Installation Guide: Concealed Trap Toilet with L Bolts Brackets

NOTICE BEFORE INSTALLATION

Please read the instructions carefully before installing. The company will not be held responsible for problems caused by not following original instructions.

WATER PRESSURE

Water pressure standard: 0.15MPa-0.55MPa. To test, open the valve and let water run into a bucket for 15 seconds. If the bucket contains more than 4 liters, the minimum water pressure is met. Please adjust the angle to fit if the water pressure is too high.

Drainage operation: Turn on the angle valve and drain off water for over 2 minutes before installing the inlet tube onto the angle valve.

INSTALLATION SPACE

• Ensure there is enough space around the unit; confirm the bathroom door or shower door will not hit the unit when they open.
• Ensure the minimum distance from the wall to the center of the floor drain is 305mm (12 inches) long.
• A GFI plug is required close to the unit.

Diagram Description: An illustration shows an angle valve, wall, GFCI plug, and drain hole with dimensions indicating a 305mm (12 inch) distance. Another diagram illustrates the water pressure test setup with a valve, pipe, and bucket.

CAUTION

⚠️ The drawing plan is not to the actual scale of the unit. When doing the installation in cold weather, leave the unit in room temperature for at least four hours before installing.

Diagram Description: A diagram shows the overall dimensions of the toilet from different views, labeled with millimeters.

INSTALLATION STEPS

1. For a newly installed bathroom toilet, a flange with bolts shall be added. Note: Install the flange according to the size and position of the two bolt holes at the bottom of the ceramic. See Figure 1.

   Diagram Description: Illustrates the installation of a toilet flange with bolts, showing the waste outlet and the 12" (305mm) distance requirement.

2. Lift the flip lid assembly from the toilet, up from the inside. Note: Do not pull the lid roughly when lifting the toilet flip lid.

   Diagram Description: Shows the process of lifting the toilet lid.

3. Install a flange under the toilet.

   Diagram Description: Depicts installing a flange beneath the toilet bowl.

4. Put the toilet on the flange, making sure the bolts line up with the holes in the toilet (from the top).

   Diagram Description: Shows the toilet being placed onto the installed flange, aligning bolts.

5. Use a spanner to lock the nuts and other accessories to the retaining bolts (from the top).

   Diagram Description: Illustrates tightening retaining bolts with a spanner, showing nuts, gasket, and plastic screw washer.

6. To install the seat cover and ceramic bowl, the seat cover shall be aligned with the ceramic bowl. Then press down with hands.

   Diagram Description: Shows aligning the toilet seat cover with the ceramic bowl and pressing down.

7. Install the water inlet angle valve and connect the dedicated hose. Before connecting the hose, please drain for 3-5 minutes, ensuring the pipe is clean and won't be blocked.

   Diagram Description: Shows connecting the water inlet angle valve and dedicated hose, with a note to press tightly.

Note on pipes/valves: Pipes and valves could be different from the above graphic due to production batches; please refer to the actual product.

BATTERY INSTALLATION

1. Find Figure 2 to install the battery into the battery box.
2. Insert a new battery in the direction of the arrow and tighten the waterproof cap clockwise.
3. Press the flush button to make sure it flushes properly.

   Diagram Description: Illustrates installing a 9V alkaline battery into the toilet's battery box, showing the battery and its orientation.

Note:

• ⚠️ The intelligent toilet accessories have been debugged and are strictly prohibited for personal disassembly.
• Please use the fittings and hoses provided by the company. Old fittings and hoses cannot be reused.

MAINTENANCE

REGULAR MAINTENANCE

Cleaning the unit

1. Gently wipe dirt and stains with a dry soft cloth or sponge; do not apply any chemical solutions to the unit.

   Diagram Description: Shows a toilet being wiped with a cloth.

Cleaning the nozzle

1. Works when the user is not sitting on the unit. Press the female clean button on the side button; the nozzle will stretch out and the self-cleaning function will initiate. When self-cleaning function is on, the nozzle will not spray water. Gently wipe the nozzle with a soft cloth or brush with a toothbrush.
2. The cleansing schedule is 90 seconds; the nozzle will be static for the first 70 seconds and will move back and forth for the last 20 seconds. The nozzle will retract back to the unit after cleansing. Repeat the process if necessary.
3. Warning: Do not apply force by pulling, pushing, or attempting to bend the nozzle, as this will result in damage or electrical shock.

   Diagram Description: Illustrates the toilet nozzle extending and moving during the self-cleaning cycle.

Cleaning the filter

1. Power off the unit, unplug the power cord with a dry hand. Use a tool to unscrew the filter if necessary.
2. Rinse with clear water, use a brush if necessary.
3. Install the filter back to its original position and check for leakage.

   Diagram Description: Shows a filter component and a brush, indicating the cleaning process.

Detailed Installation Steps (with L Bolts Brackets)

The following steps detail the installation process, particularly for concealed trap toilets using L-shaped mounting brackets.

1. Diagram Description: Shows applying a wax ring or sealant to the toilet base or flange.

2. Diagram Description: Illustrates a template or guide being placed on the floor for marking bolt hole positions.

3. Diagram Description: Shows the toilet base positioned over the drain hole and flange.

4. Diagram Description: Depicts drilling a hole, possibly for a wall anchor, with a 3/8" drill bit indicated.

5. Diagram Description: Shows bolts and washers being prepared for attachment to the toilet base or mounting brackets.

6. Install the mounting L-shaped brackets.

   Diagram Description: Shows L-shaped brackets being attached to the floor or wall, with screws and wall anchors. A detailed view shows the components of a screw and anchor.

7. Place the Wax ring.

   Diagram Description: Shows a wax ring being placed onto the toilet outlet flange.

8. Apply weight evenly.

   Diagram Description: Shows hands pressing down on the toilet to ensure even weight distribution.

9. Carefully lower the toilet over the mounting brackets.

   Diagram Description: Shows the toilet being lowered onto the floor, aligning with mounting points.

10. Install the bolts into the bracket and tighten evenly. Do not overtighten! Affix bolt caps after installation.

    Diagram Description: Shows bolts being inserted into brackets and tightened, with a close-up of a bolt, washer, and bolt cap.