Keychron V2 Customizable Keyboard User Manual

Product Overview

This manual provides comprehensive instructions for the Keychron V2 Customizable Keyboard, Knob Version.

Available Versions

Fully Assembled Version

Includes:

• 1x Fully Assembled Keyboard
• 1x Case
• 1x PCB
• 1x Steel Plate
• 1x Sound Absorbing Foam
• 1x Silicone Bottom Pad
• 4 Sets x Stabilizers
• 1 Set x Keycaps (PBT Double-shot)
• 1 Set x Switches

Cable:

• 1x Type-C to Type-C Cable
• 1x Type-A to Type-C Adapter

Tools:

• 1x Switch Puller
• 1x Keycap Puller
• 1x Screwdriver
• 1x Hex Key

[Diagram: Illustration of the fully assembled keyboard layout]

Barebone Version

Includes:

• 1x Keyboard Kit (Without Keycaps & Switches)
• 1x Case
• 1x PCB
• 1x Steel Plate
• 1x Sound Absorbing Foam
• 1x Silicone Bottom Pad
• 4 Sets x Stabilizers

Cable:

• 1x Type-C to Type-C Cable
• 1x Type-A to Type-C Adapter

Tools:

• 1x Switch Puller
• 1x Keycap Puller
• 1x Screwdriver
• 1x Hex Key

[Diagram: Illustration of the barebone keyboard kit layout]

Quick Start Guide

If you are a Windows user, please find the appropriate keycaps in the box, then follow the instructions below to find and replace the following keycaps.

[Diagram: Keyboard layout showing Mac/Windows keycap differences and highlighted keys for replacement]

[Diagram: Labels pointing to Windows key and Alt key for Mac layout]

System Setup

1. Switch To The Right System

   Please make sure the system toggle on the top left corner has been switched to the same system as your computer's operating system.

   [Diagram: Close-up of the Mac/Win toggle switch on the keyboard]

   [Diagram: USB cables and a laptop icon indicating connection]

2. The VIA Key Remapping Software

   Please visit caniusevia.com to download the latest VIA software to remap the keys. If the VIA software cannot recognize your keyboard, please reach out to support for instructions.

   [Image: VIA software logo with text "Your keyboard's best friend"]

Keyboard Layers

The keyboard has five layers of key settings:

• Layer 0: Mac system
• Layer 1: Windows system
• Layer 2: Mac Multimedia keys
• Layer 3: Windows Multimedia keys
• Layer 4: Function keys

[Diagram: Visual representation of layers 0-4 with Mac/Win/Multimedia/Function labels]

If your system toggle is switched to Mac, then Layer 0 will be activated.

If your system toggle is switched to Windows, then Layer 1 will be activated.

Multimedia Key and Function Key

Multimedia Keys

[Diagram: Representation of multimedia key symbols]

To access Multimedia Keys, press fn1 + [specific keys].

Function Keys

[Diagram: Representation of F1-F12 keys]

To access Function Keys, press fn2 + [specific keys].

Backlight Controls

Changing Backlight Mode

Press fn1 + Q to change the lighting effect.

Press fn1 + Tab to turn the backlight on/off.

[Diagram: Keyboard highlighting fn1+Q keys]

[Diagram: Keyboard highlighting fn1+Tab keys]

Adjusting Backlight Brightness

Press fn1 + W to increase the backlight brightness.

Press fn1 + S to decrease the backlight brightness.

[Diagram: Keyboard highlighting fn1+W keys]

[Diagram: Keyboard highlighting fn1+S keys]

Adjusting Backlight Speed

Press fn1 + T to increase the light effect speed.

Press fn1 + G to decrease the light effect speed.

[Diagram: Keyboard highlighting fn1+T keys]

[Diagram: Keyboard highlighting fn1+G keys]

Warranty

The keyboard is highly customizable and easy to be rebuilt. If anything goes wrong with any of the keyboard components during the warranty period, only the defective parts will be replaced, not the whole keyboard.

[Image: "WARRANTY" stamp graphic]

Build Tutorial

If you are building the keyboard for the first time, it is highly recommended to watch the building tutorial video on the Keychron website first, then start building the keyboard yourself.

[Image: "TUTORIAL" stamp graphic]

Factory Reset

If the keyboard malfunctions, follow these steps:

1. Press and hold fn1 + J + Z for 4 seconds.
2. Download the correct firmware for your keyboard from the Keychron website. Disconnect the keyboard's data cable.
3. Remove the spacebar keycap to find the reset button on the PCB.
4. Hold the reset button while plugging in the keyboard's data cable, then release the reset key. The keyboard will enter DFU mode.
5. Flash the firmware using the QMK Toolbox.
6. Perform a factory reset again by pressing and holding fn1 + J + Z for 4 seconds.

* A step-by-step guide can be found on the Keychron website.

[Diagram: Keyboard layout showing the location of the reset button]

Specifications

Keyboard Layout Details

Mac Layout

[Diagram: Mac keyboard layout]

Windows Layout

[Diagram: Windows keyboard layout]

[Diagram: Side view of the keyboard showing ports and switches]

1. Type-C Port

2. Mac Layout (Toggle Position)

3. Windows Layout (Toggle Position)

Key Description

Important Notes

Third-party Input Tools Compatibility

Due to compatibility, versions, brands, and drivers of Windows/macOS, functionalities of third-party input tools may be affected while using the keyboard. Please ensure your operating system and drivers are up to date.

Fn Keys and Multimedia Keys in Windows/Android Mode

Certain Fn keys or multimedia keys may not work under Windows/Android mode. Functionalities of certain multimedia keys may be disabled due to compatibility, versions, brands, and drivers of Windows/Android OS.

Safety Precautions

• Keep the product, accessories, and packaging parts out of reach of children to prevent any accidents and choking hazards.
• Always keep the product dry to avoid corrosion.
• Do not expose the product to extreme temperatures below -10°C (5°F) or above 50°C (131°F) to preserve the lifespan of the keyboard.

Contact Information

Keychron, Inc.

Dover, DE 19901, United States

Find us at:

https://www.keychron.com

Support Email: Support@keychron.com

Social Media:

• Facebook: @keychron
• Instagram: @keychron
• Twitter: @keychronMK

Designed by Keychron

Made in China

China General Agent: 渴创技术(深圳)有限公司 (Keshi Chuang Technology (Shenzhen) Co., Ltd.)

Implementation Standard: GB/T 14081–2010

After-sales Hotline: 400-0766268

Address: Room 201, Building 2, Wenkeng Industrial Zone, Dafapou Community, Bantian Street, Longgang District, Shenzhen City