH, Hans-Grüninger-Weg 11, 71706 Markgröningen
You can also download the electronic Installation Manual from the "Product guides and documents" section of the advertising page.
